Caterpillar Cat CB-534B VIBRATORY COMPACTOR (Prefix 4JL) Service Repair Manual Instant Download

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 1/3 Shutdown SIS Previous Screen Product: VIBRATORY COMPACTOR Model: CB-534B VIBRATORY COMPACTOR 4JL Configuration: CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY 3054 ENGINE Disassembly and Assembly 3054 Engine for Caterpillar Built Machines Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008 i02253357 Gear Group (Front) - Remove SMCS - 1206-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 8S-2264 Puller Group 1 B 173-9774 Wrench Bit 1 Start By: A. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 2/3 Illustration 1 g00556563 Note: It may be necessary to pin the fuel pump in order to maintain the correct timing. Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove"for the correct procedure. 1. Align the timing marks on the crankshaft gear, the camshaft gear, and the idler gear, as shown. 2. Remove bolts (1) from idler gear (2) . 3. Remove idler gear (2) and retainer plate (3) . Illustration 2 g00556757 4. Remove bushing (4) from idler gear (2) , if necessary. 5. Remove the bushing with a suitable puller. If the bushing cannot be removed with a puller, grind the face off of one bushing. The remainder of the bushing can then be removed with a press. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 3/3 Illustration 3 g00556758 6. Remove idler gear hub (5) from the cylinder block. 7. Remove nut (6) and the spring washer from fuel injection pump gear (8) . 8. Remove bolts (7) from fuel injection pump gear (8) . Note: Some fuel injection pump gears may have a tamper proof torx screw in place of one of the four bolts. Use Tooling (B) to remove the tamper proof torx screw, if necessary. 9. Use Tooling (A) to remove fuel injection pump gear (8) . Copyright 1993 - 2021 Caterpillar Inc. Tue May 11 17:09:39 UTC+0800 2021 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 1/3 Shutdown SIS Previous Screen Product: VIBRATORY COMPACTOR Model: CB-534B VIBRATORY COMPACTOR 4JL Configuration: CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY 3054 ENGINE Disassembly and Assembly 3054 Engine for Caterpillar Built Machines Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008 i01744102 Gear Group (Front) - Install SMCS - 1206-012 Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 1 g00556758 1. Install fuel injection pump gear (8) on the engine. 2. Install bolts (7) on fuel injection pump gear (8). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 2/3 3. Install nut (6) and the spring washer on fuel injection pump gear (8). Tighten the nut to a torque of 80 N m (59 lb ft). 4. Install idler gear hub (5) on the engine. Illustration 2 g00556757 5. Use a suitable press to install new bushings (4) into idler gear (2). 6. Machine the bores for clearance on idler gear hub (5). The bore should have a clearance of 0.04 to 0.010 mm (0.0016 to 0.0039 inch) on idler gear hub (5). The bore can have a diameter of 57.14 to 57.18 mm (2.250 to 2.251 inch). 7. Machine the front faces of the bushings for the end play of idler gear (2). The gear and the bushings can have a thickness of 30.14 to 30.16 mm (1.186 to 1.187 inch). Illustration 3 g00556563 8. Install idler gear (2) and retainer plate (3) on the engine. Note: Ensure that the timing marks on the camshaft gear, the crankshaft gear, and the idler gear are aligned. 9. Install bolts (1) on idler gear (2). Tighten the bolts to a torque of 44 N m (32 lb ft). 10. Check the end play of idler gear (2). Idler gear (2) should have end play of 0.10 to 0.20 mm (0.004 to 0.008 inch). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 3/3 11. Check the backlash between the camshaft gear and idler gear (2). The gears must have a minimum backlash of 0.08 mm (0.003 inch). End By: a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Install". Copyright 1993 - 2021 Caterpillar Inc. Tue May 11 17:10:35 UTC+0800 2021 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 1/2 Shutdown SIS Previous Screen Product: VIBRATORY COMPACTOR Model: CB-534B VIBRATORY COMPACTOR 4JL Configuration: CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY 3054 ENGINE Disassembly and Assembly 3054 Engine for Caterpillar Built Machines Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008 i01744128 Housing (Front) - Remove SMCS - 1151-011 Removal Procedure Start By: a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install". b. Remove the front gear group. Refer to Disassembly and Assembly, "Gear Group (Front) - Remove". c. Remove the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 2/2 Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. Illustration 1 g00549819 1. Remove all bolts (1) that fasten the front housing (2) to the cylinder block. Illustration 2 g00549821 2. Remove bolts (3) that hold the oil pan to the bottom of front housing (2). 