Caterpillar Cat 320C LRR Excavator (Prefix GAD) Service Repair Manual Instant Download

service repair manual l.w
1 / 34
Embed
Share

Please open the website below to get the complete manualnn//

rayaanacharya
Douglas2 Follow

Uploaded on | 0 Views

Download Presentation

Please find below an Image/Link to download the presentation.

The content on the website is provided AS IS for your information and personal use only. It may not be sold, licensed, or shared on other websites without obtaining consent from the author. Download presentation by click this link. If you encounter any issues during the download, it is possible that the publisher has removed the file from their server.

E N D

Presentation Transcript

  1. Service Repair Manual Models 320C LRR Excavator

  2. w 1/4(W) Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01564836 Fuel Filter Base - Remove and Install SMCS - 1262-010 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 185-3630 Strap Wrench Assembly 1 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  3. w 2/4(W) Dispose of all fluids according to local regulations and mandates. Illustration 1 g00813127 1. Use Tool (A) to remove fuel filter (3) from fuel filter base (2) . Note: It is not necessary to remove the fuel filter in order to remove the fuel filter base. 2. Remove banjo bolts (1) and copper washers in order to disconnect the fuel lines (4) from the fuel filter base (2). Note: Cap all openings or plug all openings immediately in order to prevent contamination of the fuel system. Illustration 2 g00813147 3. Remove two bolts (5) and the washers that secure the fuel filter base (2) to the air inlet manifold. Remove the fuel filter base (2) from the fuel filter bracket. Installation Procedure https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  4. https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com

