Caterpillar Cat 160H Motor Grader (Prefix ASD) Service Repair Manual Instant Download
Please open the website below to get the complete manualnn//
Download Presentation
Please find below an Image/Link to download the presentation.
The content on the website is provided AS IS for your information and personal use only. It may not be sold, licensed, or shared on other websites without obtaining consent from the author. Download presentation by click this link. If you encounter any issues during the download, it is possible that the publisher has removed the file from their server.
E N D
Presentation Transcript
Service Repair Manual Models 160H M otor Grader
160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine(SEB... 1/9 Shutdown SIS Previous Screen Product: MOTOR GRADER Model: 160H MOTOR GRADER ASD Configuration: 160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine Disassembly and Assembly 12H, 140H and 160H Motor Graders Machine Systems Media Number -RENR4124-06 Publication Date -01/09/2007 Date Updated -24/09/2007 i05508896 Circle Drive - Disassemble SMCS - 5207-015 Disassembly Procedure Table 1 Required Tools Tool Part Number Part Description Qty A Forcing Bolt 3/8-16 by 4 inch 2 B 138-7575 Link Bracket 1 C 8H-0663 Bearing Puller Gp 1 8B-7554 Bearing Cup Puller Gp 1 D 8B-7548 Push-Puller Tool Gp 1 Start By: a. Remove the circle drive. Refer to Disassembly and Assembly, "Circle Drive - Remove". Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly procedures on a clean work surface. Keep components covered and protected at all times. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/28
160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine(SEB... 2/9 Illustration 1 g00937730 1. Remove coupling (1) from housing (3). Remove pin (2) from coupling (1). Illustration 2 g00937733 2. Remove nuts (4). Remove bracket (5). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/28
https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com
160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine(SEB... 3/9 3. Remove O-ring seal (7) and shims (8). 4. Remove bearing cup (6) from bracket (5). Illustration 3 g00937735 5. Remove bolts (9) and cover (10). 6. Remove bolts (11). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/28
160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine(SEB... 4/9 Illustration 4 g00937707 7. Install Tooling (A) and remove cover (12). Illustration 5 g00937728 8. Remove plug (13) and O-ring seal (14) from cover (12). 9. Remove bearing (15) from cover (12). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/28
160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine(SEB... 5/9 Illustration 6 g00937708 10. Install Tooling (B) on shaft assembly (16). Attach a suitable lifting device to Tooling (B). The weight of shaft assembly (16) is approximately 32 kg (70 lb). 11. Remove shaft assembly (16). Remove Tooling (B). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/28
160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine(SEB... 6/9 Illustration 7 g00937732 12. Remove remaining bolts (17) and retainer (18). Remove spacer (19) and shims (20). 13. Remove spring (21) and spacer (22). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/28
160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine(SEB... 7/9 Illustration 8 g00937709 14. Remove gear (23) from shaft assembly (16). Remove friction discs (24) and discs (25) from gear (23). Remove spacer (26). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/28
160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine(SEB... 8/9 Illustration 9 g00937727 15. Remove thrust washer (27) and remove bearing (28). 16. Remove worm assembly (29) from housing (3). Illustration 10 g00937739 17. Use Tooling (C) and a suitable press in order to remove bearings (31) from worm assembly (29). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/28
160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine(SEB... 9/9 Illustration 11 g00937737 18. Use Tooling (D) in order to remove bearing cup (32) from housing (3). Copyright 1993 - 2019 Caterpillar Inc. Thu Nov 28 11:22:20 UTC+0800 2019 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/28
160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine(SEB... 1/12 Shutdown SIS Previous Screen Product: MOTOR GRADER Model: 160H MOTOR GRADER ASD Configuration: 160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine Disassembly and Assembly 12H, 140H and 160H Motor Graders Machine Systems Media Number -RENR4124-06 Publication Date -01/09/2007 Date Updated -24/09/2007 i07424503 Circle Drive - Assemble SMCS - 5207-016 Assembly Procedure Table 1 Required Tools Tool Part Number Part Description Qty B 439-3940 Bracket As 1 E 8T-5096 Dial Indicator Gp 1 F - Loctite 243 - Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/28