3. Remove front housing (2) and the gasket. Copyright 1993 - 2021 Caterpillar Inc. Tue May 11 17:11:31 UTC+0800 2021 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 1/3 Shutdown SIS Previous Screen Product: VIBRATORY COMPACTOR Model: CB-534B VIBRATORY COMPACTOR 4JL Configuration: CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY 3054 ENGINE Disassembly and Assembly 3054 Engine for Caterpillar Built Machines Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008 i06815567 Housing (Front) - Install SMCS - 1151-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A - Loctite Gasket Sealant No. 2 - NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Replace the gasket. 2. Apply Tooling (A) to the bottom portion of the gasket. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 2/3 Illustration 1 g00549821 3. If necessary, install the studs (not shown) to the back of the front housing (2) that holds the fuel injection pump in position. Tighten the studs to a torque of 11 N m (97 lb in). Install the gasket and front housing (2). Cut the gasket to the correct length, if necessary. 4. Install bolts (3) that hold the engine oil pan to the bottom of the front housing. Tighten the bolts to a torque of 22 N m (16 lb ft). Illustration 2 g00549819 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 3/3 Illustration 3 g03549798 5. Install all bolts (1) that fasten the front housing (2) to the cylinder block and to the oil pan. Tighten bolts (1) to a torque of 22 N m (16 lb ft) using the sequence in Illustration 3. Note: Ensure that the bottom of the front housing is aligned with the bottom of the cylinder block. End By: a. Install the camshaft gear. b. Install the front gear group. c. Install the engine oil pan. Copyright 1993 - 2021 Caterpillar Inc. Tue May 11 17:12:27 UTC+0800 2021 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 1/5 Shutdown SIS Previous Screen Product: VIBRATORY COMPACTOR Model: CB-534B VIBRATORY COMPACTOR 4JL Configuration: CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY 3054 ENGINE Disassembly and Assembly 3054 Engine for Caterpillar Built Machines Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008 i01054405 Valve Mechanism Cover - Remove and Install SMCS - 1107-010 Removal Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. Note: The engines are equipped with either an aluminum valve cover or with a composite valve cover. The aluminum valve cover has a seal that fits between the valve cover and the inlet https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 2/5 manifold. The composite valve cover has a seal that is permanently fixed to the side of the valve cover. Illustration 1 g00547002 Typical example Illustration 2 g00547003 Aluminum valve cover https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 3/5 Illustration 3 g00547004 Composite valve cover 1. Loosen hose clamp (1) . 2. Disconnect breather hose (2) . 3. Remove three nuts (3), steel washers (6), and sealing washers (8) . Note: When you remove nuts (3), ensure that the nuts on the rocker arm bracket are not loosened. Note: Current production engines have an additional shim washer (7) . 4. Remove valve cover (4), gasket (10), and seal (5) . 5. Remove seal (9) for the oil filler cap. Installation Procedure Note: The engines are equipped with either an aluminum valve cover or with a composite valve cover. The aluminum valve cover has a seal that fits between the valve cover and the inlet manifold. The composite valve cover has a seal that is permanently fixed to the side of the valve cover. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 4/5 Illustration 4 g00547002 Typical example Illustration 5 g00547003 Aluminum valve cover https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 5/5 Illustration 6 g00547004 Composite valve cover 1. Inspect the condition of the gaskets and the seals. Replace the gaskets and the seals, if necessary. 2. Install seal (9) for the oil filler cap, if necessary. 3. Apply 8T-9022 Silicone Gasket to gasket (10) . Note: Ensure that the flat face of the gasket is toward the valve cover. 4. Install gasket (10), seal (5), and valve cover (4) . 5. Lubricate three nuts (3) with clean engine oil. 6. Install three nuts (3), steel washers (6), and sealing washers (8) . Note: When you install three nuts (3) without shim washers (7), tighten the nuts to a torque of 20 N m (15 lb ft). Do not overtighten the nuts. Note: When you install three nuts (3) with shim washers (7), tighten the nuts to a torque of 30 N m (22 lb ft). Do not overtighten the nuts. 7. Connect breather hose (2) . 8. Tighten hose clamp (1) . Copyright 1993 - 2021 Caterpillar Inc. Tue May 11 17:13:22 UTC+0800 2021 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 1/2 Shutdown SIS Previous Screen Product: VIBRATORY COMPACTOR Model: CB-534B VIBRATORY COMPACTOR 4JL Configuration: CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY 3054 ENGINE Disassembly and Assembly 3054 Engine for Caterpillar Built Machines Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008 i01761173 Rocker Shaft and Pushrod - Remove SMCS - 1102-011; 1208-011 Removal Procedure Start By: a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 1 g00635152 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 2/2 Typical example Note: It is not necessary to remove the oil supply tube in order to remove the rocker shaft assembly and the pushrods. 