CASE IH Magnum 310 Rowtrac™ PST TIER 4B Tractor Service Repair Manual [ZGRF05001 - ]

SERVICE MANUAL Magnum 250 PST TIER 4B [ZGRF05001 - ], Magnum 280 PST TIER 4B [ZGRF05001 - ], Magnum 310 PST TIER 4B [ZGRF05001 - ], Magnum 310 Rowtrac PST TIER 4B [ZGRF05001 - ], Magnum 340 PST TIER 4B [ZGRF05001 - ], Magnum 340 Rowtrac PST TIER 4B [ZGRF05001 - ] 48115454 13/04/2017 EN

Link Product / Engine Product Market Product Australia New Zealand Engine Magnum 250 PST TIER 4B [ZGRF05001 - ] Magnum 250 PST TIER 4B [ZGRF05001 - ] Magnum 280 PST TIER 4B [ZGRF05001 - ] Magnum 280 PST TIER 4B [ZGRF05001 - ] Magnum 310 PST TIER 4B [ZGRF05001 - ] Magnum 310 PST TIER 4B [ZGRF05001 - ] Magnum 340 PST TIER 4B [ZGRF05001 - ] Magnum 340 PST TIER 4B [ZGRF05001 - ] Magnum 310 Rowtrac PST TIER 4B [ZGRF05001 - ] Magnum 310 Rowtrac PST TIER 4B [ZGRF05001 - ] Magnum 340 Rowtrac PST TIER 4B [ZGRF05001 - ] Magnum 340 Rowtrac PST TIER 4B [ZGRF05001 - ] F2CFE613G*B002 North America F2CFE613G*B002 Australia New Zealand F2CFE614G*B002 North America F2CFE614G*B002 Australia New Zealand F2CFE614D*B002 North America F2CFE614D*B002 North America F2CFE614C*B002 Australia New Zealand F2CFE614C*B002 Australia New Zealand F2CFE614D*B002 North America F2CFE614D*B002 Australia New Zealand F2CFE614C*B002 North America F2CFE614C*B002 48115454 13/04/2017

Contents INTRODUCTION Engine....................................................................................... 10 [10.001] Engine and crankcase ............................................................. 10.1 [10.101] Cylinder heads ..................................................................... 10.2 [10.202] Air cleaners and lines .............................................................. 10.3 [10.206] Fuel filters .......................................................................... 10.4 [10.216] Fuel tanks .......................................................................... 10.5 [10.218] Fuel injection system............................................................... 10.6 [10.304] Engine lubrication system.......................................................... 10.7 [10.310] Aftercooler.......................................................................... 10.8 [10.400] Engine cooling system ............................................................. 10.9 [10.414] Fan and drive .................................................................... 10.10 [10.500] Selective Catalytic Reduction (SCR) exhaust treatment......................... 10.11 Power coupling........................................................................... 19 [19.100] Drive shaft.......................................................................... 19.1 [19.110] Flywheel damper ................................................................... 19.2 [19.120] Drive shaft shield assembly........................................................ 19.3 Transmission.............................................................................. 21 [21.105] Powershift transmission hydraulic components.................................... 21.1 [21.113] Powershift transmission ............................................................ 21.2 [21.135] Powershift transmission external controls.......................................... 21.3 [21.155] Powershift transmission internal components...................................... 21.4 [21.200] Dropbox ............................................................................ 21.5 [21.900] Hydraulic pump drive............................................................... 21.6 Four-Wheel Drive (4WD) system .................................................. 23 [23.202] Electro-hydraulic control ........................................................... 23.1 48115454 13/04/2017

