Caterpillar Cat 305.5E2 CR Mini Hydraulic Excavator (Prefix NC5) Service Repair Manual Instant Download

Service Repair Manual Models 305.5E2 CR M ini Hydraulic Excavator

305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY ... 1/2 Shutdown SIS Previous Screen Product: MINI HYD EXCAVATOR Model: 305.5E2 CR MINI HYD EXCAVATOR NC5 Configuration: 305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY C2.4 Engine Disassembly and Assembly C2.4 Tier 4 Final Engines for Caterpillar Built Machines Media Number -UENR7319-02 Publication Date -01/07/2018 Date Updated -01/08/2018 i06523433 Inlet Manifold - Remove and Install SMCS - 1058-010 Removal Procedure Start By: a. Remove exhaust gas recirculation valve. b. Remove fuel injection lines. c. Remove fuel manifold (rail). Illustration 1 g06008649 1. Remove bolt (1). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/2/7

305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY ... 2/2 Illustration 2 g06008673 2. Remove bolts (2) and inlet manifold (3). Installation Procedure 1. Install inlet manifold (3) in the reverse order of removal. Copyright 1993 - 2020 Caterpillar Inc. Fri Feb 7 23:12:26 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/2/7

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com

305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY ... 1/4 Shutdown SIS Previous Screen Product: MINI HYD EXCAVATOR Model: 305.5E2 CR MINI HYD EXCAVATOR NC5 Configuration: 305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY C2.4 Engine Disassembly and Assembly C2.4 Tier 4 Final Engines for Caterpillar Built Machines Media Number -UENR7319-02 Publication Date -01/07/2018 Date Updated -01/08/2018 i06539555 Inlet and Exhaust Valves - Remove and Install SMCS - 1105-010 Removal Procedure Table 1 Required Tooling Tool Part Number Part Description Qty A 5S-1330 Valve Spring Compressor 1 Start By: a. Remove cylinder head. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Clean the bottom mating surface of the cylinder head. Check the depth of the valves below the face of the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder Head Valves" for the correct dimensions. 2. Place a temporary identification mark on the heads of the valves to identify the correct position. 3. Use a suitable lifting device to position the cylinder head with the valve springs upward. The weight of the cylinder head is approximately 28 kg (61 lb). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/2/7

305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY ... 2/4 Illustration 1 g06013564 Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. 4. Install Tooling (A) in position on the cylinder head and compress the valve spring to remove inlet and exhaust valves (1). Illustration 2 g06013581 NOTICE Ensure that the valve spring is compressed squarely or damage to the valve stem may occur. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/2/7

305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY ... 3/4 5. Remove valve cap (2). Apply sufficient pressure to Tooling (A) to remove valve keepers (3). 6. Slowly release pressure on Tooling (A). 7. Place a temporary identification make on valve spring (5) to identify the correct position. 8. Remove valve spring retainer (4), valve spring (5), and valve (6). 9. Remove Tooling (A). Illustration 3 g06013653 10. Remove valve stem seals (7) from the cylinder head. 11. Repeat Step 4 through Step 10 for the remaining valves. Installation Procedure 1. Install valves (6) in the reverse order of removal. 2. Clean all components of the cylinder head assembly. Ensure that all posts, all coolant passages, and all lubrication passages in the cylinder head are free from debris. Follow Step 2.a through Step 2.e to inspect components of the cylinder head assembly. Replace any components that are worn or damaged. a. Inspect the cylinder head for wear and for damage. Refer to System Operation, Testing and Adjusting, "Cylinder Head Inspect" for the correct procedure. b. Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder Head Valves" for further information. c. Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder Head Valves" for further information. d. Inspect the valves (6) for wear and for damage. Refer to Specifications, "Cylinder Head Valves" for further information. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/2/7

305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY ... 4/4 e. Inspect valve springs (5) for damage and for the correct length. Refer to Specifications, "Cylinder Head Valves" for further information. 3. Lubricate the stems of valves (6) with clean engine oil. Install valves (6) in the appropriate positions in the cylinder head. Check the depth of the valves below the face of the cylinder head. Refer to Specifications, "Cylinder Head Valves" for more information. Copyright 1993 - 2020 Caterpillar Inc. Fri Feb 7 23:13:23 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/2/7

305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY ... 1/2 Shutdown SIS Previous Screen Product: MINI HYD EXCAVATOR Model: 305.5E2 CR MINI HYD EXCAVATOR NC5 Configuration: 305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY C2.4 Engine Disassembly and Assembly C2.4 Tier 4 Final Engines for Caterpillar Built Machines Media Number -UENR7319-02 Publication Date -01/07/2018 Date Updated -01/08/2018 i06546055 Engine Oil Cooler - Remove and Install SMCS - 1378-010 Removal Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Dispose of all fluids according to local regulations and mandates. 1. Drain the coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct draining and filling procedures. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/2/7

305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY ... 2/2 Illustration 1 g06003514 2. Remove engine oil filter (1). Illustration 2 g06003538 3. Remove clamp (3) and clamp (5). Disconnect hose assembly (2) and hose assembly (4). 4. Remove connector (7), engine oil cooler (6), and the collar. Installation Procedure 1. Install engine oil cooler (6) in the reverse order of removal. a. Tighten connector (7) to a torque of 40 N m to 44 N m (30 lb ft to 32 lb ft). Copyright 1993 - 2020 Caterpillar Inc. Fri Feb 7 23:14:19 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/2/7

