Caterpillar Cat 232D Skid Steer Loader (Prefix KXC) Service Repair Manual Instant Download
Please open the website below to get the complete manualnn// n
Download Presentation
Please find below an Image/Link to download the presentation.
The content on the website is provided AS IS for your information and personal use only. It may not be sold, licensed, or shared on other websites without obtaining consent from the author. Download presentation by click this link. If you encounter any issues during the download, it is possible that the publisher has removed the file from their server.
E N D
Presentation Transcript
Service Repair Manual Model 232D Skid SteerLoader
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 1/3 Shutdown SIS Previous Screen Product: SKID STEER LOADER Model: 232D SKID STEER LOADER KXC Configuration: 232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine Disassembly and Assembly C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Media Number -KENR6948-06 Publication Date -01/06/2015 Date Updated -02/08/2018 i06720081 Flywheel - Remove SMCS - 1156-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 138-7573 Link Bracket 1 Guide Stud (M10 x 1.25 mm by 80mm) B - 2 Start By: a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Note: The three cylinder and the four cylinder engines have different flywheels. The removal procedure is similar for all models. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 2/3 Illustration 1 g01305297 Typical example 1. Install Tooling (A) and a suitable lifting device to flywheel (2). The weight of the flywheel is approximately 42 kg (93 lb). 2. Remove two bolts (1) from positions (X) on the flywheel. 3. Install Tooling (B) in positions (X) on the flywheel. 4. Remove the remaining bolts (1) and remove flywheel (2). Note: On some three cylinder engines, a roll pin is located between the crankshaft and the flywheel. 5. Inspect ring gear (3) and flywheel (2) for wear or damage. If the ring gear or the flywheel is worn or damaged, use new parts for replacement. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 3/3 Illustration 2 g00825639 Typical example 6. To remove ring gear (3) from flywheel (2), place the flywheel on a suitable support. Use a hammer (not shown) and a punch (4) to remove the ring gear from the flywheel. Copyright 1993 - 2019 Caterpillar Inc. Thu Oct 3 21:43:14 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 1/4 Shutdown SIS Previous Screen Product: SKID STEER LOADER Model: 232D SKID STEER LOADER KXC Configuration: 232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine Disassembly and Assembly C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Media Number -KENR6948-06 Publication Date -01/06/2015 Date Updated -02/08/2018 i06720105 Flywheel - Install SMCS - 1156-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 138-7573 Link Bracket 1 Guide Stud (M10 x 1.25 mm by 80mm) B - 2 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Always wear protective gloves when handling parts that have been heated. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 2/4 Illustration 1 g01305341 Typical example 1. If the ring gear was removed, follow Steps 1.a through 1.c to install ring gear (3) to flywheel (2). a. Identify the orientation of the new ring gear to install the ring gear correctly onto the flywheel. Note: The chamfered side of gear teeth (Y) must face toward the starting motor when the flywheel is installed to ensure the correct engagement of the starting motor. b. Heat ring gear (3) in an oven to a maximum temperature of 150 C (302 F) prior to installation. Note: Do not use a torch to heat the ring gear. c. Ensure that ring gear (3) is correctly oriented and quickly install the ring gear onto flywheel (2). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 3/4 Illustration 2 g01305297 Typical example 2. Thoroughly clean the flywheel housing. Inspect the crankshaft rear seal for leaks. If there are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove and Install". 3. Install Tooling (B) to positions (X) in the crankshaft. 4. Install Tooling (A) and a suitable lifting device to flywheel (2). The weight of the flywheel is approximately 42 kg (93 lb). 5. On three cylinder engines with a roll pin, ensure that the roll pin is installed to the crankshaft. Ensure that the roll pin is free from damage. Align the hole in the flywheel with the roll pin in the crankshaft. Position flywheel (2) onto Tooling (B). 6. Install bolts (1) finger tight. 7. Remove Tooling (B) and install the two remaining bolts (1). 8. Use a suitable tool to prevent flywheel (2) from rotating. Tighten bolts (1) to a torque of 74 N m (54 lb ft). 9. Remove Tooling (A) and the lifting device from the flywheel. End By: https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 4/4 a. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install". Copyright 1993 - 2019 Caterpillar Inc. Thu Oct 3 21:44:13 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 1/4 Shutdown SIS Previous Screen Product: SKID STEER LOADER Model: 232D SKID STEER LOADER KXC Configuration: 232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine Disassembly and Assembly C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Media Number -KENR6948-06 Publication Date -01/06/2015 Date Updated -02/08/2018 i07360167 Crankshaft Rear Seal - Remove and Install SMCS - 1161-010 Removal Procedure Start By: a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Dispose of all fluids according to local regulations and mandates. Note: The three cylinder and the four cylinder engines have different configurations for the flywheel housing and the back plate. The removal process is similar for all models. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 2/4 Illustration 1 g01305376 Typical example 1. Remove bolts (3) and remove the flywheel housing or back plate (2) from the cylinder block. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install" for more information. 2. Remove crankshaft rear seal (1) from the cylinder block. Discard the crankshaft oil seal. Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 4C-9612 Silicone Sealant 1 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 3/4 Illustration 2 g01305365 Typical example 1. Ensure the mating surface of cylinder block (5) and the flywheel housing or back plate (2) are clean and free from damage. Inspect dowels (4). If the dowels are damaged, use new parts for replacement. 2. Ensure that crankshaft flange (6) is clean and free from damage. A crankshaft flange that has a worn seal surface, or a damaged seal surface can be reclaimed by installing a wear sleeve. Refer to Disassembly and Assembly, "Crankshaft Wear Sleeve (Rear) - Remove and Install" for more information. 3. Apply clean engine lubricating oil to the flange of crankshaft (6) around the running surface of crankshaft rear seal. 4. Align a new crankshaft rear seal (1) with the flange of crankshaft (6). Carefully install crankshaft rear seal (1) onto the crankshaft flange. 5. Apply a continuous bead of Tooling (A) to the rear face of the cylinder block around the edge of crankshaft rear seal (1). Apply a continuous bead of Tooling (A) around plug (X). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 4/4 6. Align the flywheel housing or back plate (2) to dowels (4). Install the flywheel housing or back plate (2) and install bolts (3) to cylinder block (5). Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install" for more information. 7. Tighten bolts (3). For the C1.1 engine, tighten the bolts to a torque of 50 N m (37 lb ft). For C1.5 and C2.2 engines, tighten the bolts to a torque of 25 N m (221 lb in). End By: a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install". Copyright 1993 - 2019 Caterpillar Inc. Thu Oct 3 21:45:12 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 1/6 Shutdown SIS Previous Screen Product: SKID STEER LOADER Model: 232D SKID STEER LOADER KXC Configuration: 232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine Disassembly and Assembly C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Media Number -KENR6948-06 Publication Date -01/06/2015 Date Updated -02/08/2018 i06042230 Crankshaft Wear Sleeve (Rear) - Remove and Install SMCS - 1161-010-ZV Removal Procedure Start By: a. Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove and Install" for the correct procedure. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Note: Wear sleeves are used to reclaim worn seal surfaces or damaged seal surfaces. Wear sleeves are not original equipment. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 2/6 Illustration 1 g03786380 Sectional view of the crankshaft and of the crankshaft wear sleeve 1. Use a suitable sharp tool to score a deep line across crankshaft wear sleeve (1). Note: Some crankshaft wear sleeves may have a flange. Take care to avoid damaging the crankshaft. 2. Insert a thin blade between crankshaft wear sleeve (1) and crankshaft (2) below the scored line. The crankshaft wear sleeve will separate along the line. 3. Remove crankshaft wear sleeve (1) from crankshaft (2). Discard the crankshaft wear sleeve. Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 1U-8846 Gasket Maker 1 NOTICE https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 3/6 Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Ensure that the crankshaft is thoroughly clean and dry. Remove any areas of raised damage. Illustration 2 g03786381 Sectional view of the wear sleeve https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 4/6 Illustration 3 g03786382 Sectional view of the crankshaft, the wear sleeve, and the installation tool https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 5/6 Illustration 4 g03786398 2. Apply a small continuous bead of Tooling (A) to the inner surface of crankshaft wear sleeve (1) at position X. Apply the bead of Tooling (A) 5.00 mm (0.2 inch) from the flange end of the crankshaft wear sleeve. 3. Align crankshaft wear sleeve (1) with crankshaft (2). Position installation tool (3) that is provided with the crankshaft wear sleeve over the crankshaft. Use a hammer to drive the crankshaft wear sleeve onto the crankshaft. Ensure that dimension (Y) is 6.5 mm (0.26 inch). Note: Dimension (Y) is the distance from the edge of the crankshaft wear sleeve from the rear face of the crankshaft. 4. Remove installation tool (3). 