Caterpillar Cat 631G WHEEL TRACTOR (Prefix CLR) Service Repair Manual Instant Download

w 1/9(W) Shutdown SIS Previous Screen Product: WHEEL TRACTOR Model: 631G WHEEL TRACTOR CLR Configuration: 631G Wheel Tractor CLR00001-UP (MACHINE) POWERED BY 3408E Engine Disassembly and Assembly 3408E and 3412E Engines for Caterpillar Built Machines Media Number -RENR2336-06 Publication Date -01/08/2018 Date Updated -10/08/2018 i01105362 HEUI Fluid Manifold - Remove and Install SMCS - 1126-010 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 138-7573 Link Bracket 2 Start By: a. Remove the injection actuation pressure sensor. Refer to Disassembly and Assembly, "Injection Actuation Pressure Sensor - Remove and Install". b. Remove the unit injector sleeves. Refer to Disassembly and Assembly, "Unit Injector Sleeve - Remove". c. Remove the rocker arm and shaft. Refer to Disassembly and Assembly, "Rocker Arm and Shaft - Remove". d. Remove the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve Mechanism Cover Base - Remove and Install". e. Remove the aftercooler. Refer to Disassembly and Assembly, "Aftercooler - Remove". NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 2/9(W) before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE The cylinder head must be removed and a new spacer plate gasket must be installed anytime the HEUI Fluid Manifold has been removed. Refer to Disassembly and Assembly, "Cylinder Head - Install" in this module. Illustration 1 g00570914 Typical example 1. Remove hose (1) from the front of the HEUI Fluid Manifold. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 3/9(W) Illustration 2 g00570923 Typical example 2. Remove hose (2) from the rear of the HEUI Fluid Manifold. Illustration 3 g00582732 Typical example 3. Remove tube assembly (3). Illustration 4 g00570979 Typical example 4. Remove cylinder head bolts (5) and the washers. Remove HEUI Fluid Manifold bolts (4). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com

w 4/9(W) Illustration 5 g00582745 Typical example 5. Install Tool (A) and a hoist on the HEUI Fluid Manifold. Remove HEUI Fluid Manifold bolts (7). Remove HEUI Fluid Manifold (6). The weight of the HEUI Fluid Manifold for the 3412E is 60 kg (131 lb). The weight of the HEUI Fluid Manifold for the 3408E is 39 kg (86 lb). Installation Procedure Table 2 Required Tools Tool Part Number Part Description Qty A 138-7573 Link Bracket 2 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE The cylinder head must be removed and a new spacer plate gasket must be installed anytime the HEUI Fluid Manifold has been removed. Refer to Disassembly and Assembly, "Cylinder Head - Install" in this module. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 5/9(W) Illustration 6 g00570607 HEUI fluid manifold for 3412E Illustration 7 g00582780 HEUI fluid manifold for 3408E Note: The bottom face of the HEUI Fluid Manifold and the top face of the cylinder head must be free of any contaminants during assembly. 1. Apply 8C-8422 Sealant in the shaded area of the HEUI Fluid Manifold. The 8C-8422 Sealant is applied to the bottom portion of the HEUI Fluid Manifold. The 8C-8422 Sealant is permitted on the entire face of the HEUI Fluid Manifold. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 6/9(W) Illustration 8 g00582745 Typical example 2. Install Tool (A) and a hoist on the HEUI Fluid Manifold. Install HEUI Fluid Manifold (6). The weight of the HEUI Fluid Manifold for the 3412E is 60 kg (131 lb). The weight of the HEUI Fluid Manifold for the 3408E is 39 kg (86 lb). Illustration 9 g00570979 Typical example 3. Install HEUI Fluid Manifold bolts (4) and (7). 4. Put clean engine oil on bolts (5) for the cylinder head. Install cylinder head bolts (5). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 7/9(W) Illustration 10 g00570761 Tightening sequence for 3412E Illustration 11 g00582808 Tightening sequence for 3408E 5. Tighten bolts (5) in the following step sequence: In a numerical sequence, tighten the bolts 1 through 26 for the 3412E. In a numerical sequence, tighten the bolts 1 through 18 for the 3408E. a. In a numerical sequence, tighten the bolts to a torque of 270 15 N m (200 11 lb ft). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 8/9(W) b. In a numerical sequence, tighten the bolts to a torque of 450 15 N m (330 11 lb ft). c. In a numerical sequence, again tighten the bolts to a torque of 450 15 N m (330 11 lb ft). 