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com

[23.314] Drive shaft.......................................................................... 23.2 Front axle system ....................................................................... 25 [25.100] Powered front axle ................................................................. 25.1 [25.102] Front bevel gear set and differential ............................................... 25.2 [25.108] Final drive hub, steering knuckles, and shafts ..................................... 25.3 [25.122] Axle suspension control............................................................ 25.4 Rear axle system........................................................................ 27 [27.100] Powered rear axle.................................................................. 27.1 [27.106] Rear bevel gear set and differential................................................ 27.2 [27.120] Planetary and final drives .......................................................... 27.3 [27.610] Rear axle track yoke assembly .................................................... 27.4 Power Take-Off (PTO)................................................................. 31 [31.104] Rear electro-hydraulic control...................................................... 31.1 [31.110] One-speed rear Power Take-Off (PTO) ............................................ 31.2 [31.114] Two-speed rear Power Take-Off (PTO) ............................................ 31.3 [31.146] Front Power Take-Off (PTO) ....................................................... 31.4 Brakes and controls .................................................................... 33 [33.110] Parking brake or parking lock ...................................................... 33.1 [33.202] Hydraulic service brakes ........................................................... 33.2 [33.220] Trailer brake hydraulic control...................................................... 33.3 [33.224] Trailer brake pneumatic control .................................................... 33.4 Hydraulic systems....................................................................... 35 [35.000] Hydraulic systems.................................................................. 35.1 [35.102] Pump control valves................................................................ 35.2 [35.106] Variable displacement pump ....................................................... 35.3 [35.114] Three-point hitch control valve ..................................................... 35.4 [35.124] Three-point hitch hydraulic adjustment ............................................ 35.5 [35.204] Remote control valves ............................................................. 35.6 48115454 13/04/2017

[35.300] Reservoir, cooler, and filters........................................................ 35.7 [35.304] Combination pump units ........................................................... 35.8 Hitches, drawbars, and implement couplings.................................. 37 [37.110] Rear three-point hitch .............................................................. 37.1 [37.162] Front hitch.......................................................................... 37.2 Frames and ballasting................................................................. 39 [39.100] Frame .............................................................................. 39.1 Steering..................................................................................... 41 [41.101] Steering control .................................................................... 41.1 [41.200] Hydraulic control components...................................................... 41.2 [41.206] Pump............................................................................... 41.3 [41.432] Autoguidance steering ............................................................. 41.4 Wheels...................................................................................... 44 [44.520] Rear wheels........................................................................ 44.1 Tracks and track suspension........................................................ 48 [48.100] Tracks .............................................................................. 48.1 [48.130] Track frame and driving wheels.................................................... 48.2 [48.134] Track tension units ................................................................. 48.3 [48.138] Track rollers ........................................................................ 48.4 Cab climate control..................................................................... 50 [50.100] Heating............................................................................. 50.1 [50.200] Air conditioning..................................................................... 50.2 [50.300] Cab pressurizing system........................................................... 50.3 Electrical systems....................................................................... 55 [55.000] Electrical system ................................................................... 55.1 [55.010] Fuel injection system............................................................... 55.2 [55.012] Engine cooling system ............................................................. 55.3 48115454 13/04/2017

[55.013] Engine oil system .................................................................. 55.4 [55.014] Engine intake and exhaust system................................................. 55.5 [55.015] Engine control system.............................................................. 55.6 [55.024] Transmission control system....................................................... 55.7 [55.045] Front axle control system .......................................................... 55.8 [55.046] Rear axle control system........................................................... 55.9 [55.047] Steering control system .......................................................... 55.10 [55.050] Heating, Ventilation, and Air-Conditioning (HVAC) control system............... 55.11 [55.051] Cab Heating, Ventilation, and Air-Conditioning (HVAC) controls................. 55.12 [55.100] Harnesses and connectors....................................................... 55.13 [55.130] Rear three-point hitch electronic control system ................................. 55.14 [55.201] Engine starting system........................................................... 55.15 [55.301] Alternator......................................................................... 55.16 [55.302] Battery............................................................................ 55.17 [55.408] Warning indicators, alarms, and instruments .................................... 55.18 [55.510] Cab or platform harnesses and connectors...................................... 55.19 [55.512] Cab controls...................................................................... 55.20 [55.513] Cab transmission controls........................................................ 55.21 [55.518] Wiper and washer system........................................................ 55.22 [55.640] Electronic modules............................................................... 55.23 [55.988] Selective Catalytic Reduction (SCR) electrical system .......................... 55.24 [55.DTC] FAULT CODES.................................................................. 55.25 Platform, cab, bodywork, and decals............................................. 90 [90.100] Engine hood and panels ........................................................... 90.1 [90.102] Engine shields, hood latches, and trims ........................................... 90.2 [90.124] Pneumatically-adjusted operator seat.............................................. 90.3 [90.150] Cab................................................................................. 90.4 [90.151] Cab interior......................................................................... 90.5 48115454 13/04/2017