  5. w 3/4(W) NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 3 g00813147 1. Place the fuel filter base (2) in position on the fuel filter bracket. Install the washers and two bolts (5) that secure the fuel filter base tothe fuel filter bracket. Illustration 4 g00813127 2. Install the banjo bolts (1) and install new copper washers in order to connect the fuel lines (4) to the fuel filter base (2) . 3. If the fuel filter was removed, install the fuel filter (3) to the fuel filter base (2). Tighten the fuel filter by hand according to the instructions that are shown on the fuel filter. Do not overtighten the fuel filter. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  6. w 1/5(W) Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01565021 Fuel Injection Lines - Remove and Install SMCS - 1252-010 Removal Procedure Start By: A. Remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  7. w 2/5(W) Illustration 1 g00606301 The 3066 Engine is shown. 1. Remove the bolts (1), the washers, and the clamps (2), which secure the fuel lines to the inlet manifold (3) . Illustration 2 g00606310 2. Disconnect the fuel injection lines (4) from the fuel injection nozzles (5) . Note: Cap all openings or plug all openings immediately in order to prevent contamination of the fuel system. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  8. w 3/5(W) Illustration 3 g00606314 Fuel injection pump for a 3066 Engine 3. Disconnect the end of the fuel injection lines (4) from the fuel injection pump (6) . Note: Cap all openings or plug all openings immediately in order to prevent contamination of the fuel system. 4. Remove the fuel injection lines (4) from the engine. Illustration 4 g00606317 5. Loosen the acorn nuts (7), which secure the fuel return line to the fuel injection nozzles. 6. Remove one bolt (8) and the washer from the clamp that secures the fuel return line to the intake manifold. Note: The clamp will remain with the fuel return line, when the fuel return line is removed from the engine. 7. Disconnect fitting (9). Remove fuel return line (10) from the engine. Note: Cap all openings or plug all openings immediately in order to prevent contamination of the fuel system. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  9. w 4/5(W) Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 5 g00606317 1. Place the fuel return line (10) in position on the engine. Connect fitting (9) of the fuel return line to the fuel injection pump. 2. Install the washer and bolt (8) through the clamp in order to secure the fuel return line to the inlet manifold. 3. Install the fuel return line (10) to the fuel injection nozzles. Secure the fuel return line to the fuel injection nozzle with acorn nuts (7) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  10. w 5/5(W) Illustration 6 g00606399 Fuel injection pump for a 3066 Engine 4. Place the fuel injection lines (4) on the engine. 5. Connect the fuel injection lines (4) to the fuel injection pump (6) . 6. Connect the fuel injection lines (4) to the fuel injection nozzles (5) . Note: The fuel lines (4) should be connected at the fuel injection nozzle (5) and at the fuel injection pump (6) before tightening the nuts for the fuel injection line. 7. Tighten the nuts for the fuel injection line to a torque of 25 N m (18 lb ft). Illustration 7 g00606301 Fuel lines for a 3066 Engine 8. Install the clamps (2), the washers, and the bolts (1), which secure the fuel lines to the inlet manifold (3) . End By: Install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove and Install". Copyright 1993 - 2019 Caterpillar Inc. Sat Oct 26 09:29:25 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  11. w 1/2(W) Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01151321 Fuel Injection Nozzles - Remove SMCS - 1254-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 1U-7600 Slide Hammer Puller 1 B 9U-6278 Adapter 1 Start By: A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  12. w 2/2(W) Illustration 1 g00652319 1. Remove bolt (1) and the washer that secures the clamp (2) to the cylinder head assembly. 2. Remove the clamp (2) that secures the fuel injection nozzle (3) in position in the cylinder head assembly. Note: Put caps or plugs on all openings immediately in order to prevent contamination in the fuel system. Note: Mark the clamp for later installation. 3. Install Tool (B) (not shown) to the fuel injection nozzle. Note: Tool (B) is installed at the connection (4) for the fuel injection lines. 4. Connect Tool (A) (not shown) to Tool (B) in order to carefully remove fuel injection nozzle (3) . Note: Align the centerline of Tool (A) with the extended centerline of fuel injection nozzle (3). This procedure will help prevent distortion of the fuel injection nozzle which can cause the fuel injection nozzle to bend or break. 5. Remove the seat washer from the fuel injection nozzle. Copyright 1993 - 2019 Caterpillar Inc. Sat Oct 26 09:30:21 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  13. w 1/2(W) Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01151648 Fuel Injection Nozzles - Install SMCS - 1254-012 Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 1 g00652319 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  14. w 2/2(W) 1. Install a new seat washer (5) . 2. Install fuel injection nozzle (3). 3. Install clamp (2), the washer, and bolt (1) that secures the fuel injection nozzle to the cylinder head assembly. 4. Tighten bolt (1), that secures the fuel injection nozzle, to a torque of 22 N m (16 lb ft). End By: Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove and Install". Copyright 1993 - 2019 Caterpillar Inc. Sat Oct 26 09:31:17 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  15. w 1/2(W) Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01615152 Fuel Shutoff Solenoid - Remove and Install SMCS - 1259-010 Removal Procedure Illustration 1 g00618938 1. Disconnect two wire leads (1). Mark the wires for later installation. 2. Disconnect actuator lever (2) from the governor lever. 3. Remove two bolts (3) and washers that secure the fuel shutoff solenoid to the bracket. 4. Remove shutoff solenoid (4) from the bracket. Installation Procedure https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  16. w 2/2(W) Illustration 2 g00618938 1. Place the shutoff solenoid (4) in position on the bracket. 2. Install the two washers and bolts (3) that secure the fuel shutoff solenoid to the bracket. 3. Connect actuator lever (2) to the governor lever. 4. Connect two wire leads (1) to the fuel shutoff solenoid. Ensure that the wires are properly connected. Copyright 1993 - 2019 Caterpillar Inc. Sat Oct 26 09:32:12 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  17. w 1/3(W) Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01565175 Fuel Injection Pump - Remove SMCS - 1251-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 9U-6124 Universal Metric Socket Set 1 B 9U-6128 Universal Metric Socket (1) 1 ( 1 ) Part of the Universal Metric Socket Set Start By: A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  18. w 2/3(W) of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. 1. Ensure that the engine is the top center position on number one piston. Refer to Testing and Adjusting, "Finding Center Position for No. 1 Piston". Illustration 1 g00813442 2. Remove bolts (1) and washers that secure the cover (2) to the engine front housing. 