6. Tighten the upper row of nuts that are on the cylinder head in the following sequence. In a numerical sequence, tighten nuts 27 through 39 for the 3412E to a torque of 45 7 N m (33 5 lb ft). In a numerical sequence, tighten nuts 19 through 27 for the 3408E to a torque of 45 7 N m (33 5 lb ft). Illustration 12 g00582732 Typical example 7. Install tube assembly (3). Illustration 13 g00570923 Typical example 8. Install hose (2) on the rear of the HEUI Fluid Manifold. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 9/9(W) Illustration 14 g00570914 Typical example 9. Install hose (1) on the front of the HEUI Fluid Manifold. End By: a. Install the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve Mechanism Cover Base - Remove and Install". b. Install the rocker arm and shaft. Refer to Disassembly and Assembly, "Rocker Arm and Shaft - Install". c. Install the unit injector sleeves. Refer to Disassembly and Assembly, "Unit Injector Sleeve - Install". d. Install the injection actuation pressure sensor. Refer to Disassembly and Assembly, "Injection Actuation Pressure Sensor - Remove and Install". e. Install the aftercooler. Refer to Disassembly and Assembly, "Aftercooler - Install". Copyright 1993 - 2021 Caterpillar Inc. Mon Jun 14 18:34:05 UTC+0800 2021 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 1/4(W) Shutdown SIS Previous Screen Product: WHEEL TRACTOR Model: 631G WHEEL TRACTOR CLR Configuration: 631G Wheel Tractor CLR00001-UP (MACHINE) POWERED BY 3408E Engine Disassembly and Assembly 3408E and 3412E Engines for Caterpillar Built Machines Media Number -RENR2336-06 Publication Date -01/08/2018 Date Updated -10/08/2018 i01105933 Cylinder Head - Remove SMCS - 1100-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 5P-8700 Lifting Bracket 2 Start By: a. Remove the HEUI fluid manifold. Refer to Disassembly and Assembly, "HEUI Fluid Manifold - Remove and Install". b. Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 2/4(W) of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. Illustration 1 g00583128 Typical example 1. Install Tool (A) on the cylinder head. Remove nuts (1) that hold the cylinder head to the block. Illustration 2 g00583122 Typical example 2. Remove cylinder head (2). The weight of the cylinder head for the 3412E is 172 kg (380 lb). The weight of the cylinder head for the 3408E is 90 kg (200 lb). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 3/4(W) Illustration 3 g00583124 Typical example 3. Remove cylinder head gasket (3). Illustration 4 g00583123 Typical example 4. Remove coolant ferrules (4) from the spacer plate. 5. Remove spacer plate (5) from the cylinder block. Illustration 5 g00583125 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 4/4(W) Typical example 6. Remove two O-ring seals (6) and gasket (7) from the cylinder block. Copyright 1993 - 2021 Caterpillar Inc. Mon Jun 14 18:35:01 UTC+0800 2021 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 1/4(W) Shutdown SIS Previous Screen Product: WHEEL TRACTOR Model: 631G WHEEL TRACTOR CLR Configuration: 631G Wheel Tractor CLR00001-UP (MACHINE) POWERED BY 3408E Engine Disassembly and Assembly 3408E and 3412E Engines for Caterpillar Built Machines Media Number -RENR2336-06 Publication Date -01/08/2018 Date Updated -10/08/2018 i01105988 Cylinder Head - Install SMCS - 1100-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 5P-8700 Lifting Bracket 1 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Note: Thoroughly clean the spacer plate and the bottom surface of the cylinder head. A new spacer plate gasket must be installed when the cylinder head is removed. A new cylinder head gasket must be installed when the cylinder head is removed. Note: Check the condition of the O-rings. If the O-rings are worn or damaged, use new parts for replacement. Note: Put a thin film of clean engine oil on the seals and the O-ring seals prior to installation. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 2/4(W) Illustration 1 g00583125 Typical example 1. Install two O-ring seals (6) and spacer plate gasket (7) on the cylinder block. Illustration 2 g00583123 Typical example 2. Install spacer plate (5) on the cylinder block. 3. Install coolant ferrules (4) in the spacer plate. Illustration 3 g00583124 Typical example https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 3/4(W) 4. Install cylinder head gasket (3). Illustration 4 g00583122 Typical example 5. Install Tool (A) and a hoist on the cylinder head. Install cylinder head (2). The weight of the cylinder head for the 3412E is 172 kg (380 lb). The weight of the cylinder head for the 3408E is 90 kg (200 lb). Illustration 5 g00583128 Typical example 6. Install nuts (1) for the cylinder head finger tight. Remove Tool (A). End By: a. Install the HEUI fluid manifold. Refer to Disassembly and Assembly, "HEUI Fluid Manifold - Remove and Install". b. Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold - Remove and Install". Copyright 1993 - 2021 Caterpillar Inc. Mon Jun 14 18:35:56 UTC+0800 2021 All Rights Reserved. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 1/4(W) Shutdown SIS Previous Screen Product: WHEEL TRACTOR Model: 631G WHEEL TRACTOR CLR Configuration: 631G Wheel Tractor CLR00001-UP (MACHINE) POWERED BY 3408E Engine Disassembly and Assembly 3408E and 3412E Engines for Caterpillar Built Machines Media Number -RENR2336-06 Publication Date -01/08/2018 Date Updated -10/08/2018 i05933135 Lifter Group - Remove and Install SMCS - 1209-010 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 5P-7433 Valve Lifter Tool Group 1 Start By: A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 2/4(W) Illustration 1 g00571490 Illustration 2 g00571491 1. Install Tooling (A) in lifter assembly (1) . 2. Remove lifter assembly (1) from the lifter bore. Illustration 3 g00571492 3. Remove lifter guide spring (2) from the lifter assembly. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 3/4(W) Installation Procedure Table 2 Required Tools Tool Part Number Part Description Qty A 5P-7433 Valve Lifter Tool Group 1 Note: Install new valve lifter guide springs on the valve lifter when the valve lifters are removed from the engine. Note: Apply clean engine oil to the ball socket for the pushrod and the bore for the valve lifter assembly. Illustration 4 g00571513 1. Make an alignment of the new lifter guide spring (2) in Tooling (A) . Illustration 5 g01104989 2. Install lifter assembly (1) in the cylinder block with Tooling (A) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 4/4(W) End By: Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install". Copyright 1993 - 2021 Caterpillar Inc. Mon Jun 14 18:36:52 UTC+0800 2021 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 1/9(W) Shutdown SIS Previous Screen Product: WHEEL TRACTOR Model: 631G WHEEL TRACTOR CLR Configuration: 631G Wheel Tractor CLR00001-UP (MACHINE) POWERED BY 3408E Engine Disassembly and Assembly 3408E and 3412E Engines for Caterpillar Built Machines Media Number -RENR2336-06 Publication Date -01/08/2018 Date Updated -10/08/2018 i01605594 Camshaft - Remove SMCS - 1210-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 8S-1378 Stud Remover And Resetter Tool 1 B 9S-9082 Engine Turning Tool 1 C 1B-9575 Bolt 2 C 9M-1974 Hard Washer 2 D 1P-0510 Driver Gp 1 E 5P-0944 Dowel Puller Gp 1 F 1P-2321 Combination Puller 1 F 9S-9153 Puller Jaw 3 Start By: a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) Remove". b. Remove the lifter group. Refer to Disassembly and Assembly, "Lifter Group - Remove and Install". Engines Without a Camshaft Rear Gear https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 2/9(W) Illustration 1 g00572090 1. Rotate the engine until the timing marks V on the camshaft drive gear and the idler gear are aligned. Illustration 2 g00832971 2. Remove two bolts (1) and plate (2) from the camshaft. Illustration 3 g00832973 3. Remove camshaft (3) from the cylinder block. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 3/9(W) Illustration 4 g00832975 4. If necessary, remove camshaft drive gear (4) with Tool (D) and press. Engines With a Camshaft Rear Gear Note: All 3408E Engines have a balancer gear that is located in the flywheel housing. The balancer gear is driven by the crankshaft or the camshaft. The balancer gear has a timing mark. This timing mark must be aligned with the timing mark of the gear that drives the balancer gear. If there is access to the rear camshaft gear through the flywheel housing, the rear camshaft gear may be removed without removing the flywheel housing. If the balancer gear is driven by the crankshaft, the camshaft rear gear can be removed and installed without regarding the timing. If the balancer gear is driven by the camshaft rear gear, the timing marks on the camshaft rear gear and the balancer gear must be aligned when the camshaft rear gear is installed. Refer to Disassembly and Assembly, "Balancer Group - Remove" and Disassembly and Assembly, "Balancer Group - Install". 3412 Engines do not have a balancer gear. A dowel in the rear of the camshaft positions the rear camshaft gear on the camshaft. The rear camshaft gear is secured to the camshaft with four bolts. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 4/9(W) Illustration 5 g00832150 (5) Flywheel housing (6) Hole for turbocharger oil drain (7) Camshaft rear gear (8) Timing marks (9) Balancer gear 1. The procedure that follows is for flywheel housings that have a hole for the turbocharger oil drain. Access to the camshaft rear gear may be in several possible locations. The access will depend on the flywheel housing. Covers may need to be removed. The turbocharger oil drain line may need to be removed. If there is no possible access, the flywheel housing will need to be removed. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install". Refer to "The Flywheel Housing Has Been Removed" in this section. Note: If the balancer gear is driven by the camshaft rear gear, the timing marks on the camshaft rear gear and the balancer gear must be aligned.. If the balancer gear is driven by the crankshaft, the camshaft rear gear can be removed without regarding the timing. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 5/9(W) Illustration 6 g00832648 (10) Studs (11) Bolt (12) Camshaft rear gear 2. Remove the turbocharger oil drain line. Use Tool (A) and remove studs (10). Illustration 7 g00834273 3. The camshaft must be rotated in order to gain access to bolts (11). The last bolt will be removed when the threaded holes in the camshaft rear gear are in line with the threaded holes that mount the turbocharger oil drain line. The holes should be aligned when the engine is at top dead center. The camshaft will rotate once for every two rotations of the crankshaft. Look at the timing marks at the front of the engine on the camshaft drive gear and the idler gear. These timing marks must be aligned in order to thread Tool (C) into the camshaft rear gear. Turn the flywheel with Tool (B) and remove three of bolts (11) as the bolts become accessible. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 6/9(W) Illustration 8 g00834303 4. After the other three bolts have been removed and Tool (C) has been threaded into the camshaft rear gear, remove the bolt that is accessible when the engine is at top dead center. When the other three bolts have been removed, thread Tool (C) into the camshaft rear gear. Remove the fourth bolt (11). Note: Tool (C) must be used to hold the camshaft rear gear while the camshaft is removed. Tool (C) will keep the balancer gear engaged with the camshaft rear gear. Illustration 9 g00834315 5. Tighten Tool (C) evenly in order to remove the camshaft rear gear from the camshaft. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 7/9(W) Illustration 10 g00572090 6. Check that the timing marks (V) on the camshaft drive gear and the idler gear are aligned. Illustration 11 g00833004 7. Remove two bolts (13) and plate (14) from the camshaft. Illustration 12 g00833007 8. Remove camshaft (15) from the cylinder block. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 8/9(W) Illustration 13 g00833008 9. If necessary, remove camshaft gear (16) with Tool (D) and press. Illustration 14 g00834376 10. If necessary, use Tool (E) in order to remove dowel (20) from the camshaft. The Flywheel Housing Has Been Removed https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

w 9/9(W) Illustration 15 g00832518 1. Loosen four bolts (17). loosen the bolts approximately 6.4 mm (0.25 inch). Use Tool (F) and loosen the camshaft rear gear (18) from the camshaft. 2. Remove Tool (F). Remove four bolts (17) and the camshaft rear gear (18). 3. Refer to "Engines With a Camshaft Rear Gear". Use Step 6 through Step 10. Copyright 1993 - 2021 Caterpillar Inc. Mon Jun 14 18:37:48 UTC+0800 2021 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

Suggest: If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading

w 1/11(W) Shutdown SIS Previous Screen Product: WHEEL TRACTOR Model: 631G WHEEL TRACTOR CLR Configuration: 631G Wheel Tractor CLR00001-UP (MACHINE) POWERED BY 3408E Engine Disassembly and Assembly 3408E and 3412E Engines for Caterpillar Built Machines Media Number -RENR2336-06 Publication Date -01/08/2018 Date Updated -10/08/2018 i01611142 Camshaft - Install SMCS - 1210-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 9S-9082 Engine Turning Tool 1 B 8S-1378 Stud Remover and Resetter Tool 1 C 1B-9575 Bolt 2 C 9M-1974 Hard Washer 2 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Engines Without a Camshaft Rear Gear https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2021/6/14

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com