INTRODUCTION 48115454 13/04/2017 1

INTRODUCTION Foreword - Important notice regarding equipment servicing All repair and maintenance work listed in this manual must be carried out only by qualified dealership personnel, strictly complying with the instructions given, and using, whenever possible, the special tools. Anyone who performs repair and maintenance operations without complying with the procedures provided herein shall be responsible for any subsequent damages. The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional, or local dealers, reject any responsibility for damages caused by parts and/or components not approved by the manu- facturer, including those used for the servicing or repair of the product manufactured or marketed by the manufacturer. In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case of damages caused by parts and/or components not approved by the manufacturer. The manufacturer reserves the right to make improvements in design and changes in specifications at any time without notice and without incurring any obligation to install them on units previously sold. Specifications, descriptions, and illustrative material herein are as accurate as known at time of publication but are subject to change without notice. In case of questions, refer to your CASE IH Sales and Service Networks. 48115454 13/04/2017 3

INTRODUCTION Safety rules Personal safety This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible death or injury. Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in- structions. These precautions are intended for the personal safety of you and those working with you. Read and understand all the safety messages in this manual before you operate or service the machine. DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury. WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury. CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury. FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT IN DEATH OR SERIOUS INJURY. Machine safety NOTICE: Notice indicates a situation that, if not avoided, could result in machine or property damage. Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or property damage. The word Notice is used to address practices not related to personal safety. Information NOTE: Note indicates additional information that clarifies steps, procedures, or other information in this manual. Throughout this manual you will find the word Note followed by additional information about a step, procedure, or other information in the manual. The word Note is not intended to address personal safety or property damage. 48115454 13/04/2017 4

INTRODUCTION Safety rules - General maintenance safety General maintenance safety Keep the area used for servicing the machine clean and dry. Clean up spilled fluids. Service the machine on a firm, level surface. Install guards and shields after you service the machine. Close all access doors and install all panels after servicing the machine. Do not attempt to clean, lubricate, clear obstructions, or make adjustments to the machine while it is in motion or while the engine is running. Always make sure that working area is clear of tools, parts, other persons and pets before you start operating the machine. Unsupported hydraulic cylinders can lose pressure and drop the equipment, causing a crushing hazard. Do not leave equipment in a raised position while parked or during service, unless the equipment is securely supported. Jack or lift the machine only at jack or lift points indicated in this manual. Incorrect towing procedures can cause accidents. When you tow a disabled machine follow the procedure in this manual. Use only rigid tow bars. Stop the engine, remove the key, and relieve pressure before you connect or disconnect fluid lines. Stop the engine and remove the key before you connect or disconnect electrical connections. Scalding can result from incorrect removal of coolant caps. Cooling systems operate under pressure. Hot coolant can spray out if you remove a cap while the system is hot. Allow the system to cool before you remove the cap. When you remove the cap, turn it slowly to allow pressure to escape before you completely remove the cap. Replace damaged or worn tubes, hoses, electrical wiring, etc. The engine, transmission, exhaust components, and hydraulic lines may become hot during operation. Take care when you service such components. Allow surfaces to cool before you handle or disconnect hot components. Wear protective equipment when appropriate. When welding, follow the instructions in the manual. Always disconnect the battery before you weld on the machine. Always wash your hands after you handle battery components. 48115454 13/04/2017 5

INTRODUCTION Product identification - Machine orientation 1 RAIL14TR02053GA The right hand and left hand side of the tractor used in this manual are the same as your right hand and left hand when sitting in the tractor seat looking forward. 48115454 13/04/2017 33