160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine(SEB... 2/12 Illustration 1 g02815057 1. Lower the temperature of bearing cup (32). Install bearing cup (32) in housing (3). Lower the temperature of bearing (28). Install bearing (28) to a depth of 2.00 0.50 mm (0.079 0.020 inch) below the face. Illustration 2 g00938141 2. Raise the temperature of bearing cones (31). Install bearing cones (31) on worm assembly (29). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/28
160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine(SEB... 3/12 Illustration 3 g03890578 Illustration 4 g03890590 3. Install worm assembly (29) in housing (3). 4. Lower the temperature on bearing cup (6). Install bearing cup (6) in bracket (5). 5. Torque nut (4A) to 20 N m (15 lb ft) and nut (4B) 40 N m (30 lb ft). Then Torque nut (4A) to 80 N m (60 lb ft) and nut (4B) 80 N m (60 lb ft). Rotate the worm 3 revolutions then back off the nuts. 6. Torque nut (4A) to 20 N m (15 lb ft) and nut (4B) 40 N m (30 lb ft) then torque nut (4A) to 40 N m (30 lb ft) rotate the worm 3 revolutions. 7. Torque nut (4A) to 40 N m (30 lb ft) and nut (4B) 40 N m (30 lb ft). Measure the average gap between the housing and adapter at the locations being torqued. Subtract 0.145 0.065 mm (0.006 0.003 inch) to obtain the desire shim pack thickness. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/28
160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine(SEB... 4/12 Illustration 5 g00938174 8. Remove nuts (4) and bracket (5). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/28
160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine(SEB... 5/12 Illustration 6 g00938187 9. Install gear (23) on shaft assembly (16). Install spacer (26). Install friction discs (24) and discs (25) in gear (23). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/28
160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine(SEB... 6/12 Illustration 7 g00938190 10. Install spacer (22), spring (21), and spacer (19). 11. Install Tooling (B) (not shown) and bolts (17). Attach a suitable lifting device to Tooling (B). The weight of shaft assembly (16) is approximately 32 kg (70 lb). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/28
160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine(SEB... 7/12 Illustration 8 g00938199 12. Install thrust washer (27). Illustration 9 g02816216 Note: If bolts (17) are M16 bolts, follow Step 13 through Step 19 for the correct shimming procedure. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/28
160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine(SEB... 8/12 13. Install shaft assembly (16). Remove Tooling (B). Tighten bolts (17) to 150 20N m (111 15 lb ft). 14. Wait 45 minutes, then remove bolts (17) and retainer (18) to add shims (20) 15. Determine the required number of shims (20) to obtain 2.30 0.25 mm (0.10 0.01 inch) of deflection in spring (21). Use a depth micrometer to obtain the distance from the end of shaft assembly (16) to the flat surface on spacer (19). 16. Subtract 2.30 0.25 mm (0.10 0.01 inch) from the dimension that was measured in Step 15. The calculated dimension is the thickness of shims (20). 17. Install shims (20), retainer (18), and bolts (17). 18. Tighten bolts (17) to a torque of 240 40 N m (177 30 lb ft). 19. Tighten bolts (17) again to a torque of 240 40 N m (177 30 lb ft). Note: If bolts (17) are 1/2-13 thd bolts, follow Step 20 through Step 26 for the correct shimming procedure. 20. Install shaft assembly (16). Remove Tooling (B). Tighten bolts (17) to 130 7 N m (96 5 lb ft). 21. Wait 45 minutes, then remove bolts (17) and retainer (18) to add shims (20) 22. Determine the required number of shims (20) to obtain 2.30 0.25 mm (0.10 0.01 inch) of deflection in spring (21). Use a depth micrometer to obtain the distance from the end of shaft assembly (16) to the flat surface on spacer (19). 23. Subtract 2.30 0.25 mm (0.10 0.01 inch) from the dimension that was measured in Step 15. The calculated dimension is the thickness of shims (20). 24. Install shims (20), retainer (18), and bolts (17). 25. Tighten bolts (17) to a torque of 130 7 N m (96 5 lb ft). 26. Tighten bolts (17) again to a torque of 130 7 N m (96 5 lb ft). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/28
160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine(SEB... 9/12 Illustration 10 g00938238 27. Lower the temperature of bearing (15). Install bearing (15) even with the bottom face of cover (12). 28. Install O-ring seal (14) on cover (12). Lubricate the O-ring seal with the lubricant that is being sealed. Install plug (13). 29. Install cover (12). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/28
Suggest: If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading
160H Motor Grader ASD00001-UP (MACHINE) POWERED BY 3176C Engine(S... 10/12 Illustration 11 g03802219 30. Install five bolts (11). Apply Tooling (F) to new bolts (11A). Install new bolts (11A), as shown. 31. Install cover (10) and bolts (9). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/28
https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com
