Case IH Farmall 75N Farmall 85N Farmall 95N Tractors Operator’s Manual Instant Download (Publication No.84142392)

Farmall 75N, Farmall 85N, Farmall 95N Tractors Operator s Manual 11/08 84142392 1st Printing CNH America LLC, Racine, WI 53404 U.S.A. Printed in U.S.A.

TO THE OWNER This manual contains information concerning the adjustment and maintenance of your Case IH Farmall Model 75N, 85N, and 95N Tractors. You have purchased a dependable machine, but only by proper care and operation can you expect to receive the performance and long service built into this tractor. Please have all operators read this manual carefully and keep it available for ready reference. Your Case IH dealer will instruct you in the general operation of your tractor. (Refer to the Delivery Report at the back of this manual.) Your dealer s staff of factory-trained service technicians will be glad to answer any questions that may arise regarding the operation of your tractor. Your Case IH dealer carries a complete line of genuine Case IH service parts. These parts are manufactured and carefully inspected to insure high quality and accurate fitting of any necessary replacement parts. Be prepared to give your dealer the model and product identification number of the tractor, when ordering parts. Locate these numbers now and record them below. Refer to the General Information section of this manual for the location of the model and product identification numbers of your tractor. Model Product Identification Number WARNING Thissafetyalertsymbolindicatesimportantsafetymessages inthis manual.When yousee thissymbol, carefully read the message that follows and be alert to the possibility of personal injury or death. WARNING Pictures in this manual may show protective shielding open or removed to better illustrate a particular feature or adjustment. Be certain, however, to close or replace all shielding before operating the machine. IMPROVEMENTS CNH America LLC is continually striving to improve its products. We reserve the right to make improvements or changes when it becomes practical and possible to do so, without incurring any obligation to make changes or additions to the equipment sold previously. 0-1

CONTENTS Section 0 To The Owner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-1 Improvements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-1 California Proposition 65 Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-5 Section 1 General Information and Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Tractor Identification Plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Important Ecological Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Precautionary Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6 Personal Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6 Machine Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6 Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6 Working Safely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8 Safety Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14 Standardized Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19 Tractor Noise Level Information Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20 Section 2 General Information, Controls and Instruments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Digital Instrument Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Digital Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Indicator Light Panel Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24 Cab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28 Air-conditioning/Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33 Cab Air-conditioning/Heating Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-34 Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-42 Transmission with Range Gear and Mechanical Shuttle 30/40 Km/h (16F + 16R) . . . . . . . . . . . . . . . . . . . . 2-44 Transmission with Range Gear and Electrohydraulic Shuttle 30/40 Km/h (16FWD + 16REV) . . . . . . . . . . 2-45 18.64 mph (30 Km/h) Transmission Version (16FWD + 16REV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-46 0-2

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com

Section 3 Field Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Starting and Stopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6 Electronically Controlled Electro--hydraulic MFD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8 Differential Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9 Power Take--off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11 Mechanically Controlled Hydraulic Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14 Three--point Linkage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18 Implement Connection Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22 Auxiliary Control Valves (Use and Maintenance) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23 Rear Remote Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26 Wheel Track Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-29 Mfd Front and Rear Wheel Track Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-31 Steering Angle Adjustment (MFD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32 Front Axle Swing Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-35 Loading Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-37 Speed Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-37 Inflation Pressures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-38 Tire Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-39 Tire Combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-40 Metal Ballasting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-41 Permitted Maximum Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-42 MFD Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-44 Section 4 Lubrication and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Tractor Refueling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Access for Inspection and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6 Lubrication and Maintenance Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Flexible Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9 When the Indicator Light Illuminates on the Dashboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13 Every 10 Hours of Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16 Every 50 Hours of Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17 Every 100 Hours of Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20 Every 300 Hours of Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22 Every 500 Hours of Work (Models 75N and 85N) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26 Every 600 Hours of Work (Model 95N) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29 0-3

Every 1200 Hours or Every Year . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-32 Every 1200 Hours of Work or Every 2 Years . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34 Every 1800 Hours of Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-38 Electrical System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-39 Starting The Engine with a Flat Battery or No Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-40 Fuses and Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-41 Location of Fuses and Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-42 Front Headlight Adjustment and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-59 Recommendations For Bodywork Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-70 Lubricants and Fluids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-71 Section 5 Troubleshooting, Causes and Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Section 6 Prolonged Tractor Inactivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 Section 7 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 Towing Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Fold-down Roll Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Section 8 Specifications and Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Engine Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6 Section 9 Inspections and/or Operations to be Carried Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1 Section 10 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1 0-4