SERVICE MANUAL Engine Magnum 250 PST TIER 4B [ZGRF05001 - ], Magnum 280 PST TIER 4B [ZGRF05001 - ], Magnum 310 PST TIER 4B [ZGRF05001 - ], Magnum 310 Rowtrac PST TIER 4B [ZGRF05001 - ], Magnum 340 PST TIER 4B [ZGRF05001 - ], Magnum 340 Rowtrac PST TIER 4B [ZGRF05001 - ] 48115454 13/04/2017 10

Engine - Engine and crankcase Engine - General information - Dynamometer testing guidelines One of the main services which a dealership provides is verifying tractor engine and Power Take-Off (PTO) perfor- mance with a dynamometer. As agricultural engine technology has become more sophisticated, dynamometer testing of these machines must become more sophisticated and consistent to deal with the advancements. During manufacturing, the engine for each machine is run on an engine dynamometer to ensure that the power produced from the engine is within the specified parameters. These tests are performed under strictly controlled con- ditions which can be difficult to replicate in a dealership environment. For example, the following conditions in detail are recorded when establishing the power output of an engine: Humidity Ambient air temperature Atmospheric pressure (barometer) Altitude Fuel temperature Fuel specification Fuel density Dynamometer accuracy Any or all of these factors can affect the power output of an engine, so some tolerances must be applied to power measurements from dynamometer testing at the dealership. Weather, air and fuel conditions affect tractor perfor- mance. As a general rule, remember: As air temperature DECREASES, e power INCREASES. As atmospheric pressure (barometer) DECREASES, power DECREASES. As altitude INCREASES, the power DECREASES about 2% for every 300 m (1500 ft) above 1500 m (5000 ft) for turbo-charged engines. As fuel density INCREASES, power INCREASES. As fuel temperature INCREASES, power DECREASES. A standard test procedure must be followed so that results from a dynamometer test are consistent and accurate. These results can then be recorded and used for future comparison. NOTE: The power/torque readings from a dynamometer test are the rate speed, full load, PTO power maximum torque achieved by the tested tractor. These readings could be lower than the PTO power advertised for the tractor under test, depending on tractor/engine equipment (parasitics) and the ambient environment test conditions. Also note, maximum PTO power may be observed at an engine RPM less than the advertised rated engine RPM. For example, while the rated engine RPM may be 2000 RPM, maximum PTO horsepower may be observed at 1800 RPM. This is typically defined as peak power or power bulge. Perform these actions if a dyno test shows low power 1. Check the fuel injection system for faults or a derate condition. Perform the corresponding fault code resolution and rectify the problem. 2. Run the test a second time to collect comparative data. You must record the ambient air temperature, fuel tem- perature, and water temperature. 3. Check all supply lines for restrictions, air ingress and cleanliness. 4. Check the air intake system and the filter(s) condition and cleanliness. 5. Run the test for a third time. If the power is still not acceptable, escalate the concern with ASIST. Supply the following information: The completed dynamometer testing worksheet. See Engine - General information - Dyno test worksheet (10.001) All other collected documentation such as dynamometer test results, dynamometer calibration, fault codes, service actions taken, etc. 48115454 13/04/2017 10.1 [10.001] / 42

Engine - Engine and crankcase Engine - Remove Prior operation: Battery - Disconnect (55.302) Prior operation: Hood - Remove (90.100) Prior operation: Side shield - Remove (90.102) Prior operation: Air conditioning - Recover (50.200) Prior operation: Engine cooling system - Emptying (10.400) Prior operation: Engine cooling system - Remove (10.400) Prior operation: Diesel Oxidation Catalyst (DOC) - Remove (10.500) NOTE: Clean all fittings before disconnecting. NOTE: Cap or plug all lines and ports when disconnecting hydraulic components. 1. Disconnect the humidity sensor (1) and the air restric- tion sensor (2). Disengage the hose clamp (3) and dis- connect the hose from the air intake tube. 1 RAIL13TR04202AA 2. Disconnect the clamps (1) from each end of the air intake tube and remove the tube. 2 RAIL13TR04211AA 48115454 13/04/2017 10.1 [10.001] / 46