3. Remove the access cover. Note the timing marks on the fuel injection pump drive gear and the idler gear for later installation. Illustration 2 g00813430 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  19. w 3/3(W) 4. Scribe a line across the front plate (3) and the mounting flange for the fuel injection pump (4). This ensures proper alignment for the installation of fuel injection pump (8) . 5. Loosen fitting (5) for oil line (6) . 6. Remove oil line (6) from nipple (7) (not shown). Note: Put caps or plugs on all openings immediately in order to prevent contamination. 7. Use a lifting sling and a hoist in order to secure the fuel injection pump. The weight of the fuel injection pump is 13 kg (29 lb). Note: Use Tool (B) to remove the bolts and the washers that mount the fuel injection pump (8) . 8. Remove bolt (9) and the washer from the cylinder block. 9. Remove four bolts (10) and the washers that secure the fuel injection pump to the front housing. Illustration 3 g00813593 10. Remove the fuel injection pump (8). The gear and the mounting flange will remain with the fuel injection pump. Note: The fuel injection pump must be mounted to the engine in order to loosen the nut for the drive gear. Note: Do not rotate the engine after the fuel injection pump is removed. 11. Ensure that the old gasket material is removed from all mating surfaces of the pump mounting flange and the face of the fuel injection pump flange. Copyright 1993 - 2019 Caterpillar Inc. Sat Oct 26 09:33:08 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  20. w 1/2(W) Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01565619 Fuel Injection Pump - Install SMCS - 1251-012 Installation Procedure Table 1 Required Tools Tool Part number Part Description Qty A 9U-6124 Universal Metric Socket Set 1 B 9U-6128 Universal Metric Socket (1) 1 ( 1 ) Part of the Universal Metric Socket Set NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Note: If the nut for the fuel injection pump drive gear is removed, you must tighten the nut for the fuel injection pump drive gear to 88 5 N m (65 4 lb ft). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  21. w 2/2(W) Illustration 1 g00813430 1. Use a lifting sling and a hoist in order to secure the fuel injection pump (8). The weight of the fuel injection pump is 13 kg (29 lb). 2. Install a new gasket and install fuel injection pump (8) . 3. Ensure that the engine is in the top center position on No. 1 piston. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston". 4. Ensure that the mark on the front plate (3) and the mark on the fuel injection pump flange (4) are aligned. Refer to Testing and Adjusting, "Fuel Injection Timing-Check" for more information on fuel injection pump timing. Note: Use Tool (B) to install the bolts and washers that secure the fuel injection pump to the cylinder block. 5. Install the washers and bolts (9) that secure the fuel injection pump to the engine cylinder block. 6. Remove the sling from the fuel injection pump. 7. Connect oil line (6) to nipple (7) (not shown). 8. Tighten fitting (5) for oil line (6) . Copyright 1993 - 2019 Caterpillar Inc. Sat Oct 26 09:34:04 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  22. w 1/3(W) Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01564499 Turbocharger - Remove SMCS - 1052-011 Removal Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  23. w 4/4(W) 9. Remove snap ring (11) from compressor housing (12) . 10. Separate compressor housing (12) from the cartridge (10) . Copyright 1993 - 2019 Caterpillar Inc. Sat Oct 26 09:35:56 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  24. w 1/3(W) Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01147762 Turbocharger - Assemble SMCS - 1052-016 Assembly Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Note: During the assembly procedure, ensure that the index marks are aligned when the components are assembled. Illustration 1 g00608452 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  25. w 2/3(W) Illustration 2 g00608415 1. Install cartridge (10) into compressor housing (12) . 2. Install snap ring (11) into compressor housing (12) . Illustration 3 g00608342 3. Install cartridge (10) into turbine housing (9) . 4. Install clamp (8) that secures cartridge (10) and turbine housing (9) together. Install the bolt and nut (7) into clamp (8). Note: Refer to the Specifications Module, "Turbocharger" for information on the clamp. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  26. w 3/3(W) Illustration 4 g00608210 5. Inspect the condition of the gaskets. Replace the gaskets, if necessary. 6. Install gasket (6) on the turbine housing. 7. Install gasket (5) on the cartridge. Illustration 5 g00608212 8. Place oil supply line (4) in position. Secure the oil supply line with bolt (2) (not shown). 9. Place oil return line (3) in position. Secure the oil return line with two bolts (1) . End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install". Copyright 1993 - 2019 Caterpillar Inc. Sat Oct 26 09:36:51 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  27. w 1/2(W) Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01564587 Turbocharger - Install SMCS - 1052-012 Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Inspect the condition of all gaskets. Replace the gaskets, if necessary. Illustration 1 g00608177 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  28. w 2/2(W) 2. Install metal gasket (10) (not shown). Install turbocharger (3), oil supply line (4) and oil return line (6) (not shown) as a unit. 3. Install eight nuts (9). Tighten the nuts to a torque of 41 N m (30 lb ft). Note: Two nuts are installed on each turbocharger mounting stud. Illustration 2 g00812846 4. Slide hose (7) down the oil return line (6) onto fitting (8) . 5. Tighten two clamps (5) on hose (7) . 6. Connect oil supply line (4) to the cylinder block. Copyright 1993 - 2019 Caterpillar Inc. Sat Oct 26 09:37:47 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  29. w 1/3(W) Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01565722 Exhaust Manifold - Remove and Install SMCS - 1059-010 Removal Procedure Start By: A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 1 g00605454 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  30. w 2/3(W) 1. Remove the nuts (1) and washers that secure the exhaust manifold to the cylinder head assembly. The 3066 Engine has twelve nuts and washers while the 3064 Engine has eight nuts and washers. 2. Remove exhaust manifold (2) from the cylinder head assembly. 3. Remove exhaust manifold gasket (3) that is located between exhaust manifold (2) and the cylinder head assembly. Note: The 3066 Engine has two exhaust manifold gaskets, while the 3064 Engine has one exhaust manifold gasket. Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 2 g00605454 1. Install exhaust manifold gasket (3) between exhaust manifold (2) and the cylinder head assembly. Note: The 3066 Engine has two exhaust manifold gaskets, while the 3064 Engine has one exhaust manifold gasket. 2. Place exhaust manifold (2) in position on the cylinder head. 3. Install the nuts (1) and the washers that secure the exhaust manifold to the cylinder head assembly. The 3066 Engine has twelve nuts and washers while the 3064 Engine has eight nuts and washers. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  31. w 3/3(W) 4. Tighten exhaust manifold nuts (1) to a torque of 18 4 N m (13 3 lb ft). End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install". Copyright 1993 - 2019 Caterpillar Inc. Sat Oct 26 09:38:43 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  32. Suggest: If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading

  33. w 1/3(W) Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320C EXCAVATOR GAD Configuration: 320C LRR Excavator GAD00001-UP (MACHINE) POWERED BY 3066 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01615211 Air Inlet Heater - Remove and Install SMCS - 1090-010 Removal Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 1 g00611147 1. Loosen hose clamp (1) that secures air inlet hose (2) to air inlet elbow (4) . 2. Disconnect air inlet hose (2) from air inlet elbow (4) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/10/26

  34. https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com

Related


Guidelines for Gender and Development Budgeting in DepEd Orders

Guidelines for Gender and Development Budgeting in DepEd Orders

denn286
Guidelines on Gender and Development (GAD) Attribution

Guidelines on Gender and Development (GAD) Attribution

salman
The MHCAG in 2023 and 2024

The MHCAG in 2023 and 2024

paolo
Understanding Data Collection Techniques in Epidemiology

Understanding Data Collection Techniques in Epidemiology

brent
Implementation of Mental Health Prevention Services in My Health LA: Challenges and Best Practices

Implementation of Mental Health Prevention Services in My Health LA: Challenges and Best Practices

dylanie
Understanding Gender Sensitivity Training in the Legal Mandate

Understanding Gender Sensitivity Training in the Legal Mandate

tana802
GPU Scheduling Strategies: Maximizing Performance with Cache-Conscious Wavefront Scheduling

GPU Scheduling Strategies: Maximizing Performance with Cache-Conscious Wavefront Scheduling

aila
The Cat and the Bell: A Charming Story of Surprise

The Cat and the Bell: A Charming Story of Surprise

will_omo
Understanding Cat Aggression and How to Deal with It

Understanding Cat Aggression and How to Deal with It

nyear
Understanding Cat Body Language: A Comprehensive Guide

Understanding Cat Body Language: A Comprehensive Guide

kar_sa
Greedy Cat - A Fun and Entertaining Story by Kauri

Greedy Cat - A Fun and Entertaining Story by Kauri

kar_b
Impending Cuts to Accident Benefits: A Comprehensive Review

Impending Cuts to Accident Benefits: A Comprehensive Review

evertonha
Exploring Words with the Prefix

Exploring Words with the Prefix "bi-" for Children

kburk
IPv6 Networking Considerations in xDSL Networks

IPv6 Networking Considerations in xDSL Networks

nrari
Enhancing Interdomain Routing Security with RPKI

Enhancing Interdomain Routing Security with RPKI

yunker_b
Service-Learning Project UCA's Feral Cat Population Fall 2017

Service-Learning Project UCA's Feral Cat Population Fall 2017

schenker_k
Nine Lives Cat Café - Tour Reflections and Recommendations

Nine Lives Cat Café - Tour Reflections and Recommendations

stiorra
Understanding Cat Fines in Marine Fuel Oil Contamination

Understanding Cat Fines in Marine Fuel Oil Contamination

christal
Analysis of 'The Black Cat' by Edgar Allan Poe

Analysis of 'The Black Cat' by Edgar Allan Poe

thibert_v
The Future of Computer-Assisted Translation: Insights and Trends

The Future of Computer-Assisted Translation: Insights and Trends

bren_80
Analysis of Symbols in Edgar Allan Poe's 'The Black Cat'

Analysis of Symbols in Edgar Allan Poe's 'The Black Cat'

xaniyahk
Streamlining Compensation Administration with CAT Implementation

Streamlining Compensation Administration with CAT Implementation

maky
Lunch for Greedy Cat by Kauri 2 - A Delightful Visual Journey

Lunch for Greedy Cat by Kauri 2 - A Delightful Visual Journey

goin_ara
The LaPerm Cat: A Unique Feline Breed

The LaPerm Cat: A Unique Feline Breed

fie_nyl

More Related Content