(North America Only) (California Only) CALIFORNIA Proposition 65 Warning Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm. Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. 0-5

SECTION 1 GENERAL INFORMATION AND SAFETY GENERAL This Use and Maintenance Manual provides a guide for the user with regard to running-in, use and maintenance of the tractor. Safety precautions for the operator and bystanders are shown on the following pages. Read the safety instructions and follow recommendations and hints before starting to use the tractor. Read this manual carefully and keep in a convenient place for future reference. Do not hesitate to contact your local dealer for any queries concerning your tractor. The dealer can provide skilled personnel, trained by the manufacturer, original service parts and all tools and equipment necessary for your service requirements. SERVICE AFTER THE FIRST 50 HOURS OF WORK The operations required for the first service are shown at the end of the Manual, immediately prior to the index. Afterthefirst50hoursofuse,returntothedealerwith your tractor and this Manual in order to carry out the Manufacturer s checks and to fill in the certificates included in Section 9. The first sheet must be compiled on completion of the service and held by the dealer. The second sheet must be kept in the Manual for documentation and reference purposes. Check that both copies are signed by both yourself and the dealer. The tractor is designed as a power generator and drive-propulsion unit for use in normal and traditional agricultural conditions. The tractor is also designed to provide maximum performance, economic running and easy use over a wide range of operations. Prior to delivery, all machines are carefully inspected (by both the Manufacturer and your local authorized dealer), to make sure that they reach the user in perfect condition.Tomaintainthetractorinthisconditionand ensure trouble-free operation, the routine mainte- nance described in Section 3 of this manual must be carried out at the specified intervals. SPARE PARTS Non-original spare parts have not been tested or authorized by the Manufacturer. Installment and/or use of such products may adversely affect the tractor s design specifications, thereby compromis- ing operational safety. The manufacturer cannot be held responsible for any damage resulting from the use of non-original spare parts. CLEANING THE TRACTOR Your tractor is an advanced machine, fitted with an electro-hydrauliccontrolsystem.Caremustbetaken when cleaning the tractor, especially if a pressurized water cleaner is used. No modifications may be made to the tractor without written authorization from the Manufacturer. When using a pressure washer, never stand too close to the tractor or direct the water jet on electrical components, seals or intake openings, etc. WARRANTY The tractor is guaranteed in accordance with current legislation in your country and in line with contractual agreements reached with the dealer at the time of sale. However, the warranty is no longer valid if the rulesandinstructionsfortheuseandmaintenanceof the tractor, described in this Manual, are not observed. Never direct jets of cold water at the hot engine or exhaust. See also Section 3 (Recommenda- tions for bodywork maintenance). SAFETY PRECAUTIONS 1-1

SECTION 1 - GENERAL INFORMATION AND SAFETY TRACTOR IDENTIFICATION PLATES Serial numbers identify the tractor and its main components. The identification data must be supplied by the dealer for requests for spare parts or service operations. Identification data is of fundamental importance in the event of theft of the tractor. The location of the various identification data is shown below. ENGINE IDENTIFICATION DATA PLATE The tractor s frame number is stamped over thefront support, 1. It gives the safety frame identification data. Record below the corresponding serial number. 1 FRAME AND ENGINE TYPE IDENTIFICATION SUMMARY DATA PLATE FOR MODELS WITH ROLL BAR The plate, 1, groups the identification data with your machine s frame number and engine number. Record below the corresponding serial number. 2 FRAME AND ENGINE TYPE IDENTIFICATION SUMMARY DATA PLATE FOR MODELS WITH CAB The plate, 1, groups the identification data with your machine s frame number and engine number. Record below the corresponding serial number. 3 1-2

SECTION 1 - GENERAL INFORMATION AND SAFETY ENGINE IDENTIFICATION DATA PLATE (MODELS 75N AND 85N) The serial number of the engine fitted on the tractor is stamped on the left--hand side of the engine body. Record below the corresponding serial number. 4 ENGINE IDENTIFICATION DATA PLATE (MODEL 95N) The plate with the engine data installedon thetractor is fitted on the right--hand side of the engine. Record below the corresponding serial number. 5 MFD FRONT AXLE IDENTIFICATION PLATE The plate, 1, is located on the right--hand side and gives the identification data for the axle fitted on the machine. Record below the corresponding serial number. 6 1-3