Engine - Engine and crankcase 3. Cut the wire tie (1) securing the harness to the hood support (2). 3 RAIL13TR04204AA 4. Disconnect the starter cables (1) and the auxiliary wire (2). 4 RAIL13TR04209AA 5. Remove the three bolts (1) securing the hood support to the frame. 5 RAIL13TR04209AA 6. Remove the hood support. 6 RAIL13TR04212AA 48115454 13/04/2017 10.1 [10.001] / 47

Engine - Engine and crankcase 7. Disconnect the high pressure A/C hose (1) and the coolant lines (2). Cap or plug all fittings and lines. 7 RAIL13TR04230AA 8. Remove the two bolts (1) from the rear engine mount plate. 8 RAIL13TR04243AA 9. Remove the engine mount cover plate. 9 RAIL13TR04244AA 10. Disconnect the front suspended axle electrical con- nectors (1) if equipped. 10 RAIL13TR04237AA 48115454 13/04/2017 10.1 [10.001] / 48

Engine - Engine and crankcase 11. On the rear of the engine, remove the oil cooler tube clamp (1). Move the oil cooler lines to the side. 11 RAIL13TR04236AA 12. Disconnect the low pressure A/C line (1). Cap or plug all fittings and hoses. 12 RAIL13TR04228AA 13. Disengage the hose clamp and disconnect the engine controller oil line (1). 13 RAIL13TR04227AA 14. Removethethreemountingbolts(1)securingthefuse panel bracket. NOTE: Cut any wire ties securing the harness. 14 RAIL13TR04216AA 48115454 13/04/2017 10.1 [10.001] / 49

Engine - Engine and crankcase 15. Remove the fuse panel. 15 RAIL13TR04214AA 16. Disconnect the harness connector (1) for the engine grid heater and the power supply cable (2). 16 RAIL13TR04219AA 17. Disconnect the vent hose (1) from the intake manifold. 17 RAIL13TR04218AA 18. Disconnecttheharnessconnector(1)forthefandrive. 18 RAIL13TR04220AA 48115454 13/04/2017 10.1 [10.001] / 50

Engine - Engine and crankcase 19. Remove the A/C compressor mounting bolt (1) and disconnect the ground wire (2). 19 RAIL13TR04224AA 20. Disconnect the harness connector (1) to the A/C pres- sure switch. 20 RAIL13TR04223AA 21. Disconnect the alternator excite wire connector (1) and the CAN bus connector (2). 21 RAIL13TR04221AA 22. Remove the nut and disengage the alternator output cable (2). 22 RAIL13TR04231AA 48115454 13/04/2017 10.1 [10.001] / 51

Engine - Engine and crankcase 23. Disconnect the engine controller connector (1). 23 RAIL13TR04226AA 24. Remove the bolts (1) and cover for the drop box drive shaft. Set the cover aside. 24 RCPH10CCH813AAB 25. Mark the drive shaft (1). Remove the four bolts and disengage the drive shaft from the flywheel. 25 RCPH10CCH817AAB 26. Remove the bolts (1) from the plate (2) for the right hand rear engine mount. 26 RCPH10CCH925AAB 48115454 13/04/2017 10.1 [10.001] / 52

Engine - Engine and crankcase 27. Attach appropriately rated lifting equipment to the lift- ing brackets on the engine. engine while making certain all harnesses, lines and hoses have been disconnected. Carefully remove the 27 RAIL13TR04247AA 28. Remove the right hand rear engine mount. Inspect for wear and/or damage. Replace as required. Repeat for the left hand side. 28 RCPH07CCH166AAB 29. Remove the four bolts (1) securing the brackets (2) for the front engine mount. 30. Remove the bolt (3) securing the front engine mount (4). 31. Inspect the mount for wear and/or damage. Replace as required. 29 RCPH10CCH833AAB Next operation: Engine - Install (10.001) 48115454 13/04/2017 10.1 [10.001] / 53

