Caterpillar Cat 325D and 325D L Excavator (Prefix SCR) Service Repair Manual Instant Download

Service Repair Manual Models 325D and325DL Excavator

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 1/2 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 325D L EXCAVATOR SCR Configuration: 325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine Disassembly and Assembly C7 Engines for Caterpillar Built Machines Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014 i02303869 Rocker Shaft and Pushrod - Install SMCS - 1102-012; 1208-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 8T-2998 Lubricant 1 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 2/2 Illustration 1 g01153544 1. Apply Tooling (A) to both ends of pushrods (6) . 2. Lubricate pushrods (6) with clean engine oil. Install pushrods (6) and inlet valve bridges (5) . 3. Position rocker shaft (3). Install bolts (1) and bolts (2). Finger tighten bolts (1) and bolts (2). Tighten bolts (2) and bolts (1) to standard torque. 4. Apply Tooling (A) to each of the button faces of the rocker arms. 5. Adjust the valve lash of the rocker arm by turning rocker arm adjustment screws (4). Refer to Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust". End By: Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install". Copyright 1993 - 2020 Caterpillar Inc. Wed Jun 3 15:41:31 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 1/4 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 325D L EXCAVATOR SCR Configuration: 325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine Disassembly and Assembly C7 Engines for Caterpillar Built Machines Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014 i02303932 Cylinder Head - Remove SMCS - 1100-011 Removal Procedure Start By: A. Remove the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve Mechanism Cover Base - Remove and Install". B. Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft And Pushrod - Remove". C. Remove the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Remove". D. Remove the fan drive mounting group. Refer to Disassembly and Assembly, "Fan Drive Mounting Group - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 2/4 Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. Illustration 1 g01153598 1. Disconnect harness assemblies (1), (2), (3), (4), and (5) . Illustration 2 g01153599 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 3/4 2. Disconnect hose assembly (6) and tube assembly (7) . Illustration 3 g01153600 3. Disconnect tube assembly (8) and tube assembly (10) from turbocharger (9) . Illustration 4 g01153645 4. Attach a suitable lifting device to cylinder head (11). The weight of cylinder head (11) is approximately 175 kg (385 lb). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 4/4 5. Remove bolts (12) and bolts (13). Remove cylinder head (11) and the gasket from the cylinder block. Copyright 1993 - 2020 Caterpillar Inc. Wed Jun 3 15:42:26 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 1/5 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 325D L EXCAVATOR SCR Configuration: 325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine Disassembly and Assembly C7 Engines for Caterpillar Built Machines Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014 i02304034 Cylinder Head - Install SMCS - 1100-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 6V-4876 Lubricant 1 B 4C-5590 Anti-Seize Compound 1 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Install a new cylinder head gasket. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 2/5 Illustration 1 g01153645 Illustration 2 g01153662 Note: To avoid damage to the cylinder head gasket, use guide bolts of an appropriate size to install the cylinder head. 2. Attach a suitable lifting device to cylinder head (11). The weight of cylinder head (11) is approximately 175 kg (385 lb). Position cylinder head (11) onto the cylinder block. 3. Apply Tooling (A) to the threads and both sides of the washers of bolts (12). Apply Tooling (B) to the threads and both sides of the washers of bolts (13). Install bolts (12) and bolts (13) . 4. Tighten the cylinder head bolts according to the following procedure: https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 3/5 a. Tighten Bolt (1) through Bolt (14) in a numerical sequence to a torque of 300 15 N m (221 11 lb ft). b. Loosen Bolt (1) through Bolt (14) until the washers are loose under the bolt heads. c. Tighten Bolt (1) through Bolt (14) in a numerical sequence to a torque of 130 15 N m (95 11 lb ft). d. Tighten Bolt (1) through Bolt (14) again in a numerical sequence to a torque of 130 15 N m (95 11 lb ft). e. Turn Bolt (1) through Bolt (14) in a numerical sequence for an additional 90 (1/4 turn). f. Tighten Bolt (15) through Bolt (20) in a numerical sequence to a torque of 55 7 N m (41 5 lb ft). Illustration 3 g01153600 5. Connect tube assembly (8) and tube assembly (10) to turbocharger (9) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 4/5 Illustration 4 g01153599 6. Connect hose assembly (6) and tube assembly (7) . Illustration 5 g01153598 7. Connect harness assemblies (1), (2), (3), (4), and (5) . End By: a. Install the fan drive mounting group. Refer to Disassembly and Assembly, "Fan Drive Mounting Group - Remove and Install". b. Install the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Install". c. Install the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft And Pushrod - Install". https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 5/5 d. Install the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve Mechanism Cover Base - Remove and Install". Copyright 1993 - 2020 Caterpillar Inc. Wed Jun 3 15:43:22 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 1/4 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 325D L EXCAVATOR SCR Configuration: 325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine Disassembly and Assembly C7 Engines for Caterpillar Built Machines Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014 i02304097 Lifter Group - Remove and Install SMCS - 1209-010 Removal Procedure Start By: A. Remove the rocker arms and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove". B. Remove the unit injector hydraulic pump. Refer to Disassembly and Assembly, "Unit Injector Hydraulic Pump - Remove". C. Remove the speed/timing sensors. Refer to Disassembly and Assembly, "Speed/Timing Sensor - Remove and Install". D. Remove the electronic control module (ECM). Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 2/4 Illustration 1 g01125745 1. Remove bolts (1) . 2. Remove side covers (2) . Illustration 2 g01125748 3. Place identification marks on each lifter in order to identify the proper location on the side cover for installation. Note: Ensure that the sleeves of the side covers remain in the side covers. 4. Remove bolts (3) and the dowels that hold lifter arms (4) and lifter shaft (5) to each side cover. Remove seal (6) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 3/4 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 9S-3263 Thread Lock Compound 1 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 3 g01125748 1. Install seal (6) . 2. Install lifter arms (4) on lifter shaft (5) . 3. Position lifter shaft (5) over the dowels on the side cover. Ensure that the oil holes in the lifter shaft are facing the side cover. Apply Tooling (A) on the threads of bolts (3) that hold lifter shaft (5) to the side cover. Install bolts (3). Tighten bolts (3) to a torque of 13 3 N m (10 2 lb ft). Tighten the two center bolts. Then tighten the end bolts. 4. Lubricate the lifters with clean engine oil. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 4/4 Illustration 4 g01125745 5. Position the gaskets and side covers (2). Install bolts (1) . End By: a. Install the electronic control module (ECM). Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install". b. Install the speed/timing sensors. Refer to Disassembly and Assembly, "Speed/Timing Sensor - Remove and Install". c. Install the unit injector hydraulic pump. Refer to Disassembly and Assembly, "Unit Injector Hydraulic Pump - Install". d. Install the rocker arms and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install". Copyright 1993 - 2020 Caterpillar Inc. Wed Jun 3 15:44:18 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 1/2 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 325D L EXCAVATOR SCR Configuration: 325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine Disassembly and Assembly C7 Engines for Caterpillar Built Machines Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014 i02304162 Camshaft - Remove SMCS - 1210-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty 136-4632 Timing Pin 1 A 139-7063 Timing Pin Adapter 1 B FT-2730 Puller 12 Start By: A. Remove the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration Damper and Pulley - Remove and Install". B. Remove the rocker arms and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove". C. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 2/2 1. Use Tooling (B) to reposition the valve lifters out of the way. 2. Ensure that the No. 1 cylinder is at the top center compression stroke. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston". Install Tooling (A) in the flywheel. 3. Ensure that the timing marks on the following gears are aligned: the camshaft drive gear, the idler gear and the crankshaft gear. Illustration 1 g01125899 4. Rotate camshaft gear (1) in order to access bolts (2). Remove bolts (2) . 5. Remove thrust plate (3) . 6. Remove camshaft (4) from the cylinder block. Copyright 1993 - 2020 Caterpillar Inc. Wed Jun 3 15:45:13 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 1/2 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 325D L EXCAVATOR SCR Configuration: 325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine Disassembly and Assembly C7 Engines for Caterpillar Built Machines Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014 i02304177 Camshaft - Install SMCS - 1210-012 Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 2/2 Illustration 1 g01125899 1. Carefully install camshaft (4) in the cylinder block. 