1. Remove nuts (1) and bolt (2) from the rocker shaft assembly. Begin with the end brackets and move toward the center. 2. Remove rocker shaft assembly (3). 3. Remove the oil seal from the oil supply passage in the cylinder head. Illustration 2 g00635153 Typical example 4. Remove pushrods (4). Place an identification mark on the pushrods for installation. Copyright 1993 - 2021 Caterpillar Inc. Tue May 11 17:14:18 UTC+0800 2021 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 1/3 Shutdown SIS Previous Screen Product: VIBRATORY COMPACTOR Model: CB-534B VIBRATORY COMPACTOR 4JL Configuration: CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY 3054 ENGINE Disassembly and Assembly 3054 Engine for Caterpillar Built Machines Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008 i01667090 Rocker Shaft - Disassemble SMCS - 1102-015 Disassembly Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 1P-0510 Driver Group 1 Start By: A. Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove". Illustration 1 g00550061 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 2/3 1. Use a screwdriver or a similar tool to remove retaining ring (1) from both ends of the rocker shaft assembly. Illustration 2 g00550062 (1) Retaining ring (2) Washer on the end of the rocker shaft (3) Rocker arm assembly (4) Rocker shaft bracket (5) Spring on the rocker shaft (6) Washer (7) Rocker shaft (8) Bolt (9) Oil supply connection (10) Rocker arm bushing 2. Remove the rocker arms and the rocker shaft brackets from the rocker shaft assembly. Note: Place an identification mark on each of the components for the proper order for installation. 3. Check the clearance between rocker arm assembly (3) and rocker shaft (7). Replace rocker arm bushing (10) if the clearance is larger than 0.13 mm (0.005 inch). Use Tool (A) and a suitable press in order to remove rocker arm bushing (10) from rocker arm assembly (3), if necessary. 4. Remove rocker shaft bracket (4) from rocker shaft (7) . 5. Remove springs (5), washer (6), bolt (8) and oil supply connection (9) from rocker shaft (7) . Tue May 11 17:15:14 UTC+0800 2021 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 1/2 Shutdown SIS Previous Screen Product: VIBRATORY COMPACTOR Model: CB-534B VIBRATORY COMPACTOR 4JL Configuration: CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY 3054 ENGINE Disassembly and Assembly 3054 Engine for Caterpillar Built Machines Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008 i01667093 Rocker Shaft - Assemble SMCS - 1102-016 Assembly Procedure 1. Lubricate all of the components with clean engine oil. Illustration 1 g00550062 (1) Retaining ring (2) Washer on the end of the rocker shaft (3) Rocker arm assembly (4) Rocker shaft bracket (5) Spring on the rocker shaft (6) Washer (7) Rocker shaft https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 2/2 (8) Bolt (9) Oil supply connection (10) Rocker arm bushing 2. Install oil supply connection (9) and bolt (8) on rocker shaft (7) . Note: Ensure that the bolt and the connection are correctly positioned on the rocker shaft. Note: Ensure that all of the oil holes in the rocker shaft and in the rocker arms are not plugged before you begin the assembly procedure. 3. Install rocker arm bushing (10) in rocker arm assembly (3) with a suitable press. Ream the bushing to a clearance of 0.06 0.03 mm (0.0024 0.0012 inch), if necessary. 4. Install each of the components in the correct order onto rocker shaft (7). See Illustration 1. Illustration 2 g00550061 5. Install retaining ring (1). End By: Install the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install". Copyright 1993 - 2021 Caterpillar Inc. Tue May 11 17:16:10 UTC+0800 2021 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 1/2 Shutdown SIS Previous Screen Product: VIBRATORY COMPACTOR Model: CB-534B VIBRATORY COMPACTOR 4JL Configuration: CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY 3054 ENGINE Disassembly and Assembly 3054 Engine for Caterpillar Built Machines Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008 i01749382 Rocker Shaft and Pushrod - Install SMCS - 1102-012; 1208-012 Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 1 g00635153 Typical example 1. Install pushrods (4). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 2/2 Note: Ensure that the pushrods are installed in the original location and that the pushrods are seated in the valve lifters correctly. 2. Install a new oil seal in the oil supply hole in the cylinder head. Illustration 2 g00635152 Typical example 3. Put rocker shaft assembly (3) in position on the cylinder head. Make sure that the connection for the oil supply is installed correctly into the oil seal. Note: Ensure that the adjustment screws are properly seated in the ends of pushrods (4). Note: It may be necessary to loosen the adjustment screws on each rocker arm. This will help prevent a bent valve or a bent pushrod during the installation of the rocker shaft. 