Caterpillar Cat M313C WHEELED Excavator (Prefix H2A) Service Repair Manual Instant Download

Service Repair Manual Models M 313C WHEELEDExcavator

w 1/7(W) Shutdown SIS Previous Screen Product: WHEELED EXCAVATOR Model: M313C WHEELED EXCAVATOR H2A Configuration: M313C Excavator H2A00001-UP (MACHINE) POWERED BY 3054E Engine Disassembly and Assembly M313C Wheeled Excavator Power Train Media Number -RENR8617-00 Publication Date -01/04/2006 Date Updated -17/04/2006 i02405149 Travel Brake Valve - Assemble SMCS - 4265-016 Assembly Procedure NOTICE Keep all parts clean from contaminants. Contamination of the hydraulic system with foreign material will reduce the service life of the hydraulic system components. To prevent contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected. Cover any disassembled components and clean them properly before assembly. Clean the hydraulic system properly after any major component exchange or especially after a component failure, to remove any contamination. Note: Cleanliness is an important factor. Before the assembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

w 2/7(W) Illustration 1 g01185275 1. Install shuttle valve (29). Illustration 2 g01185274 2. Install the O-ring seals on plugs (26), (27), and (28). Install plugs (26), (27), and (28). Tighten plugs (26), (27), and (28) to a torque of 20 N m (15 lb ft). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com

w 3/7(W) Illustration 3 g00893672 3. Install piston (24) and spring (25). Illustration 4 g00893671 Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. 4. Install poppet (23). 5. Repeat Steps 3 through 4 for the opposite side of the valve. 6. Install plug (22) and the O-ring seal. Tighten plug (22) to a torque of 90 N m (66 lb ft). Illustration 5 g00893670 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

w 4/7(W) Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. 7. Install piston (17), piston (19), spring (20), spring seats (18), and retaining bolt (21) onto valve assembly (15). Illustration 6 g00893669 8. Install plug (16) into valve assembly (15). Illustration 7 g00893668 9. Install valve assembly (15). 10. Install piston (12) and spring (13). 11. Install O-ring seals (14). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

w 5/7(W) Illustration 8 g00893667 Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. 12. Install cover (9). 13. Position block (10) and install bolts (11). Tighten bolts (11) to a torque of 130 N m (96 lb ft). Illustration 9 g00893666 14. Install piston (6) and spring (5) into brake control valve (8). 15. Install O-ring seals (7). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

w 6/7(W) Illustration 10 g00893665 Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. 16. Install plug (2). 17. Position cover (4). 18. Install bolts (3). Tighten bolts (3) to a torque of 130 N m (96 lb ft). Illustration 11 g00893664 19. Install O-ring seals (1). End By: a. Install the brake control valve. Refer to Disassembly and Assembly, "Brake Control Valve - Install". https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

w 1/2(W) Shutdown SIS Previous Screen Product: WHEELED EXCAVATOR Model: M313C WHEELED EXCAVATOR H2A Configuration: M313C Excavator H2A00001-UP (MACHINE) POWERED BY 3054E Engine Disassembly and Assembly M313C Wheeled Excavator Power Train Media Number -RENR8617-00 Publication Date -01/04/2006 Date Updated -17/04/2006 i02405152 Travel Brake Valve - Install SMCS - 4265-012 Installation Procedure Illustration 1 g01185247 1. Position brake control valve (2) and install bolts (3). Tighten bolts (3) to a torque of 10.4 N m (92 lb in). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

w 2/2(W) Illustration 2 g01185219 2. Install the O-ring seals on hose assemblies (1). Connect hose assemblies (1) to brake control valve (2). Copyright 1993 - 2020 Caterpillar Inc. Wed Apr 22 21:55:20 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

w 1/10(W) Shutdown SIS Previous Screen Product: WHEELED EXCAVATOR Model: M313C WHEELED EXCAVATOR H2A Configuration: M313C Excavator H2A00001-UP (MACHINE) POWERED BY 3054E Engine Disassembly and Assembly M313C Wheeled Excavator Power Train Media Number -RENR8617-00 Publication Date -01/04/2006 Date Updated -17/04/2006 i02512536 Final Drive Carriers, Hubs and Brakes - Disassemble - Front Axle SMCS - 4054-015; 4092-015; 4253-015; 4255-015 Disassembly Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 1P-1863 Retaining Ring Pliers 1 5F-7465 Puller Assembly 1 1S-5188 Puller leg 2 B 5P-4750 Adjustment Screw 1 1P-0510 Screw 1 C 267-6564 Spanner 1 D 1U-5832 Pry Bar 1 E 1U-6410 Three Jaw Puller 1 F 1P-0510 Driver Gp 1 G 5P-4197 Spacer 1 H 1A-1935 Full Nut 1 3H-0465 Push-Puller Plate 4 5F-7342 Adapter 2 5F-7343 Bearing Puller Gp 1 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

w 2/10(W) 5F-7366 Forcing Screw 1 5P-8248 Hard Washer 2 6B-6684 Full Nut 2 6V-8237 Washer 1 8B-7549 Puller Leg 2 9S-7338 Crossblock 1 Start By: A. Remove the front tires and rims. Refer to Disassembly and Assembly, "Tire and Rim - Remove". B. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release". NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. 1. Drain the oil from the front final drives into a suitable container. Illustration 1 g00894123 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

