Caterpillar Cat 321D LCR EXCAVATOR (Prefix MDT) Service Repair Manual Instant Download
Please open the website below to get the complete manualnn//
Download Presentation
Please find below an Image/Link to download the presentation.
The content on the website is provided AS IS for your information and personal use only. It may not be sold, licensed, or shared on other websites without obtaining consent from the author. Download presentation by click this link. If you encounter any issues during the download, it is possible that the publisher has removed the file from their server.
E N D
Presentation Transcript
Service Repair Manual Model 321DLCR EXCAVATOR
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 1/5 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 321D LCR EXCAVATOR MDT Configuration: 321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine Disassembly and Assembly C6.4 Engine for Caterpillar Built Machines Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017 i04786161 Fuel Injection Pump - Install SMCS - 1251-012 Installation Procedure Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times. Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 2/5 Illustration 1 g01375221 Illustration 2 g02723322 (2) Fuel injection pump drive gear (3) Idler gear Note: Align timing marks on pump drive gear (2) and idler gear (3) that were made in the removal procedure 1. Position the O-ring seal and fuel injection pump (21) . 2. If you are reusing pump drive gear (2) , align the marks on pump drive gear (2) and idler gear (3) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 3/5 3. If replacing the pump drive gear or a problem is encountered, refer to Testing and Adjusting, "Fuel Injection Timing-Check" for the correct procedure. 4. Install bolts (24) . 5. Install two bolts (23) (not shown). 6. Install bolts (22) . Illustration 3 g01375105 7. Install cover (1) . Illustration 4 g01375184 8. Install new washers and tube assembly (10) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 4/5 9. Install new washers and connect hose assembly (18) . Install bolt (19) . Tighten bolt (19) to a torque of 34 4 N m (25 3 lb ft). 10. Install new washers and install hose assembly (17) . Install bolt (16) . Tighten bolt (16) to a torque of 34 4 N m (25 3 lb ft). 11. Connect harness assembly (15) . 12. Install tube assembly (14) . Tighten each end of tube assembly (14) to a torque of 41 5 N m (30 4 lb ft). Illustration 5 g01375195 13. Install new washers and connect tube assembly (10) . Install fitting (11) . Tighten fitting (11) to a torque of 25 + 3 - 0 N m (18 + 2 - 0 lb ft). 14. Connect hose (13) and tighten clamp (12) . Illustration 6 g01375153 15. Install bracket assembly (8) and tube assembly (9) . Tighten each end of tube assembly (9) to a torque of 19 5 N m (14 4 lb ft). 16. Connect harness assembly (7) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 5/5 17. Install new washers and connect hose assemblies (6) . 18. Install nut (5) . Tighten nut (5) to a torque of 34 4 N m (25 3 lb ft). 19. Connect hose (4) . End By: Install the fan drive. Refer to Disassembly and Assembly, "Fan Drive - Remove and Install". Copyright 1993 - 2019 Caterpillar Inc. Mon Oct 7 16:15:03 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 1/3 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 321D LCR EXCAVATOR MDT Configuration: 321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine Disassembly and Assembly C6.4 Engine for Caterpillar Built Machines Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017 i02746250 Fuel Injection Pump Gear - Remove SMCS - 1251-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 5F-7465 Puller Gp 1 Start By: a. Remove the fan drive. Refer to Disassembly and Assembly, "Fan Drive - Remove". b. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 2/3 before opening any compartment or disassembling any component containing fluids. Dispose of all fluids according to local regulations and mandates. Illustration 1 g01375404 1. Remove nut (1). Illustration 2 g01375405 2. Use Tooling (A) in order to remove fuel injection pump gear (2). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 3/3 Illustration 3 g01375406 3. Remove key (3). Copyright 1993 - 2019 Caterpillar Inc. Mon Oct 7 16:15:59 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 1/2 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 321D LCR EXCAVATOR MDT Configuration: 321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine Disassembly and Assembly C6.4 Engine for Caterpillar Built Machines Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017 i04762770 Fuel Injection Pump Gear - Install SMCS - 1251-012 Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 1 g01375406 1. Install key (3) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 2/2 Illustration 2 g01375407 Note: The use of a soft jaw vice is to keep fuel injection pump gear (2) stationary to tighten nut (1) . 2. Place fuel injection pump gear (2) into a soft jaw vice. Tighten nut (1) to a torque of 90 6 N m (66 4 lb ft). End By: a. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Install". b. Install the fan drive. Refer to Disassembly and Assembly, "Fan Drive - Install". Copyright 1993 - 2019 Caterpillar Inc. Mon Oct 7 16:16:55 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 1/3 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 321D LCR EXCAVATOR MDT Configuration: 321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine Disassembly and Assembly C6.4 Engine for Caterpillar Built Machines Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017 i02746266 Electronic Unit Injector - Remove SMCS - 1290-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 5F-4764 Pry Bar 1 B 278-4138 Fuel System Protection Gp(1) 1 (1)This tool can only be used one time. Start By: a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install". b. Remove the fuel Injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove". NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 2/3 Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Do not open the high pressure fuel system without allowing the fuel system to purge. After the engine has shut down, allow the fuel system to purge for ten minutes. This operating fuel system contains high pressure. Exposure to high pressure fuel can result in personal injury. Note: Before opening the fuel system, the engine must be turned off for at least one minute. Note: Use Caterpillar Electronic Technician (ET) to verify that the fuel system pressure is at zero before opening the fuel system. Note: Use Tooling (B) after any fuel line has been disconnected. Note: Cleanliness is an important factor. Before you begin the removal procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism. Note: Put identification marks on harness assemblies and electronic unit injectors for installation purposes. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 3/3 Illustration 1 g01375478 1. Loosen nuts (2). 2. Disconnect harness assembly (1). Illustration 2 g01375483 3. Remove bolt (3) and the washer. 4. Place an identification mark on electronic unit injector (4) for installation purposes. Each electronic unit injector must be reinstalled in the original location. Use Tooling (A) in order to remove electronic unit injector (4). 5. Remove clamp (5) (not shown). 6. Repeat Steps 1 through 5 for the remaining electronic unit injectors. Copyright 1993 - 2019 Caterpillar Inc. Mon Oct 7 16:17:51 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 1/2 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 321D LCR EXCAVATOR MDT Configuration: 321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine Disassembly and Assembly C6.4 Engine for Caterpillar Built Machines Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017 i05281314 Electronic Unit Injector - Install SMCS - 1290-012 Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 1 g01375483 1. Install a new O-ring and a new copper washer onto the electronic unit injector (not shown). Install clamp (5) (not shown) onto electronic unit injector (4) . Install electronic unit injector (4) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 2/2 2. Install bolt (3) and the washer. Note: Note the orientation of the washer for installation. Illustration 2 g01375478 3. Connect harness assembly (1) and tighten nuts (2) to a torque of 2.5 N m (22 lb in). 4. Repeat Steps 1 through 3 for the remaining electronic unit injectors. End By: a. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove". b. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install". Copyright 1993 - 2019 Caterpillar Inc. Mon Oct 7 16:18:46 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 1/2 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 321D LCR EXCAVATOR MDT Configuration: 321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine Disassembly and Assembly C6.4 Engine for Caterpillar Built Machines Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017 i02747029 Turbocharger - Remove SMCS - 1052-011 Removal Procedure Illustration 1 g01375920 1. Loosen clamp (1). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 2/2 Illustration 2 g01375922 Typical Example 2. Remove nuts (4) and tube (6). Disconnect tube assemblies (2) and (7). Disconnect hoses (5) and (9). Remove nuts (8) and turbocharger (3). Copyright 1993 - 2019 Caterpillar Inc. Mon Oct 7 16:19:42 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 1/3 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 321D LCR EXCAVATOR MDT Configuration: 321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine Disassembly and Assembly C6.4 Engine for Caterpillar Built Machines Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017 i02746993 Turbocharger - Disassemble SMCS - 1052-015 Disassembly Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 1P-1861 Retaining Ring Pliers 1 Start By: a. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 2/3 Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. 1. Place an index mark on all of the components. The marks will help to align the components during the assembly procedure. Illustration 1 g01375875 2. Remove gasket (1) from the cartridge. 3. Remove gasket (2) from the turbine housing. Illustration 2 g01375876 4. Remove the bolt and nut (3) from clamp (4). Remove clamp (4) that secures turbine housing (5) to cartridge (6). 5. Separate turbine housing (5) fromcartridge (6). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 3/3 Illustration 3 g01375877 Illustration 4 g01375878 6. Use Tooling (A) in order to remove retaining ring (7) from compressor housing (8). 7. Separate compressor housing (8) from cartridge (6). Copyright 1993 - 2019 Caterpillar Inc. Mon Oct 7 16:20:38 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 1/3 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 321D LCR EXCAVATOR MDT Configuration: 321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine Disassembly and Assembly C6.4 Engine for Caterpillar Built Machines Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017 i02747012 Turbocharger - Assemble SMCS - 1052-016 Assembly Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 1P-1861 Retaining Ring Pliers 1 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Note: During the assembly procedure, ensure that the index marks are aligned when the components are assembled. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 2/3 Illustration 1 g01375878 Illustration 2 g01375877 1. Install cartridge (6) into compressor housing (8). 2. Use Tooling (A) in order to install retaining ring (7) into compressor housing (8). Illustration 3 g01375876 3. Install cartridge (6) into turbine housing (5). 4. Install clamp (4) that secures cartridge (6) and turbine housing (5) together. Install the bolt and nut (3) into clamp (4). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 3/3 Note: Refer to the Specifications Module , "Turbocharger" for information on the clamp. Illustration 4 g01375875 5. Inspect the condition of the gaskets. Replace the gaskets, if necessary. 6. Install gasket (2) on the turbine housing. 7. Install gasket (1) on the cartridge. End By: a. Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install". Copyright 1993 - 2019 Caterpillar Inc. Mon Oct 7 16:21:34 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
Suggest: If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading
321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine(SE... 1/2 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 321D LCR EXCAVATOR MDT Configuration: 321D LCR Excavator MDT00001-UP (MACHINE) POWERED BY C6.4 Engine Disassembly and Assembly C6.4 Engine for Caterpillar Built Machines Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017 i02747030 Turbocharger - Install SMCS - 1052-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 5P-3931 Anti-Seize Compound 1 Illustration 1 g01375922 Typical Example 1. Install turbocharger (3). Apply Tooling (A) to nuts (8) and install nuts (8). Tighten nuts (8) to a torque of 54 5 N m (40 4 lb ft). Connect hoses (5) and (9). Connect tube assemblies (2) and (7). Install tube (6) and nuts (4). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/7
https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com