305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY ... 1/2 Shutdown SIS Previous Screen Product: MINI HYD EXCAVATOR Model: 305.5E2 CR MINI HYD EXCAVATOR NC5 Configuration: 305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY C2.4 Engine Disassembly and Assembly C2.4 Tier 4 Final Engines for Caterpillar Built Machines Media Number -UENR7319-02 Publication Date -01/07/2018 Date Updated -01/08/2018 i06546117 Engine Oil Pump - Remove and Install SMCS - 1304-010; 1315-010 Removal Procedure Table 1 Required Tooling Tool Part Number Part Description Qty A 1P-2321 Puller As. 1 Start By: a. Remove front housing. Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Dispose of all fluids according to local regulations and mandates. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/2/7

305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY ... 2/2 Illustration 1 g06009577 1. Remove nut (3). 2. Use Tooling (A) to remove gear (1). 3. Remove bolts (2), engine oil pump (4), and the gasket. Installation Procedure 1. Install engine oil pump (4) in the reverse order of removal. Copyright 1993 - 2020 Caterpillar Inc. Fri Feb 7 23:15:16 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/2/7

305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY ... 1/3 Shutdown SIS Previous Screen Product: MINI HYD EXCAVATOR Model: 305.5E2 CR MINI HYD EXCAVATOR NC5 Configuration: 305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY C2.4 Engine Disassembly and Assembly C2.4 Tier 4 Final Engines for Caterpillar Built Machines Media Number -UENR7319-02 Publication Date -01/07/2018 Date Updated -01/08/2018 i06512587 Water Pump - Remove and Install SMCS - 1361-011; 1361-012 Removal Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Dispose of all fluids according to local regulations and mandates. 1. Drain the coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct draining and filling procedures. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/2/7

305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY ... 2/3 Illustration 1 g06003853 2. Remove bolts (2), suction fan (1), and the fan spacer. Illustration 2 g06003869 3. Loosen bolt (5), the bolts, and the bracket assembly (not shown). Move alternator (4) and remove belt (6) . 4. Remove pulley (3). Illustration 3 g06003956 5. Remove clamp (10) and hose assembly (9). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/2/7

305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY ... 3/3 6. Remove nut (7), bolts (8), water pump (11), and the gasket. Installation Procedure 1. Install water pump (11) in the reverse order of removal. Copyright 1993 - 2020 Caterpillar Inc. Fri Feb 7 23:16:13 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/2/7

305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY ... 1/2 Shutdown SIS Previous Screen Product: MINI HYD EXCAVATOR Model: 305.5E2 CR MINI HYD EXCAVATOR NC5 Configuration: 305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY C2.4 Engine Disassembly and Assembly C2.4 Tier 4 Final Engines for Caterpillar Built Machines Media Number -UENR7319-02 Publication Date -01/07/2018 Date Updated -01/08/2018 i06515139 Water Temperature Regulator - Remove and Install SMCS - 1355-010 Removal Procedure Table 1 Required Tooling Tool Part Number Part Description Qty A - Loctite 5009 Hi-Tack Gasket Sealant - NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Dispose of all fluids according to local regulations and mandates. 1. Drain the coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct draining and filling procedures. Note: Coolant only needs drained to below the water temperature regulator. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/2/7

305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY ... 2/2 Illustration 1 g06005501 2. Remove bolts (1), cover (2), and the gasket. Illustration 2 g06005531 3. Remove water temperature regulator (3). Installation Procedure 1. Install water temperature regulator (3) in the reverse order of removal. a. Apply Tooling (A) to cover (2). Copyright 1993 - 2020 Caterpillar Inc. Fri Feb 7 23:17:10 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/2/7

305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY ... 1/3 Shutdown SIS Previous Screen Product: MINI HYD EXCAVATOR Model: 305.5E2 CR MINI HYD EXCAVATOR NC5 Configuration: 305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY C2.4 Engine Disassembly and Assembly C2.4 Tier 4 Final Engines for Caterpillar Built Machines Media Number -UENR7319-02 Publication Date -01/07/2018 Date Updated -01/08/2018 i06577986 Water Temperature Regulator - Remove and Install SMCS - 1355-010 Removal Procedure NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. 1. Drain the coolant to a level that is below the water temperature regulator. Refer to "Operation and Maintenance Manual", Cooling System Coolant (ELC) - Change for the correct draining procedure. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/2/7

305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY ... 2/3 Illustration 1 g06030443 2. Loosen clamp (1) and disconnect hose (3). Remove two bolts (4). Remove cover (2) and the gasket. Illustration 2 g06030492 3. Remove water temperature regulator (5). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/2/7

Suggest: If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading

305.5E2 CR Mini Hydraulic Excavator NC500001-UP (MACHINE) POWERED BY ... 3/3 Installation Procedure 1. Install water temperature regulator (5) in the reverse order of removal. Copyright 1993 - 2020 Caterpillar Inc. Fri Feb 7 23:18:07 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/2/7

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com