w 3/10(W) 2. Attach a suitable lifting device to carrier housing (2) . 3. Remove bolts (1) . 4. Remove carrier housing (2). The weight of carrier housing (2) is approximately 31 kg (68 lb). Illustration 2 g00894124 5. Disconnect hose assembly (3) . Illustration 3 g01136274 6. Use Tooling (A) in order to remove retaining rings (4) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

w 4/10(W) Illustration 4 g01136278 7. Use Tooling (B) in order to remove planetary gears (5) from carrier housing (2) . 8. Remove thrust washer (6) . Illustration 5 g01136281 9. Remove retaining ring (7), washer (8), and roller bearing (9) . Illustration 6 g01136284 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

w 5/10(W) 10. Use Tooling (A) in order to remove retaining ring (10). Remove thrust washers (11) and (12) . Illustration 7 g01183274 Illustration 8 g01183275 11. Remove bolt (13). Use Tooling (C) in order to remove nut (14) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

w 6/10(W) Illustration 9 g01136294 12. Remove O-ring seal (15). Remove ring gear housing (16) . Illustration 10 g01136296 Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. 13. Remove bolts (17), the springs, and the retainers. Remove piston (18) . Illustration 11 g01136302 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

w 7/10(W) 14. Remove O-ring seal (19), ring (20), O-ring seal (21), and ring (22) . Illustration 12 g01136306 15. Remove clutch discs (23) . Illustration 13 g01136310 16. Remove O-ring seal (24). Use Tooling (D) in order to remove carrier gear (25) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

w 8/10(W) Illustration 14 g01136323 17. Remove O-ring seal (26) . Illustration 15 g01136328 18. Use a suitable lifting device, Tooling (E), Tooling (F), and Tooling (G) in order to remove bearing cone (27) and flange (28) . Illustration 16 g01136332 19. Attach a suitable lifting device to flange (28) and remove flange (28). The weight of flange (28) is approximately 38 kg (83 lb). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

w 9/10(W) Illustration 17 g01136334 20. Remove seal (29). Remove bearing cups (30) . Illustration 18 g01136337 21. Remove spacer (31) . Illustration 19 g01136345 22. Use Tooling (F), Tooling (G), and Tooling (H) in order to remove bearing cone (32) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

w 1/10(W) Shutdown SIS Previous Screen Product: WHEELED EXCAVATOR Model: M313C WHEELED EXCAVATOR H2A Configuration: M313C Excavator H2A00001-UP (MACHINE) POWERED BY 3054E Engine Disassembly and Assembly M313C Wheeled Excavator Power Train Media Number -RENR8617-00 Publication Date -01/04/2006 Date Updated -17/04/2006 i02512623 Final Drive Carriers, Hubs and Brakes - Disassemble - Rear Axle SMCS - 4054-015; 4092-015; 4253-015; 4255-015 Disassembly Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 1P-1863 Retaining Ring Pliers 1 5F-7465 Puller Assembly 1 1S-5188 Puller Leg 2 B 5P-4750 Adjusting Screw 1 1P-0510 Driver Group 1 C 267-6564 Spanner 1 D 1U-5832 Pry Bar 1 E 1U-6410 Three Jaw Puller 1 F 1P-0510 Driver Gp 1 G 1A-1935 Full Nut 1 3H-0465 Push-Puller Plate 4 5F-7342 Adapter 2 5F-7343 Bearing Puller Gp 1 5F-7366 Forcing Screw 1 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

w 2/10(W) 5P-8248 Hard Washer 2 6B-6684 Full Nut 2 6V-8237 Washer 1 8B-7549 Puller Leg 2 9S-7338 Crossblock 1 Start By: A. Remove the rear tires and rims. Refer to Disassembly and Assembly, "Tire and Rim - Remove". B. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release". NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. 1. Drain the oil from the front final drives into a suitable container. Illustration 1 g01178408 2. Attach a suitable lifting device to carrier housing (2) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

w 3/10(W) 3. Remove bolts (3) . 4. Remove carrier housing (2). The weight of carrier housing (2) is approximately 31 kg (68 lb). 5. Disconnect hose assembly (1) . Illustration 2 g01136274 6. Use Tooling (A) in order to remove retaining rings (4) . Illustration 3 g01136278 7. Use Tooling (B) in order to remove planetary gears (5) from carrier housing (2) . 8. Remove thrust washer (6) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

w 4/10(W) Illustration 4 g01136281 9. Remove retaining ring (7), washer (8), and roller bearing (9) . Illustration 5 g01178409 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

w 5/10(W) Illustration 6 g01178410 10. Remove bolt (10). Use Tooling (C) in order to remove nut (11) . Illustration 7 g01178411 11. Remove O-ring seal (12). Remove stub shaft (13) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

w 6/10(W) Illustration 8 g01178413 Note: Note the location of the alignment marks on ring gear housing (14) and the hub for assembly purposes. 12. Use Tooling (D) to remove ring gear housing (14) . Illustration 9 g01178412 Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. 13. Remove the bolts, the springs, and retainers (15). Remove piston (16) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

w 7/10(W) Illustration 10 g01178414 14. Remove O-ring seal (17), ring (18), O-ring seal (19), and ring (20) . Illustration 11 g01178415 15. Remove brake discs (21) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

Suggest: If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading

w 8/10(W) Illustration 12 g01178416 16. Remove O-ring seal (23). Use Tooling (D) in order to remove carrier gear (22) . Illustration 13 g01178429 17. Remove O-ring seal (24) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/4/22

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com