Understanding Sedimentation: Types and Applications
Sedimentation is a physical treatment process that separates suspended solids from water using gravity. There are four types of sedimentation: discrete settling, flocculant settling, hindered settling, and compression settling. Each type describes different behaviors of solid particles as they settle in water. Proper design principles for sedimentation tanks are essential to ensure efficient removal of solids from water.
Download Presentation
Please find below an Image/Link to download the presentation.
The content on the website is provided AS IS for your information and personal use only. It may not be sold, licensed, or shared on other websites without obtaining consent from the author. Download presentation by click this link. If you encounter any issues during the download, it is possible that the publisher has removed the file from their server.
E N D
Presentation Transcript
Sedimentation is a physical treatment process that utilize a gravity separate suspended soilds from water. In general, there are four types of sedimentation:
Type I : known as discrete setling describes the sedimentation of low concentration of particles that settle as individual entities. Un this type of settling the particles settle unhindered at a constant velocity through water.
Type 2 Known as flocculant settling, describes sedimentation of larger concentration of solids that agglomerate as they settle. The particles begins to settle as discrete particles but their concentration is sufficiently high to ensure particle collision.
Type 3 Known as hindered settling describes the sedimentation of a suspension with solids concentration sufficiently high to cause the particles to settle as a mass e.g. the upper portion of the sludge blanket behave like type 3
Type 4 Known as compression settling , describes the sedimentation of suspension with soilds concentration so high that the particles are in contact with an another and further sedimentation can occur only by compression of the mass
14.0 PRINCIPLES OF HORIZONTAL FLOW SEDIMENTATION TANKS Given below are the principles of good sedimentation tank design. (a) In a continuous flow sedimentation tank, four zones must be present. i) an inlet zone to disperse influent flow and suspended section of the basin, ii) a settling zone in which settling takes place, iii) an outlet zone in which clarified water is collected of the tank and conduit, and iv) a sludge zone at the bottom in which the settled solids accumulate and from which they are withdrawn for disposal. matter uniformly over the cross uniformly over the cross-section directed to the outlet
(b) The criteria of settling in a horizontal flow tank are : i) ii) settling rate S depends on particle size, shape mass density, efficiency of a tank depends on the surface overflow rate) So , which is given by where Q is the rate of flow and A and loading (or So = Q/A is the surface area, iii) distribution suspended particles can be influenced by the tank, size, shape and mass density of the iv) efficiency is independent of depth H of the tank and of detention time To , and v) particles settle faster with depth due to part of the settling particles coalescing to form larger particles higher than the parent particles. clarification effect depends on frequency for the settling velocities of the and the value So which design of the particles, which settle at rates
(c) is In an ideal horizontal flow sedimentation tank, settling supposed to take place without any influence of the horizontal water movement (hazen and Camp model concept of overflow rate). In practice, however, horizontal flow sedimentation tanks operate at efficiencies less than that for ideal horizontal flow because := and scatter the and (i) there is influence by horizontal water movement transverse velocity components which pathways of discreet particles unequal causing eddying currents, induced currents or unequal clarified water over the width of the (ii) some distrubance is always present due to supply of flocculated water stagnant water, wind abstraction of tanks.
Settling Velocities for common suspensions Nature of Solid Specific Gravity Settling Velocity (m/h) Sand, Silt, Clay 2.650 0.25 Aluminium and Iron Floc 1.002 2.99 Calcium Carbonate Precipitates 1.200 1.51 Primary Waste Organic 1.001 1.51 Activated Sludge Organics 1.005 7.20 Source : Clarifier Design, Water Environment Federation (WEF), 2005
15.1 SEDIMENTATION Sedimentation allows the flocs to fall to the bottom in a sedimentation tank. These tanks are normally sized in accordance with the surface loading theory, which means that the particles to be separated must have sufficient time to sink to the bottom while the water passes through the tank. If the settlement velocity of the particles is V m/h, the water flow rate is Q m3/h and the surface area of the sedimentation tank is A m2, we obtain the following relationship : m3/h Vm/h = Q A m2
15.2 Rectangular Sedimentation Tank The design criteria for rectangular horizontal flow sedimentation tank are as follows: (a) The overflow rater ranges from 0.85 to 1.5m3/m2/hr. However, the rate commonly used is 1.5m3/m2/hr. (b) Detention time 2 4 hours (c) Preferred one being 4 : 1 The length to width ratio is between 3 : 1 and 5 : 1.
(d) The depth is in the range of 3 to 5 meters (e) Diffuser wall is required at the inlet where the velocity should be not more than 0.1 m/s (f) Loading outlet over weir should not exceeds 8m3/hr/m (per meter run) (g) Space to be provided for accumulation of sludge should be 10 to 15% of the tank volume. (h) Floor slope is recommended to be 1:50
15.3 Design of Rectangular Sedimentation Tank Q m3/h Surface Rate(m/h), V A m2 = 3500m3/h Q = V = 1.5m/hr Propose: Provide Ten (10) Rows of sedimentation tank 350m3/hr Q8 =
Qm3/h Surface Rate (m/h), V A m2 = Area, A = 350m3/hr 1.5m/hr 233m2 Area, A = Retention time, say t = 4 hours Tank capacity, Volume = 233m3/h x 4h = 932 m3 15% Sludge= 1072 m3 d = 4.6m depth Proposed Length to Width ratio 4 : 1
4B2 = 233 7.63m 7.35 m 7.63m 7.63m 7.63m B = 7.63 m L = 30.53 m d = 4.6m 30.53m 1 2 3 7 10
15.4 Lovo Sedimentation Tank The design criteria is as follows: (a) Surface loading should not exceed 1.5m3/m2/hr. (b) Detention time must not be less than 2 hrs. (c) Length to width ratio is between 2:1 and 4:1
(d) The depth recommended is 3 to 5 meters (e) A certain quantity of sludge accumulation (10 to 15% of tank capacity) should be allowed for in computing the capacity of the tank. (f) Inlet velocity into the sedimentation tank should be in the region of 0.1m/sec where as the outlet weir loading should be about 8m3/hr/m.
(g) The velocity of flow at mid-channel in the bottom half (Q/x-sectional Area) should not be greater than 0.05m/sec. In practice however 0.03m/s is commonly used in design. For the top half, 0.04 m/s is the design velocity. (h) The overflow should be positioned at the furthest end from the inlet and should be of sufficient size to cope with the over flow rate. (i) The floor slopes towards the inlet end at a gradient of 1 in 18 to 1 in 24, intermediate slanting slab that spans the whole width of the tank rises towards the collecting channel at the same range of gradients.