4. Lubricate nuts (1) and bolt (2) with clean engine oil. 5. Install nuts (1) and bolt (2). 6. Alternately tighten the nuts and the bolt. Start from the center and work toward the outside. Tighten the nuts and the bolt on an aluminum bracket to a torque of 40 N m (30 lb ft). Tighten the nuts and the bolt on a cast iron or a steel bracket to a torque of 75 N m (55 lb ft). 7. Adjust the inlet valve lash to 0.20 mm (0.008 inch) and adjust the exhaust valve lash to 0.45 mm (0.018 inch). Refer to Testing and Adjusting, "Air Inlet and Exhaust System" for more information on adjusting the valve lash. End By: a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install". Copyright 1993 - 2021 Caterpillar Inc. Tue May 11 17:17:05 UTC+0800 2021 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 1/4 Shutdown SIS Previous Screen Product: VIBRATORY COMPACTOR Model: CB-534B VIBRATORY COMPACTOR 4JL Configuration: CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY 3054 ENGINE Disassembly and Assembly 3054 Engine for Caterpillar Built Machines Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008 i01645897 Cylinder Head - Remove SMCS - 1100-011 Removal Procedure Start By: A. Disconnect the electrical connections at the battery. B. Drain the coolant system. If the engine uses Diesel Engine Antifreeze/Coolant (DEAC), refer to Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change". If the engine uses Extended Life Coolant (ELC), refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change". C. Remove the air inlet manifold. Refer to Disassembly and Assembly, "Air Inlet Manifold - Remove". D. Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold - Remove and Install". E. Remove the fuel injection nozzles. Refer to Disassembly and Assembly, "Fuel Injection Nozzles - Remove". F. Remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove and Install". G. Remove the water outlet manifold. Refer to Disassembly and Assembly, "Water Outlet Manifold - Remove". H. Remove the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly, "Rocker Arm and Shaft - Remove". https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 2/4 Illustration 1 g00550160 Typical example Illustration 2 g00550162 1. Gradually loosen 22 cylinder head bolts (1) in the reverse order that is shown in Illustration 2. This will help prevent distortion of the cylinder head. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 3/4 Illustration 3 g00550163 Typical example 2. Attach a suitable lifting device to cylinder head (2). Carefully lift cylinder head (2) off the engine block. The weight of the cylinder head is 41 kg (90 lb). NOTICE Place the cylinder head on a surface that will not scratch the face of the cylinder head. Illustration 4 g00550165 3. Remove cylinder head gasket (3) . 4. Note the location of dowels (4) on each end of the cylinder block. Dowels (4) hold cylinder head gasket (3) in place while cylinder head (2) is installed. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 4/4 Illustration 5 g00741112 5. Align straight edge (7) with bolt (6) in order to check for distortion. If there is a visible reduction in the diameter of thread (8) that has not been in engagement with the cylinder block, the bolts must be replaced. Copyright 1993 - 2021 Caterpillar Inc. Tue May 11 17:18:01 UTC+0800 2021 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

Suggest: If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 1/4 Shutdown SIS Previous Screen Product: VIBRATORY COMPACTOR Model: CB-534B VIBRATORY COMPACTOR 4JL Configuration: CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY 3054 ENGINE Disassembly and Assembly 3054 Engine for Caterpillar Built Machines Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008 i01645901 Cylinder Head - Install SMCS - 1100-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 9U-6238 Guide Bolt 2 B 8T-3052 Degree Wheel 1 1. Thoroughly clean the top of the cylinder block and the bottom of the cylinder head. Ensure that there is no debris in the cylinder bores. Illustration 1 g00550165 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY ... 2/4 2. Place cylinder head gasket (3) on dowels (4) on top of the cylinder block. The cylinder head gasket (3) is stamped "FRONT TOP". Do not use any sealant or compound on the cylinder head gasket. 3. Install Tool (A) in positions 15 and 20 in the cylinder block. Refer to Illustration 4. Illustration 2 g00550163 Typical example 4. Attach a suitable lifting device to cylinder head (2) . 5. Place cylinder head (2) on the cylinder block. Ensure that the cylinder head is positioned on dowels (4) and that cylinder head gasket (3) is positioned correctly. 6. Remove Tool (A) . Illustration 3 g00550160 Typical example 7. Lubricate cylinder head bolts (1) with clean engine oil. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/5/11

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com