Engine - Engine and crankcase Engine - Install Prior operation: Engine - Remove (10.001) 1. If removed, install the front engine mounting brackets (1). 2. Torque the four mounting bolts (2) to 101 113 N m(75 83 lb ft). 3. Torque the ISO mount support bolt nut (3) to 160 220 N m (118 162 lb ft). 4. After proper torque is achieved, back the nut (3) off one half to one full turn. 1 RCPH10CCH833AAB 5. Install the right (shown) and left rear engine ISO mounts. 2 RCPH07CCH166AAB 6. Properly support the engine. Raise and move the en- gine into the front support frame. 3 RAIL13TR04248AA 7. Install the holding plate (1) for the right rear engine mount with the bolts (2) removed earlier. 8. Torque the bolts to 125 150 N m (92.2 110.6 lb ft). 9. Install the bolts (3) removed earlier, and torque to 125 150 N m (92 111 lb ft). 10. Installthehoodsupportboltandwasher(4)andtorque to 125 150 N m (92 111 lb ft). 4 RCPH10CCH925AAB 48115454 13/04/2017 10.1 [10.001] / 54

Engine - Engine and crankcase 11. Making sure the marks (1) are aligned, attach the en- gine output drive shaft to the engine flywheel. 12. Using the four bolts (2) removed earlier to secure the drive shaft to the flywheel. 13. Torque the bolts to 101 113 N m (75 83 lb ft). 5 RCPH10CCH817AAB 14. Install the engine output drive shaft cover (1). Use the bolts (2) removed earlier to secure the cover to the flywheel housing. 6 RCPH10CCH813AAB 15. Connect the harness connector (1) to the engine con- troller. 7 RAIL13TR04226AA 16. Connect the alternator output cable (1) and secure with the nut removed previously. 8 RAIL13TR04231AA 48115454 13/04/2017 10.1 [10.001] / 55

Engine - Engine and crankcase 17. Connect the alternator excite wire connector (1) and the CAN bus connector (2). 9 RAIL13TR04221AA 18. Connect the harness connector (1) to the A/C pres- sure switch. 10 RAIL13TR04223AA 19. Connect the ground wire (1) and secure the wire with the A/C compressor mounting bolt (2). 11 RAIL13TR04224AA 20. Connect the harness connector (1) for the fan drive. 12 RAIL13TR04220AA 48115454 13/04/2017 10.1 [10.001] / 56

Engine - Engine and crankcase 21. Connect the vent hose (1) to the intake manifold. 13 RAIL13TR04218AA 22. Connect the harness connector (1) for the engine grid heater and the power supply cable (2). 14 RAIL13TR04219AA 23. Install the fuse panel. 15 RAIL13TR04214AA 24. Secure the fuse panel bracket with the three mounting bolts (1) removed previously. Secure the harness with wire ties. 16 RAIL13TR04216AA 48115454 13/04/2017 10.1 [10.001] / 57

Engine - Engine and crankcase 25. Connecttheoilline(1)andsecurewiththehoseclamp removed previously. 17 RAIL13TR04213AA 26. Lubricate a new O-ring with PAG or mineral oil and install the O-ring. Connect the low pressure A/C line (1). 18 RAIL13TR04228AA 27. On the rear of the engine, secure the oil cooler tubes with the tube clamp (1) previously removed. 19 RAIL13TR04236AA 28. Connect the front suspended axle electrical connec- tors (1) if equipped. 20 RAIL13TR04237AA 48115454 13/04/2017 10.1 [10.001] / 58

Engine - Engine and crankcase 29. Install the cover plate for the left hand rear engine mount. Torque the bolts (1) to 125 150 N m (92.2 110.6 lb ft). 21 RAIL13TR04243AA 30. Lubricate a new O-ring with PAG or mineral oil and install the O-ring; reconnect the high pressure A/C hose (1). 31. Reconnect he coolant lines (2). 22 RAIL13TR04230AA 32. Install the hood support. 23 RAIL13TR04212AA 33. Torque the bolts (1) to 125 150 N m(92.2 110.6 lb ft). 24 RAIL13TR04209AA 48115454 13/04/2017 10.1 [10.001] / 59