5. Use a suitable tool to cut down to Scored Line (Z) on crankshaft wear sleeve (1) and remove the curved section of the crankshaft wear sleeve.Ensure that the crankshaft rear seal https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 6/6 surface of the crankshaft wear sleeve is not distorted or damaged as the curved section of the crankshaft wear sleeve is removed. Note: Ensure that the crankshaft wear sleeve has no rough edges, if crankshaft wear sleeve has rough edges use suitable tooling to clean the rough edges. End By: a. Install a new crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove and Install" for the correct procedure. Copyright 1993 - 2019 Caterpillar Inc. Thu Oct 3 21:46:11 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 1/5 Shutdown SIS Previous Screen Product: SKID STEER LOADER Model: 232D SKID STEER LOADER KXC Configuration: 232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine Disassembly and Assembly C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Media Number -KENR6948-06 Publication Date -01/06/2015 Date Updated -02/08/2018 i02602665 Flywheel Housing - Remove and Install - Engines with Flywheel Housing and Back Plate SMCS - 1157-010 Removal Procedure Start By: a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Support the engine. 2. Install a suitable lifting device to the flywheel housing. Support the weight of the housing. The weight of the flywheel housing is approximately 30 kg (66 lb). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 2/5 Illustration 1 g01326591 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 3/5 Illustration 2 g01305649 Typical example 3. Remove bolts (3) and (4) that fasten flywheel housing (8) to the cylinder block. 4. Remove bolts (6) on each side of the cylinder block. These bolts fasten flywheel housing (8) to the cylinder block. 5. Remove bolts (1) that fasten back plate (2) to flywheel housing (8). 6. Remove nuts (5) and the bolts (not shown) that fasten back plate (2) to flywheel housing (8). 7. Carefully remove flywheel housing (8) from back plate (2) and dowels (7). Use a suitable lifting device to remove the flywheel housing. Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 4/5 1. Ensure that the mating surfaces of back plate (2) and flywheel housing (8) are clean and free from damage. Inspect the crankshaft rear seal (not shown) for leaks. If necessary, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove and Install" for the correct procedure. Inspect dowels (7) for damage. If the dowels are damaged, use new parts for replacement. Illustration 3 g01305649 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 5/5 Illustration 4 g01326591 Typical example 2. Use a suitable lifting device to align flywheel housing (8) to dowels (7). The weight of the flywheel housing is approximately 30 kg (66 lb). Install the flywheel housing to the back plate. 3. Install nuts (5) and the bolts (not shown) that fasten back plate (2) to flywheel housing (8). 4. Install bolts (1) that fasten back plate (2) to flywheel housing (8). 5. Install bolts (6) on each side of the cylinder block. These bolts fasten flywheel housing (8) to the cylinder block. 6. Remove the lifting device from the flywheel housing. 7. Install bolts (3) and (4) that fasten flywheel housing (8) to the cylinder block. 8. Tighten the fasteners to a torque of 25 N m (19 lb ft). End By: a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install". Copyright 1993 - 2019 Caterpillar Inc. Thu Oct 3 21:47:11 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 1/3 Shutdown SIS Previous Screen Product: SKID STEER LOADER Model: 232D SKID STEER LOADER KXC Configuration: 232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine Disassembly and Assembly C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Media Number -KENR6948-06 Publication Date -01/06/2015 Date Updated -02/08/2018 i06721519 Flywheel Housing - Remove and Install SMCS - 1157-010 Removal Procedure Start By: a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Note: The three cylinder and the four cylinder engines have different flywheel housings. The removal procedure is similar for all models. 1. Support the engine. 2. Install a suitable lifting device to the flywheel housing. Support the weight of the housing. The weight of the flywheel housing is approximately 30 kg (66 lb). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 2/3 Illustration 1 g01305734 Typical example 3. Remove bolts (1) that fasten flywheel housing (2) to the cylinder block. 4. Use the lifting device to remove flywheel housing (2) from the engine. Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
Suggest: If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S... 3/3 Illustration 2 g01326595 Typical example 1. Ensure the mating surfaces of flywheel housing (2) are clean and free from damage. Inspect the crankshaft rear seal (3) for leaks. If necessary, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove and Install" for the correct procedure. Inspect dowels (4) for damage. If the dowels are damaged, use new parts for replacement. 2. Use a suitable lifting device to align flywheel housing (2) to dowels (5) and install the flywheel housing. The weight of the flywheel housing is approximately 30 kg (66 lb). 3. Install bolts (1). Tighten the bolts to a torque of 25 N m (19 lb ft). 4. Remove the lifting device from the flywheel housing. End By: a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install". Copyright 1993 - 2019 Caterpillar Inc. Thu Oct 3 21:48:10 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/3
https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com