2. Install thrust plate (3) . 3. If necessary, rotate camshaft gear (1) in order to access thrust plate (3). Install bolts (2) . 4. Ensure that the No. 1 cylinder is at the top center compression stroke. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston". 5. Ensure that the timing marks on the following gears are aligned: the camshaft drive gear, the idler gear and the crankshaft gear. End By: a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and Install". b. Install the rocker arms and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install". c. Install the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration Damper and Pulley - Remove and Install". Copyright 1993 - 2020 Caterpillar Inc. Wed Jun 3 15:46:09 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 1/2 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 325D L EXCAVATOR SCR Configuration: 325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine Disassembly and Assembly C7 Engines for Caterpillar Built Machines Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014 i06290358 Camshaft Gear - Remove and Install SMCS - 1210-010-GE Removal Procedure Start By: A. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove". 1. Wrap the camshaft with a protective covering in order to prevent damage to the camshaft. Illustration 1 g00987675 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 2/2 NOTICE Do not allow the camshaft to fall to the floor when pressing it from the drive gear. Also make sure that the camshaft lobes do not catch on the press plates. 2. Place the camshaft assembly in a suitable press. Press camshaft (2) from camshaft gear (1) . 3. If necessary, remove key (3) from the camshaft. Installation Procedure 1. Raise the temperature of the camshaft gear from 200 C (392 F) to 250 C (482 F). Note: Do not use a torch to heat the camshaft gear. Illustration 2 g00987675 2. Align key (3) in the camshaft with the groove (keyway) in the camshaft gear. 3. Install camshaft gear (1) on the end of camshaft (2) . End By: Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install". Copyright 1993 - 2020 Caterpillar Inc. Wed Jun 3 15:47:05 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 1/4 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 325D L EXCAVATOR SCR Configuration: 325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine Disassembly and Assembly C7 Engines for Caterpillar Built Machines Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014 i02232381 Camshaft Bearings - Remove and Install SMCS - 1211-010 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 8S-2241 Camshaft Bearing Tool Group 1 Start By: a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Note: Note the oil hole orientation in each camshaft bearing prior to removal for assembly purposes. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 2/4 Illustration 1 g00989974 1. Use Tooling (A) to remove camshaft bearing (1) from the front of the cylinder block. Remove the remaining camshaft bearings (2) from the cylinder block. Installation Procedure Table 2 Required Tools Tool Part Number Part Description Qty A 8S-2241 Camshaft Bearing Tool Group 1 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 3/4 Illustration 2 g00990062 1. Use Tooling (A) to install all of the camshaft bearings (2) except for the front camshaft bearing. Locate the oil hole in each bearing so that oil hole (3) is located at the top of the bore. Refer to Specifications for more information. Illustration 3 g00989938 2. Use Tooling (A) to install front camshaft bearing (1). Align oil hole (5) in the front camshaft bearing with the oil hole in the cylinder block. Locate joint (4) in the front camshaft bearing in the proper position. Refer to Specifications for more information. End By: a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install". https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

Suggest: If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 1/3 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 325D L EXCAVATOR SCR Configuration: 325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine Disassembly and Assembly C7 Engines for Caterpillar Built Machines Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014 i05954439 Engine Oil Pan - Remove and Install SMCS - 1302-010 Removal Procedure Start By: A. Remove the engine. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

325D & 325D L Excavators SCR00001-UP (MACHINE) POWERED BY C7 Engine(... 2/3 1. Drain the engine oil into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct draining and filling procedures. Illustration 1 g01153839 Note: Do not pry or gouge the sealing surface of the engine oil pan. Use a rubber mallet to tap lightly on the engine oil pan, if necessary. 2. Remove bolts (2) . Remove engine oil pan (1) and the gasket. Installation Procedure Table 1 Tool Part number Part Description Qty A - Loctite 598 1 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/6/3

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com