Caterpillar Cat D6K TRACK-TYPE TRACTOR (Prefix NCF) Service Repair Manual Instant Download

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 1/10 Product: TRACK-TYPE TRACTOR Model: D6K TRACK-TYPE TRACTOR NCF Configuration: D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWERED BY C6.6 Engine Disassembly and Assembly C6.6 Engines for Caterpillar Built Machines Media Number -KENR6081-15 Publication Date -01/03/2014 Date Updated -04/03/2014 i06192499 Gear Group (Front) - Remove and Install SMCS - 1206-010 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A (1) 9U-6198 Crankshaft Turning Tool 1 9U-7336 Housing 1 A (2) 5P-7305 Engine Turning Tool 1 B 230-6284 Timing Pin (Camshaft) 1 136-4632 Timing Pin (Crankshaft) 1 C 268-1966 Adapter 1 ( 1 ) The Crankshaft Turning Tool is used on the front pulley. ( 2 ) This Tool is used in the aperture for the electric starting motor. Start By: A. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and Install". B. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install". NOTICE Keep all parts clean from contaminants. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 2/10 Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Dispose of all fluids according to local regulations and mandates. Note: Either Tooling (A) can be used. Use the Tooling that is most suitable. Care must be taken in order to ensure that the fuel injection pump timing is not lost during the removal of the front gear group. Carefully follow the procedure in order to remove the gear group. 1. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead center on the compression stroke. Refer to System Operation, Testing and Adjusting, "Finding Top Center Position for No.1 Piston". https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 3/10 Illustration 1 g01335379 Typical example 2. Install Tooling (B) through hole (X) in camshaft gear (1) into the front housing. Use Tooling (B) in order to lock the camshaft in the correct position. Refer to System Operation, Testing and Adjusting, "Finding Top Center Position for No.1 Piston". Illustration 2 g01335380 3. Remove plug (4) from the cylinder block. Install Tooling (C) into hole (Y) in the cylinder block. Use Tooling (C) in order to lock the crankshaft in the correct position. Refer to System Operation, Testing and Adjusting, "Finding Top Center Position for No.1 Piston". Note: Do not use excessive force to install Tooling (C) . Do not use Tooling (C) to hold the crankshaft during repairs. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 4/10 Illustration 3 g01337898 4. Loosen nuts (6) on all rocker arms (7) . Unscrew adjusters (5) on all rocker arms (7) until all valves are fully closed. Note: Failure to ensure that ALL adjusters are fully unscrewed can result in contact between the valves and pistons. 5. Apply sufficient pressure to fuel injection pump gear (3) in a counterclockwise direction in order to remove the backlash. Lock the fuel injection pump in this position. Refer to Disassembly and Assembly, "Fuel Pump Gear - Remove" for the correct procedure. Illustration 4 g01335384 Typical example https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 5/10 6. Mark gears (1) , (2) and (3) in order to show alignment. Refer to Illustration 4. Note: Identification will ensure that the gears can be installed in the original alignment. 7. Remove fuel pump gear (3) . Refer to Disassembly and Assembly, "Fuel Pump Gear - Remove and Install" for the correct procedure. 8. Remove camshaft gear (1) . Refer to Disassembly and Assembly, "Camshaft Gear - Remove and Install". 9. Remove idler gear (2) . Refer to Disassembly and Assembly, "Idler Gear - Remove and Install". Installation Procedure Table 2 Required Tools Tool Part Number Part Description Qty B 230-6284 Timing Pin (Camshaft) 1 136-4632 Timing Pin (Crankshaft) 1 C 268-1966 Adapter 1 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Note: The fuel injection pump must remain locked until the procedure instructs you to unlock the fuel injection pump. 1. Ensure that number one piston is at top dead center on the compression stroke. Refer to System Operation, Testing and Adjusting, "Finding Top Center for No. 1 Piston". https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 6/10 Illustration 5 g01335380 2. If necessary, install Tooling (C) into hole (Y) in the cylinder block. Use Tooling (C) in order to lock the crankshaft in the correct position. Refer to System Operation, Testing and Adjusting, "Finding Top Center Position for No.1 Piston". Note: Do not use excessive force to install Tooling (C) . Do not use Tooling (C) to hold the crankshaft during repairs. 3. Ensure that all of the components of the front gear group are clean and free from wear of damage. If necessary, replace any components that are worn or damaged. Illustration 6 g01337904 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 7/10 4. Install camshaft gear (1) . Loosely install bolt (6) and washer (5) for the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove and Install" for more information. Illustration 7 g01335379 Typical example 5. Install Tooling (B) through hole (X) in camshaft gear (1) into the front housing. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 8/10 Illustration 8 g01337905 Typical example Illustration 9 g01335384 Alignment of timing marks 6. Install idler gear (2) . Ensure that the timing marks on gear (1) and gear (2) are in alignment and that the mesh of the gears is correct. Refer to Disassembly and Assembly, "Idler Gear - Remove and Install". Check the end play of the idler gear. Refer to Specifications, "Gear Group (Front)" and refer to Disassembly and Assembly, "Idler Gear - Remove and Install" for further information. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 9/10 7. Tighten bolt (6) for the camshaft gear to a torque of 95 N m (70 lb ft). Check the end play of the camshaft gear. Refer to Specifications, "Camshaft" for more information. 8. Ensure that the fuel injection pump is locked in the correct position. Refer to Disassembly and Assembly, "Fuel Injection Pump - Install". 9. Install fuel injection pump gear (3) . Ensure that the timing marks on gear (2) and gear (3) are in alignment. See Illustration 9. Ensure that the mesh of the gears is correct. Refer to Disassembly and Assembly, "Fuel Injection Pump Gear - Install" for more information. 10. Remove Tooling (B) and (C) . Install plug (4) into hole (Y) in the cylinder block. Refer to Illustration 5. Illustration 10 g01335426 Checking backlash 11. Ensure that the backlash for gears (1) , (2) and (3) is within specified values. Refer to Specifications, "Gear Group (Front)" for further information. 12. Lubricate each gear with clean engine oil. 13. Adjust the engine valve lash. Refer to System Operation, Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust". End By: a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install". b. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and Install". https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 1/10 Product: TRACK-TYPE TRACTOR Model: D6K TRACK-TYPE TRACTOR NCF Configuration: D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWERED BY C6.6 Engine Disassembly and Assembly C6.6 Engines for Caterpillar Built Machines Media Number -KENR6081-15 Publication Date -01/03/2014 Date Updated -04/03/2014 i05735237 Idler Gear - Remove SMCS - 1206-011 Removal Procedure (Standard Idler Gear) Table 1 Required Tools Tool Part Number Part Description Qty A 230-6284 Timing Pin (Camshaft) 1 136-4632 Timing Pin (Crankshaft) 1 B 268-1966 Adapter 1 Start By: a. Remove the fuel injection pump gear. Refer to Disassembly and Assembly, "Fuel Pump Gear - Remove" for the correct procedure. b. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install" for the correct procedure. Note: Care must be taken in order to ensure that the fuel injection pump timing is not lost during the removal of the fuel pump gear. Carefully follow the procedure in order to remove the fuel pump gear. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 2/10 Illustration 1 g01337918 Alignment of timing marks 1. Ensure that Tooling (A) is installed into Hole (X) in the camshaft gear. Use Tooling (A) in order to lock the camshaft in the correct position. Note: Ensure that the gears are marked in order to show alignment. Refer to Illustration 1. Illustration 2 g01337919 2. Ensure that Tooling (B) is installed in Hole (Y) in the cylinder block. Use Tooling (B) in order to lock the crankshaft in the correct position. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 3/10 Illustration 3 g01337921 3. Loosen nuts (5) on all rocker arms (6). Unscrew adjusters (4) on all rocker arms (6) until all valves are fully closed. Note: Failure to ensure that ALL adjusters are fully unscrewed can result in contact between the valves and pistons. 4. Mark plate (3) in order to show orientation. Note: Identification will ensure that the plate can be installed in the original orientation. 5. Remove bolts (1). 6. Remove plate (3). Illustration 4 g01337922 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 4/10 7. Remove the assembly of idler gear (2) and hub (7) from the recess in the front housing. Note: The idler gear must be tilted during removal. 8. Remove hub (7) from idler gear (2). Removal Procedure (Early Heavy-Duty Idler Gear) Table 2 Required Tools Tool Part Number Part Description Qty A 230-6284 Timing Pin (Camshaft) 1 136-4632 Timing Pin (Crankshaft) 1 B 268-1966 Adapter 1 Start By: a. Remove the fuel injection pump gear. Refer to Disassembly and Assembly, "Fuel Pump Gear - Remove" for the correct procedure. b. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install" for the correct procedure. Note: Care must be taken in order to ensure that the fuel injection pump timing is not lost during the removal of the fuel pump gear. Carefully follow the procedure in order to remove the fuel pump gear. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Note: The assembly of heavy-duty idler gear is not serviceable. Do not disassemble the heavy- duty idler gear. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 5/10 Illustration 5 g01337924 Alignment of timing marks 1. Ensure that Tooling (A) is installed into hole (X) in the camshaft gear. Use Tooling (A) in order to lock the camshaft in the correct position. Note: Ensure that the gears are marked in order to show alignment. Refer to Illustration 5. Illustration 6 g01337919 2. Ensure that Tooling (B) is installed in hole (Y) in the cylinder block. Use Tooling (B) in order to lock the crankshaft in the correct position. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 6/10 Illustration 7 g01337921 3. Loosen nuts (4) on all rocker arms (5). Unscrew adjusters (3) on all rocker arms (5) until all valves are fully closed. Note: Failure to ensure that ALL adjusters are fully unscrewed can result in contact between the valves and pistons. 4. Remove bolts (1) from the assembly of heavy-duty idler gear (2). Illustration 8 g01337922 5. Remove the assembly of idler gear (2) from the recess in the front housing. Note: The idler gear must be tilted during removal. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 7/10 Removal Procedure (Latest Heavy-Duty Idler Gear) Table 3 Required Tools Tool Part Number Part Description Qty A 230-6284 Timing Pin (Camshaft) 1 136-4632 Timing Pin (Crankshaft) 1 B 268-1966 Adapter 1 Bolt (M8 x 80mm) C - 1 Start By: a. If the engine is equipped with an air compressor, remove the air compressor. Refer to Disassembly and Assembly, "Air Compressor - Remove and Install" for the correct procedure. b. If the engine is equipped with an accessory drive, remove the accessory drive. Refer to Disassembly and Assembly, "Accessory Drive - Remove and Install" for the correct procedure. c. Remove the fuel injection pump gear. Refer to Disassembly and Assembly, "Fuel Pump Gear - Remove" for the correct procedure. d. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install" for the correct procedure. Note: Care must be taken in order to ensure that the fuel injection pump timing is not lost during the removal of the fuel pump gear. Carefully follow the procedure in order to remove the fuel pump gear. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Note: The assembly of heavy-duty idler gear is not serviceable. Do not disassemble the heavy- duty idler gear. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 8/10 Illustration 9 g01343977 Alignment of timing marks 1. Ensure that Tooling (A) is installed into Hole (X) in the camshaft gear. Use Tooling (A) in order to lock the camshaft in the correct position. Note: Ensure that the gears are marked in order to show alignment. Refer to Illustration 9. 2. Ensure that Tooling (B) is installed in Hole (Y) in the front housing. Use Tooling (B) in order to lock the crankshaft in the correct position. Illustration 10 g01337921 Typical example 3. Loosen nuts (5) on all rocker arms (6). Unscrew adjusters (4) on all rocker arms (5) until all valves are fully closed. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 9/10 Note: Failure to ensure that ALL adjusters are fully unscrewed can result in contact between the valves and pistons. 4. Remove bolts (1) from the assembly of heavy-duty idler gear (2). Refer to Illustration 9. Illustration 11 g01269933 Typical example 5. Remove the assembly of idler gear (2) from the recess in the front housing. Note: The idler gear must be tilted during removal. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWE... 10/10 Illustration 12 g01348835 Typical example 6. If necessary, remove plate (6). Install Tooling (C) into threaded Hole (Z) in order to remove plate (6). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 1/13 Product: TRACK-TYPE TRACTOR Model: D6K TRACK-TYPE TRACTOR NCF Configuration: D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWERED BY C6.6 Engine Disassembly and Assembly C6.6 Engines for Caterpillar Built Machines Media Number -KENR6081-15 Publication Date -01/03/2014 Date Updated -04/03/2014 i05735238 Idler Gear - Install SMCS - 1206-012 Installation Procedure (Standard Idler Gear) Table 1 Required Tools Tool Part Number Part Description Qty A 230-6284 Timing Pin (Camshaft) 1 136-4632 Timing Pin (Crankshaft) 1 B 268-1966 Adapter 1 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Ensure that number one piston is at top dead center on the compression stroke. Refer to System Operation, Testing and Adjusting, "Finding Top Center for No. 1 Piston" for the correct procedure. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 2/13 Illustration 1 g01337918 Alignment of timing marks 2. Ensure that Tooling (A) is installed into Hole (X) in camshaft gear (1). Illustration 2 g01337947 3. Ensure that Tooling (B) is installed in Hole (Y) in the cylinder block. Use Tooling (B) in order to lock the crankshaft in the correct position. Refer to System Operation, Testing and Adjusting, "Finding Top Center Position for No.1 Piston" for the correct procedure. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 3/13 Illustration 3 g01337949 4. Clean idler gear (2) and inspect the idler gear for wear or damage. Refer to Specifications, "Gear Group (Front)" for more information. If necessary, replace the idler gear. 5. Clean hub (7) and inspect the hub for wear or damage. Refer to Specifications, "Gear Group (Front)" for more information. If necessary, replace the hub. 6. Lubricate hub (7) with clean engine oil. Slide hub (7) into idler gear (2). Ensure that the timing marks are toward the front of the idler gear. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 4/13 Illustration 4 g01337952 7. Align the timing mark on idler gear (2) with the timing mark on the camshaft gear. Refer to the illustration 1. Install the assembly of idler gear (2) and hub (7) into the recess in the timing case. Ensure that oil Hole (Z) is to the top of the hub. Note: The idler gear must be tilted during installation. Ensure that the holes in the hub are aligned with the holes in the cylinder block. 8. Clean plate (3) and inspect the plate for wear or damage. If necessary, replace the plate. 9. Lubricate plate (3) with clean engine oil. Align the holes in plate (3) with the holes in hub (7). Install the plate in the original orientation. 10. Install bolts (1). 11. Remove Tooling (A) and Tooling (B). Note: Ensure that timing marks are aligned, before removing the Tooling (A) and Tooling (B). 12. Install plug (8) to the cylinder block. Refer to Illustration 2. 13. Tighten bolts (1) to a torque of 44 N m (32 lb ft). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 5/13 Illustration 5 g01337953 Checking end play by using a set of feeler gauge's 14. Use a set of feeler gauge's in order to check the end play for the idler gear. Refer to Specifications, "Gear Group (Front)" for more information. Illustration 6 g01335426 Checking backlash https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 6/13 15. Check the backlash between the idler gear and the camshaft gear. Refer to Specifications, "Gear Group (Front)" for more information. 16. Check the backlash between the idler gear and the crankshaft gear. Refer to Specifications, "Gear Group (Front)" for more information. 17. Lightly lubricate all of the gears with clean engine oil. End By: a. Install the fuel injection pump gear. Refer to Disassembly and Assembly, "Fuel Pump Gear - Install" for the correct procedure. Installation Procedure (Early Heavy-Duty Idler Gear) Table 2 Required Tools Tool Part Number Part Description Qty A 230-6284 Timing Pin (Camshaft) 1 136-4632 Timing Pin (Crankshaft) 1 B 268-1966 Adapter 1 9U-7324 Indicator Bracket 1 7H-1942 Dial Indicator 1 C 3S-3268 Indicator Contact Point 1 7H-1940 Universal Attachment 1 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Ensure that number one piston is at top dead center on the compression stroke. Refer to System Operation, Testing and Adjusting, "Finding Top Center for No. 1 Piston" for the correct procedure. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 7/13 Illustration 7 g01337924 Alignment of timing marks 2. Ensure that Tooling (A) is installed into Hole (X) in the camshaft gear. Illustration 8 g01337954 3. Ensure that Tooling (B) is installed in Hole (Y) in the cylinder block. Use Tooling (B) in order to lock the crankshaft in the correct position. Refer to System Operation, Testing and Adjusting, "Finding Top Center Position for No.1 Piston" for the correct procedure. 4. Clean the assembly of idler gear (2) and inspect the assembly of the idler gear for wear or damage. Refer to Specifications , "Gear Group (Front)" for more information. If necessary, replace the assembly of the idler gear. 5. Lubricate the bearings in the assembly of idler gear (2) with clean engine oil. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 8/13 Illustration 9 g01337922 6. Align the timing mark on idler gear (2) with the timing mark on the camshaft gear. Refer to the illustration 7. Install the assembly of idler gear (2) into the recess in the timing case. Ensure that the identification mark TOP is upward. Note: The idler gear must be tilted during installation. Ensure that the holes in assembly of the idler gear are aligned with the holes in the cylinder block. 7. Install bolts (1). 8. Remove Tooling (A) and Tooling (B). Note: Ensure that timing marks are aligned, before removing the Tooling (A) and Tooling (B). 9. Install plug (6) to the cylinder block. Refer to Illustration 8. 10. Tighten bolts (1) to a torque of 44 N m (32 lb ft). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

Suggest: If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading

D6K TRACK-TYPE TRACTOR Military, XL NCF00001-UP (MACHINE) POWER... 9/13 Illustration 10 g01337957 11. Use Tooling (C) in order to check the end play for the heavy-duty idler gear. Refer to Specifications, "Gear Group (Front)" for more information. Illustration 11 g01335426 Checking backlash https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/8/24

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com