Engine - Engine and crankcase 34. Connect the starter cables (1) and the auxiliary wire (2). 25 RAIL13TR04209AA 35. Install a wire tie (1) to secure the harness to the hood support (2). 26 RAIL13TR04204AA 36. Install the air intake tube (1) and secure with the hose clamps (2) previously removed. 27 RAIL13TR04211AA 37. Connect the harness connectors for the humidity sen- sor (1) and the air restriction sensor (2). Connect the hose (3) to the air intake tube. Secure the hose with the hose clamp previously removed. 28 RAIL13TR04202AA Next operation: Air conditioning - Evacuate (50.200) Next operation: 48115454 13/04/2017 10.1 [10.001] / 60

Engine - Cylinder heads Valve cover - Remove - Over head components Prior operation: Hood - Remove (90.100) Prior operation: Air conditioning - Recover (50.200) Prior operation: Engine cooling system - Emptying (10.400) NOTE: During the disassembly of components with O-ring seals, it is recommended that the seals be discarded and new seal installed during assembly. NOTE: Cap all fittings and plug all lines/hoses as they are disconnected. 1. Loosen the hose clamp (1) at the air cooler inlet. 1 RAIL13TR04527AA 2. Loosen the hose clamp (1) on the opposite end of the air cooler inlet and remove the inlet tube. 2 RAIL13TR04526AA 3. Remove the oil cooler tube clamp (1). 3 RAIL13TR04534AA 48115454 13/04/2017 10.2 [10.101] / 3

Engine - Cylinder heads 4. Disconnect the hydraulic lines (1) using special tool 380000795. NOTE: Be prepared to collect some hydraulic oil by placing a pan under the fitting. 4 RAIL13TR04535AA 5. Disconnect the air conditioning high pressure hose from the tube fitting (1) and the coolant hose (2). 5 RAIL13TR04537AA 6. Remove the hydraulic tube clamp (1) from the hydraulic tube. 6 RAIL13TR04536AA 7. Remove the hydraulic cooler lines (1) on each side of the cooler ( left side shown). 7 RAIL13TR04530AA 48115454 13/04/2017 10.2 [10.101] / 4

Engine - Cylinder heads 8. Disconnect the low pressure A/C line (1), loosen the hose clamps (2) securing the overflow hose. 8 RAIL13TR04542AA 9. Disconnect the overflow hose (1) and remove the top bracket mounting bolts (2). 9 RAIL13TR04543AA 10. Remove the two mounting bolts (1) on the rear of the top bracket and remove the bracket. 10 RAIL14TR00391AA 11. Disconnect the electrical connector (1), the coolant hoses (2) and the DEF fluid line (3) from the dosing valve. 11 RAIL13TR04188AA 48115454 13/04/2017 10.2 [10.101] / 5

Engine - Cylinder heads 12. Remove the NOx sensor (1) from the exhaust pipe. 12 RAIL13TR04185AA 13. Disconnect the electrical connector (1) for the temper- ature sensor. 13 RAIL13TR04183AA 14. Disengage the clamp (1) from the exhaust pipe to the turbo. 14 RAIL13TR04177AA 15. Disengage the clamp (1) from the exhaust pipe to the Diesel oxidation catalyst (DOC) 15 RAIL13TR04180AA 48115454 13/04/2017 10.2 [10.101] / 6

Suggest: If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading

Engine - Cylinder heads 16. Remove the two nuts (1) from the C-clamp (2) secur- ing the exhaust pipe. Remove the exhaust pipe and set aside. 16 RAIL13TR04181AA 17. Disengage the clamp (1) from the outlet side of the catalyst. 17 RAIL13TR04192AA 18. Remove the two nuts (1) from the catalyst mounting straps. 18 RAIL13TR04190AA 19. Slide the catalyst forward from under the support bracket. Remove the catalyst. 19 RAIL13TR04193AA Next operation: Remove the valve cover. Next operation: 48115454 13/04/2017 10.2 [10.101] / 7

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com