Case IH MXM120 MXM130 MXM140 Tractors Supplement to Operator Manual (6-32931) Operator’s Manual Instant Download

MXM120 MXM130 MXM140 TRACTORS SUPPLEMENT TO OPERATORS MANUAL PRINT No. 6- -32931 (82998836)

Series MXM Operators Manual Supplement INTRODUCTION If at any time you require advice concerning your tractor, do not hesitate to contact your authorised Case IH dealer. He has factory trained personnel, genuine parts and the necessary equipment to carry out all your service requirements. This Supplement details new features that are available to enhance the specification of tractors in the Case MXM range. The Supplement should be read in conjunction with the Operators Manual supplied with the tractor. Read the Supplement carefully and keep it, together with the Operators Manual, in a convenient place for future reference. ThesectionswithinthisSupplementarenumberedto match those of the OperatorsManual. However,only those sections where changes have occured will appear in the Supplement. SECTION 2 Subject Page Cab and Platform Controls Hand Throttle 2--2 2--4 Clutch/Inching Pedal 2--4 Analogue Instrument Panel 2--5 Indicator and Warning Lights Transmission Display -- Two--Speed Powershift 2--5 2--6 Groundspeed Calibration 2--7 Malfunction Warning Symbols 2--8 20 x 16 Synchro Shift Transmission 2--9 24 x 12 Two--Speed Powershift Transmission Electronic Management Unit 2--14 2--22 Front and Rear Differential Lock 2--22 Four Wheel Drive 2--25 SECTION 3 Subject Starting the Engine Page 3--2 Stopping the Engine 3--3 Mechanical Lower Link Sensing Hydraulics 3--4 Remote Control Valves, Open Centre Type Lift Rods, Lower Links and Top Link 3--10 3--17

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com

SECTION 4 Subject Page Lubrication and Maintenance Chart 4--2 Recommended Fluids 4--2 When the Warning Lamp Lights Check Brake Fluid 4--3 Every 300 Hours Check Transmission and Hydraulic Oil Level 4--3 Every 600 Hours Change Transmission and Hydraulic Filters 4--4 Every 1200 Hours Change Transmission, Hydraulic Oil and Filters General Maintenance When Required Two--Speed Powershift Transmission Clutch Calibration 4--5 4--6 SECTION 5 Subject Page Transmissions 20 x 16 Synchro Shift 24 x 12 Two--Speed Powershift 5--2 5--3 SECTION 8 Subject Page Transmission options 20 x 16 Synchro Shift 24 x 12 Two--Speed Powershift 8--1 8--1 Hydraulic System Open Centre System with Mechanical Lower Link Sensing 8--1 3--Speed Ground Drive P.T.O. 8--1 Fluid Capacities, Transmission/Rear Axle and Hydraulic System 8--2 SECTION 9 Subject Clutch master cylinder fluid level check Page 9--1, 9--3

SECTION 2 CONTROLS, INSTRUMENTS AND OPERATION BEFORE OPERATING Subject Page CAUTION Cab and Platform Controls 2--2 Before driving or operating the tractor, study the safety precautions in Section 1 of the Operators Manual. Hand Throttle 2--4 Clutch/Inching Pedal 2--4 Analogue Instrument Panel 2--5 This supplement updates the information contained inyourtractorOperatorsManualandshouldbeused in conjunction with that publication. Indicator and Warning Lights 2--5 Transmission Display -- Two--Speed Powershift 2--6 It may help if you identify the relevant sections and pages in the Operators Manual where the new information applies so you canbe sureto consultthe supplement wherever necessary. Groundspeed Calibration 2--7 Malfunction Warning Symbols 2--8 20 x 16 Synchro Shift Transmission 2--9 As far as possible, the order in which the subjects appear in the supplement will follow that of the Operators Manual. 24 x 12 Two--Speed Powershift Transmission 2--14 Electronic Management Unit 2--22 Do not start the engine or attempt to drive or operate the tractor until you are fully accustomed with all the controls. It is too late to learn once the tractor is moving. If in doubt about any aspect of operation of the tractor, consult your authorised dealer. Front and Rear Differential Lock 2--22 Four Wheel Drive 2--25 2--1

SECTION 2 - - CONTROLS, INSTRUMENTS AND OPERATION CAB AND PLATFORM CONTROLS 1 General View of Tractor Controls - - MXM120, MXM130 and MXM140 2--2

SECTION 2 - - CONTROLS, INSTRUMENTS AND OPERATION Key to Figure 1 Page Nos. for Reference 1. 2. Creep speed selector Clutch/inching pedal Synchro Shift transmission Two--Speed powershift transmission Shuttle lever Synchro Shift transmission Two--Speed powershift transmission Instrument panel Analogue and analogue/digital instrument panel Hand throttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transmission controls Synchro Shift transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Two--Speed powershift transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulics controls Mechanical lower link sensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote control valve levers Open centre type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External hydraulic power lift control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2--11, 2--17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2--9 2--14 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2--10 2--14 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2--5 2--4 5. 6. 2--9 2--14 7. 3--4 8. 3--10 3--9 9. 2--3

SECTION 2 - - CONTROLS, INSTRUMENTS AND OPERATION Hand Throttle Thethrottlelever(1)controlsenginespeed.Pushthe lever forward to progressively increase engine speed. Pull rearward to reduce engine speed. 1 2 Clutch/Inching Pedal When the clutch pedal (1) is depressed the drive between the engine and transmission will be disengaged. Synchro Shift Transmission Use the pedal to transfer engine power smoothly to the driving wheels when moving off or when changing gear. See TRANSMISSION later in this section for further details. 3 Two- -Speed Powershift Transmission Use the pedal to control tractor movement in confined areas orwhen couplingto implements.See TRANSMISSION later in this section for further details. NOTE:Ifthetractorremainsstationaryformorethan 30 seconds with the controls in neutral and the engine running, the clutch pedal must be cycled before drive can be re- -engaged. NOTE: To avoid premature wear, do not use the clutch/Inching pedal as a footrest. 2--4

Suggest: If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading

SECTION 2 - - CONTROLS, INSTRUMENTS AND OPERATION ANALOGUE AND ANALOGUE / DIGITAL INSTRUMENT PANELS Two types of analogue instrument panel are available, dependent upon model and specification level.Figure 4showstheanalogueinstrumentpanel. The upper section of the instrument panels consists of 21 coloured lights (1) which provide operating information or give warning of system malfunction. Both instrumentpanels havethree analoguegauges (2), (3) and (4). 4 The instruments are illuminated when the tractor lights are turned on. The instrument panel is also equipped with an audio alarm function. 5 Indicator and Warning Lights The twenty one coloured lights provide operating information or give warning of system malfunction. The lights are common to both instrument panels and their illumination may be accompanied by a critical or non critical alarm sound. 9. Transmission oil pressure low: Steady light indicates that the transmission lubrication circuit oil pressure is low. Stop the engine and investigate the cause. 2--5

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com