Caterpillar Cat 352F Excavator (Prefix YEG) Service Repair Manual Instant Download

Service Repair Manual Models 352F, 352F-VG Excavator

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP654... 1/13 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 352F-VG EXCAVATOR YEG Configuration: 352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine Disassembly and Assembly 349F and 352F Excavators Machine Systems Media Number -UENR0194-04 Publication Date -01/02/2018 Date Updated -21/02/2018 i07203491 Travel Motor - Disassemble SMCS - 4351-015 Disassemble Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 1P-2420 Transmission Repair Stand 1 B 421-5662 Lifting Eye Assembly 1 154-6182 M12x1.75 mm Forcing Bolt 2 C 6V-8149 M12x1.75 mm Nut 4 5P-8245 M12 Hard Washer 4 - M3x0.5 Threaded Rod 1 D 3K-3068 3 mm Thrust Washer 1 3C-6969 M3x0.5 Nut 2 8T-0276 M8x45mm Bolt 2 E 9M-1974 M8 Hard Washer 2 Start By: a. Remove travel motor. NOTICE https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP654... 2/13 Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. Illustration 1 g06252257 1. Use Tooling (B) and a suitable lifting device to position travel motor (1) in a vertical position on Tooling (A). The weight of travel motor (1) is approximately 136 kg (300 lb). Use Tooling (C) to attach travel motor (1) to Tooling (A). Illustration 2 g06252275 2. Remove plugs (2), plug (3), plug (4), and the O-ring seals. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP654... 3/13 Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. Illustration 3 g06252280 Illustration 4 g06252989 3. Remove plug (6) and the O-ring seal. 4. Remove plug (5), stopper (7), and ball (8). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP654... 4/13 Illustration 5 g06255756 Illustration 6 g06255791 5. Use Tooling (D) and a suitable washer to extract seat (8A). Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP654... 5/13 Illustration 7 g06252992 Illustration 8 g06252996 6. Remove plugs (9) and the O-ring seals. 7. Remove plug (10), spool (11), spring (12), and the O-ring seal. Illustration 9 g06253028 8. Remove plug (13), valve (14) , and the O-ring seals. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP654... 6/13 Illustration 10 g06253047 Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. 9. Remove the top two nuts and washers from Tooling (C). 10. Remove bolts (15). 11. Use Tooling (B) and a suitable lifting device to remove motor head assembly (16). The weight of motor head assembly (16) is approximately 45 kg (100 lb). Remove motor head assembly (16). Illustration 11 g06253060 12. Remove bearing (17) and O-ring seal (18). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP654... 7/13 Illustration 12 g06253330 13. Reinstall the washers and nuts from Tooling (C) that were removed in a previous Step. 14. Remove springs (19), O-ring seal (20), port plate (21), O-ring seal (22), plug (23), and the O -ring seal. Note: Port plate (21) may still be adhered to the bottom of motor head assembly (16). Illustration 13 g06253333 15. Remove orifice (24) and orifice (25). Illustration 14 g06253335 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP654... 8/13 16. Remove plug (26). Illustration 15 g06253475 17. Use Tooling (E) and suitable prying devices to remove piston assembly (27). Illustration 16 g06253502 Illustration 17 g06253508 Typical example. 18. Remove separator plates (28) and friction plates (29). Note the alternating order of separator plates (28) and friction plates (29) for assembly purposes. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP654... 9/13 Illustration 18 g06253734 19. Remove barrel assembly (30). Note: Do not allow the components of barrel assembly (30) to come apart while you remove barrel assembly (30). The components of barrel assembly (30) must be reinstalled into the original positions. Illustration 19 g06253741 20. Remove piston assemblies (31) and retainer (32). Note: Mark the component locations for assembly purposes before you disassemble the barrel assembly. Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP6... 10/13 Illustration 20 g06253748 21. Remove guide (33). Illustration 21 g06253755 22. Remove springs (34). Illustration 22 g06254252 23. Put location marks on swashplate (35) for assembly purposes. Remove swashplate (35). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP6... 11/13 Illustration 23 g06254282 24. Remove snap ring (37) and roller (36). Illustration 24 g06254306 25. Remove keys (38). Illustration 25 g06254363 26. Remove snap ring (40). 27. Use a soft faced hammer to remove shaft assembly (39). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP6... 12/13 Illustration 26 g06254423 28. Remove snap ring (41). 29. Use a suitable press to remove bearing (42) from shaft assembly (39). Illustration 27 g06254449 30. Remove O-ring seal (43) and O-ring seal (44). Illustration 28 g06254465 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP6... 13/13 Illustration 29 g06254467 31. Remove plug (45) and use compressed air to remove piston (46). Illustration 30 g06254480 32. Remove lip seal (47). Copyright 1993 - 2020 Caterpillar Inc. Wed Oct 14 13:49:57 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP654... 1/13 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 352F-VG EXCAVATOR YEG Configuration: 352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine Disassembly and Assembly 349F and 352F Excavators Machine Systems Media Number -UENR0194-04 Publication Date -01/02/2018 Date Updated -21/02/2018 i06563923 Travel Motor - Assemble SMCS - 4351-016 Specifications Illustration 1 g03845362 NOTICE To prevent damage to the motor, the case must be filled with clean hydraulic oil at least to the fill port before operation. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP654... 2/13 Table 1 Specification for 390-1088 Travel Motor Gp Item Qty Part Specification Description 1 1 5P-7684 Plug Torque to 430 40 N m (317 30 lb ft). 6K-6307 O- Ring Seal 2 1 Lubricate with 1U-6396 O-Ring Assembly Compound. Before assembly, lubricate the sliding surfaces of the cam plate (3), the hold-down (4), the pistons (5), the barrel (6) and the shaft (8) lightly with clean hydraulic oil. - - - Length under test force is 19.0 mm (0.75 inch). Test force is 425 43 N (96 10 lb). Free length after test is 22.06 mm (0.869 inch). 124-1561 Brake Spring 7 20 6V-3382 Lip Type Seal 9 1 Apply blue Loctite 243 to the outside diameter. 118-5805 Special Race Bearing Install the snap ring of the special race bearing toward the shaft flange. 10 1 9S-4185 O- Ring Plug 11 2 Torque to 82 8 N m (60 6 lb ft). 12 6 8T-4187 Bolt Torque to 530 70 N m (391 52 lb ft). 9S-4183 O- Ring Plug 13 2 Torque to 190 20 N m (140 15 lb ft). Illustration 2 g03845364 Section A-A Table 2 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP654... 3/13 Item Qty Part Specification Description 1T-0936 Pipe Plug Install in the orifice toward the head surface or below the head surface. 14 2 Length under test force is 15 mm (0.6 inch). Test force is 15.0 2.0 N (3.4 0.4 lb). Free length after test is 16.15 mm (0.636 inch). 15 1 124-1554 Spring Depth from the head and interface of the port plate is 20.0 0.2 mm (0.79 0.01 inch). D - - 195-4456 Orifice Plug 16 1 Torque to 7 1 N m (62 9 lb in). Illustration 3 g03845365 Section C-C Table 3 Item Qty Part Specification Description Length under test force is 25 mm (1.0 inch). Test force is 60.0 8.0 N (13.5 1.8 lb). Free length after test is 35 mm (1.4 inch). 17 1 230-5483 Spring 18 1 087-4786 Adapter Torque to 115 10 N m (85 7 lb ft). Assembly Procedure Table 4 Required Tools Tool Part Number Part Description Qty A 138-7573 Link Bracket 1 D 3E-3879 Eyebolt 1 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP654... 4/13 F 1U-6396 O-Ring Assembly Compound 1 G - Loctite 242 - H 1P-0510 Driver Gp 1 J 6V-2055 Grease 1 K 128-5049 Guide Stud 2 Illustration 4 g02421056 1. Lubricate actuator piston (41) with the oil that is being used. Install actuator piston (41) into housing (2). Apply Tooling (F) onto O-ring seal of plug (40). Install plug (40) into motor housing (2).Tighten plug (42) to a torque of 430 40 N m (315 30 lb ft). 2. Apply Tooling (G) onto outside diameter of seal (43). Use Tooling (H) to install seal (43). Install retaining ring (42). Illustration 5 g02421000 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP654... 5/13 Illustration 6 g02420998 3. Install pins (39) and keys (38) into motor housing (2). Illustration 7 g02421876 Illustration 8 g02421958 4. Use a suitable press to install bearing (36) and bearing (37) onto shaft assembly (25). Bearing (36) must be installed with Retaining Clip (X) toward the barrel assembly. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP654... 6/13 Illustration 9 g02420596 Illustration 10 g02423556 5. Install barrel spacer (35), Belleville washers (34), thin shim (33), and bearing (32) onto barrel assembly (28). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP654... 7/13 Illustration 11 g02420578 6. Install pistons (30) and plate (31) onto barrel assembly (28). Illustration 12 g02420544 7. Install swashplate (29) and barrel assembly (28) onto shaft assembly (25). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP654... 8/13 Illustration 13 g02423621 8. Use Tooling (D) and a suitable lifting device to install the rotating group into motor housing (2). The weight of the rotating group is approximately 30 kg (65 lb). Note: Align the notches of swashplate (29) with the keys in the motor housing (2). Note: Protect shaft seal (43) from damage by covering the splines on shaft assembly (25) with heat shrink tubing. Illustration 14 g02423738 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP654... 9/13 Illustration 15 g02423742 9. Install plates (26) and friction discs (27). Start with plate (26). Alternate between plates (26) and friction discs (27) with plates (26) on the top and the bottom. Illustration 16 g02419659 10. Install backup ring (21) and O-ring seal (22) onto brake piston (20). 11. Install backup ring (24) and O-ring seal (23) onto brake piston (20). Illustration 17 g02419577 12. Install O-ring seals (19) onto motor housing (2). Install springs (18) onto brake piston (20). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP6... 10/13 Illustration 18 g02419439 13. Install balls (17), backup rings (15), O-ring seals (16), and retainers (14) into head assembly (3). Illustration 19 g02419416 Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. 14. Install spring (13), spool (12), and adapter (11). Tighten adapter (11) to a torque of 115 10 N m (85 7 lb ft). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

Suggest: If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading

352F Excavators YEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP6... 11/13 Illustration 20 g02419359 15. Install ball (9), spring (8), and orifice (7). Tighten orifice (7) to a torque of 7 1 N m (62 9 lb in). 16. Install bearing (6) and O-ring seal (10) onto head assembly (3). Illustration 21 g02001974 Illustration 22 g02419358 17. Apply Tooling (K) to the back side of plate (5) to hold plate (5) in place during assembly. Install plate (5) to head assembly (3). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/10/14

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com