Caterpillar Cat 226 Skid Steer Loader (Prefix 5FZ) Service Repair Manual Instant Download

Service Repair Manual Model 226 Skid SteerLoader

216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024... 1/4 Shutdown SIS Previous Screen Product: SKID STEER LOADER Model: 226 SKID STEER LOADER 5FZ Configuration: 216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024C, 3034 Engine Disassembly and Assembly 216, 226, 232 and 242 Skid Steer Loaders Machine Systems Media Number -RENR4838-02 Publication Date -01/11/2009 Date Updated -04/11/2009 i01671430 Tilt Cylinder - Remove SMCS - 5104-011 S/N - 4NZ3400-UP S/N - 5FZ6700-UP Removal Procedure Table 1 REQUIRED TOOLS Tool Part Number Part Description Qty A 1U-9759 Jack Stand 2 B 1U-9760 Jack Stand 2 Start By: A. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release". B. Remove the quick coupler. Refer to Disassembly and Assembly, "Quick Coupler - Remove and Install". Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/10

216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024... 2/4 Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. Note: Put identification marks on all lines and on all cylinders for installation purposes. Plug all lines. This will help to prevent fluid loss and this helps to keep contaminants from entering the system. Illustration 1 g00593382 1. Use Tooling (A) to support the rear of the machine. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/10

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com

216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024... 3/4 Illustration 2 g00593394 Illustration 3 g00593397 2. Remove snap ring (1) from the front of each lift cylinder. 3. Remove pin (2) from the front of each lift cylinder. Illustration 4 g00684652 4. Attach a suitable lifting device in order to raise the lift arm assembly. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/10

216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024... 4/4 5. Use Tooling (B) in order to support lift arm assembly (3) . Illustration 5 g00684660 6. Disconnect lines (4) and (5) from each tilt cylinder. Illustration 6 g00684669 7. Remove nut (7) and bolt (6) . 8. Remove pin (8) from the tilt cylinder. 9. Remove the tilt cylinder from the lift arm assembly (9) . 10. Repeat Steps 7 through 9 for the opposite side. Copyright 1993 - 2019 Caterpillar Inc. Thu Oct 10 12:59:53 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/10

216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024... 1/4 Shutdown SIS Previous Screen Product: SKID STEER LOADER Model: 226 SKID STEER LOADER 5FZ Configuration: 216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024C, 3034 Engine Disassembly and Assembly 216, 226, 232 and 242 Skid Steer Loaders Machine Systems Media Number -RENR4838-02 Publication Date -01/11/2009 Date Updated -04/11/2009 i01674277 Tilt Cylinder - Install SMCS - 5104-012 S/N - 4NZ3400-UP S/N - 5FZ6700-UP Installation Procedure Table 1 REQUIRED TOOLS Tool Part Number Part Description Qty A 1U-9759 Jack Stand 2 B 1U-9760 Jack Stand 2 Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/10

216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024... 2/4 NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. Illustration 1 g00684669 1. Position the tilt cylinder into lift arm assembly (9) . 2. Install pin (8) into the tilt cylinder. 3. Install bolt (6) and nut (7). Tighten the bolt to a torque of 28 7 N m (21 5 lb ft). 4. Repeat Steps 1 through 3 for the opposite side. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/10

216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024... 3/4 Illustration 2 g00684660 5. Connect lines (4) and (5) to each tilt cylinder. Illustration 3 g00684652 6. Use a suitable lifting device to lift the lift arm assembly upward. 7. Remove Tooling (B) from the lift arm assembly (3) . 8. Use a suitable lifting device to lower the lift arm assembly. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/10

216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024... 4/4 Illustration 4 g00593394 9. Install pin (2) into each of the lift cylinder. 10. Install snap ring (1) onto the pin of each lift cylinder. Illustration 5 g00593382 11. Remove Tooling (A) from the rear of the machine. 12. Check the hydraulic oil level. Refer to Operation and Maintenance Manual, SEBU7468, "Hydraulic System Oil Level - Check". End By: Install the quick coupler. Refer to Disassembly and Assembly, "Quick Coupler - Remove and Install". Copyright 1993 - 2019 Caterpillar Inc. Thu Oct 10 13:00:52 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/10

216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024... 1/4 Shutdown SIS Previous Screen Product: SKID STEER LOADER Model: 226 SKID STEER LOADER 5FZ Configuration: 216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024C, 3034 Engine Disassembly and Assembly 216, 226, 232 and 242 Skid Steer Loaders Machine Systems Media Number -RENR4838-02 Publication Date -01/11/2009 Date Updated -04/11/2009 i01526349 Lift Cylinder - Remove SMCS - 5102-011 S/N - 4NZ3400-UP S/N - 5FZ6700-UP Removal Procedure Start By: A. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release". B. Tilt the cab. Refer to Disassembly and Assembly, "Cab -Tilt". Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. NOTICE https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/10

216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024... 2/4 Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. Note: Put identification marks on all lines and on all cylinders for installation purposes. Plug all lines. This will help to prevent fluid loss and this helps to keep contaminants from entering the system. Illustration 1 g00792871 1. Disconnect lines (1) and (2) . 2. Remove retaining pin (3) and lower the loader lift arm brace onto the lift cylinder. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/10

216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024... 3/4 Illustration 2 g00792879 3. Attach a suitable lifting device to cylinder assembly (4) . Illustration 3 g00591488 4. Remove snap ring (5) . 5. Remove pin (6) . Illustration 4 g00795160 6. Remove bolt (7) and the washer. 7. Remove pin assembly (8) from the lift cylinder. 8. Remove lift cylinder assembly (4) and the loader lift arm brace. Weight of the lift cylinder and the loader lift arm brace is 32 kg (70 lb). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/10

216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024... 4/4 Illustration 5 g00690798 9. Loosen clamp (10) and remove lines (9) and (11) . 10. Repeat Steps 1 through 9 for the opposite side. Copyright 1993 - 2019 Caterpillar Inc. Thu Oct 10 13:01:52 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/10

216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024... 1/3 Shutdown SIS Previous Screen Product: SKID STEER LOADER Model: 226 SKID STEER LOADER 5FZ Configuration: 216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024C, 3034 Engine Disassembly and Assembly 216, 226, 232 and 242 Skid Steer Loaders Machine Systems Media Number -RENR4838-02 Publication Date -01/11/2009 Date Updated -04/11/2009 i01586658 Lift Cylinder - Install SMCS - 5102-012 S/N - 4NZ3400-UP S/N - 5FZ6700-UP Installation Procedure Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/10

216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024... 2/3 before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. Illustration 1 g00690798 1. Install line (9) and line (11) . 2. Tighten clamp (10) . Illustration 2 g00795160 3. Attach a suitable lifting device to lift cylinder assembly (4). The weight of the lift cylinder assembly is 32 kg (70 lb). 4. Position the lift cylinder assembly and the loader lift arm brace on the machine. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/10

216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024... 3/3 5. Install pin assembly (8), the washer, and bolt (7) . Illustration 3 g00591488 6. Install pin (6) and snap ring (5) . Illustration 4 g00792871 7. Connect lines (1) and (2) . 8. Raise the loader lift arm brace and install retaining pin (3) . 9. Repeat steps 1 through 8 for the lift cylinder on the opposite side. 10. Check hydraulic oil level. Refer to Operation and Maintenance Manual, SEBU7468, "Hydraulic System Oil Level - Check". Copyright 1993 - 2019 Caterpillar Inc. Thu Oct 10 13:02:51 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/10

216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024... 1/5 Shutdown SIS Previous Screen Product: SKID STEER LOADER Model: 226 SKID STEER LOADER 5FZ Configuration: 216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024C, 3034 Engine Disassembly and Assembly 216, 226, 232 and 242 Skid Steer Loaders Machine Systems Media Number -RENR4838-02 Publication Date -01/11/2009 Date Updated -04/11/2009 i01545307 Lift Arms - Remove SMCS - 6119-011 S/N - 4NZ3400-UP S/N - 5FZ6700-UP Removal Procedure Start By: A. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release". B. Remove the quick coupler. Refer to Disassembly and Assembly, "Quick Coupler - Remove and Install". C. Remove the tilt cylinder. Refer to Disassembly and Assembly, "Tilt Cylinder - Remove". D. Tilt the cab. Refer to Disassembly and Assembly, "Cab-Tilt". Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/10

216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024... 2/5 NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. Note: Put identification marks on all lines and on all wires for installation purposes. Plug all lines. This will help to prevent fluid loss and this helps to keep contaminants from entering the system. 1. Open the engine access door. Illustration 1 g00594375 2. Remove strap (1) and disconnect harness (2) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/10

216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024... 3/5 Illustration 2 g00589421 3. Remove two bolts (3) and washers from the bracket. Move bracket (4) with the harness aside. Illustration 3 g00593552 4. Disconnect lines (5) and (6) from the lift arm assembly. 5. Repeat step 4 on the opposite side. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/10

216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024... 4/5 Illustration 4 g00790815 6. Remove snap ring (7) from the rod end of the cylinder. 7. Remove pin (8) . 8. Repeat steps 6 and 7 for the opposite side. Illustration 5 g00790823 9. Remove two bolts (9) and two clips (10) from the lines under the lift arm assembly. 10. Repeat step 9 for the opposite side of the lift arm assembly. Illustration 6 g00790828 11. Remove two bolts (11), two clips (12), and the line assemblies from the underside of the lift arm assembly. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/10

216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024... 5/5 Illustration 7 g00593621 12. Use a suitable lifting device to support the lift arms. Illustration 8 g00790831 13. Remove bolt (13) and pin assembly (14) from both sides of the lift arm assembly. 14. Remove the lift arm assembly from the machine. The weight of the lift arm assembly is 322 kg (710 lb). Copyright 1993 - 2019 Caterpillar Inc. Thu Oct 10 13:03:50 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/10

216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024... 1/5 Shutdown SIS Previous Screen Product: SKID STEER LOADER Model: 226 SKID STEER LOADER 5FZ Configuration: 216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024C, 3034 Engine Disassembly and Assembly 216, 226, 232 and 242 Skid Steer Loaders Machine Systems Media Number -RENR4838-02 Publication Date -01/11/2009 Date Updated -04/11/2009 i01545394 Lift Arms - Install SMCS - 6119-012 S/N - 4NZ3400-UP S/N - 5FZ6700-UP Installation Procedure Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/10

216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024... 2/5 before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. Illustration 1 g00593621 1. Attach a suitable lifting device to the lift arm assembly in order to position the lift arm assembly to the machine. The weight of the lift arm assembly is 322 kg (710 lb). Illustration 2 g00790831 2. Install pin assembly (14) and bolt (13) to both sides of the lift arm assembly. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/10

Suggest: If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading

216 226 232 242 Skid Steer Loader 5FZ06700-UP (MACHINE) POWERED BY 3024... 3/5 Illustration 3 g00790828 3. Position the line assemblies on the underside of the lift arm assembly. Install two clips (12) and two bolts (11) . Illustration 4 g00790823 4. Install two clips (10) and two bolts (9) on the lines under the lift arms. 5. Repeat step 4 for the opposite side of the lift arm assembly. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/10

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com