SECTION 1 - GENERAL INFORMATION AND SAFETY ROLL BAR IDENTIFICATION PLATE The plate, 1, is located on the right--hand side and gives the identification data for the framefitted onthe machine. Record below the corresponding serial number. 7 CAB IDENTIFICATION PLATE The cab identification plate is located at the rear on the left--hand side as shown in the figure. Record below the corresponding serial number. 8 1-4

SECTION 1 - GENERAL INFORMATION AND SAFETY IMPORTANT ECOLOGICAL CONSIDERATIONS Soil, air and water are essential elements for agriculture and for life on in general. If local legislation does not control the treatment of certain substances, the production of which is necessitated by advanced technologies, products derived from chemical and petrochemical products must be used and disposed of according to the rules of common sense. 4. Avoid spillage when transferring used engine cooling liquids, engine and transmission lubri- cants, hydraulic oils, brake fluids, etc. Never mix used brake oil with fuel oil, or fuel oil with lubricants. Store safely until suitable disposal can be arranged according to nationallegislation or local regulations. 5. Modern anti-freeze liquids and solutions, e.g. anti-freezeandotheradditives,mustbereplaced every two years. They must not be left to be absorbed into the ground, but must be collected and disposed of in a suitable manner. The following recommendations may be of help: Find out what the relevant legislation in your country stipulates. Ask your suppliers of lubricants, oils, fuels, anti-freeze, detergents, etc. for information on the effects of these products on humans and the environment and for instructions concerning their use, storage and disposal. In many cases, local agricultural consultants will be able to provide assistance. 6. Do not open the air conditioning systems to carry out work. These systems contain gas which must not be released into the atmosphere. Contact your dealer or specialized personnel, who are equipped with the appropriate equipment and are authorized to refill the system. 7. Any leakage or defect in the engine cooling or hydraulicsystemsmustberepairedimmediately. SUGGESTIONS 1. Avoid systems or fuel cans when filling tanks, as these may cause considerable spillage and leakage of liquids. 8. Do not increase the pressure in pressurized systems, as this may cause component parts to burst. using unsuitable, pressurized filling 9. When welding, make sure that hoses are properly protected as sparks or molten material may puncture or weaken the tubes and sleeves, resulting in leakage of oil, cooling liquid, etc. 2. As a general rule, do not allow liquid fuels, lubricants, acids, solvents, etc., to come into contact with the skin. The majority of these products contain substances that are potential health hazards. 10. Do not adjust the setting of the fuel delivery system as this will alter the emission of exhaust fumes. 3. Modern lubricants contain additives. Do not burn contaminated fuel oils and/or oils used in conventional heating systems. NOTE: The engines installed on the tractors comply with anti-pollution legislation. 1-5

SECTION 1 - GENERAL INFORMATION AND SAFETY PRECAUTIONARY STATEMENTS PERSONAL SAFETY Throughout this manual and on machine decals, you will find precautionary statements ( DANGER , WARNING ,and CAUTION )followedbyspecificinstructions.Theseprecautionsareintendedforthepersonal safety of you and those working with you. Please take the time to read them. DANGER Thisword DANGER indicatesanimmediatehazardoussituationthat,ifnotavoided,willresultindeath or serious injury. The color associated with Danger is RED. WARNING This word WARNING indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury. The color associated with Warning is ORANGE. CAUTION Thisword CAUTION indicatesapotentiallyhazardoussituationthat,ifnotavoided,mayresultinminor or moderate injury. It may also be used to alert against unsafe practices. The color associated with Caution is YELLOW. FAILURE TO FOLLOW THE DANGER , WARNING , AND CAUTION INSTRUCTIONS MAY RESULT IN DEATH OR SERIOUS BODILY INJURY. MACHINE SAFETY The precautionary statement ( IMPORTANT ) is followed by specific instructions. This statement is intended for machine safety. IMPORTANT: The word IMPORTANT is used to inform the reader of something he needs to know to prevent minor machine damage if a certain procedure is not followed. INFORMATION NOTE: Instructions used to identify and present supplementary information. ASAE S441.3 FEB04 ISO 11684 VERSION -- FEB 08 1-6

SECTION 1 - GENERAL INFORMATION AND SAFETY IMPORTANT NOTES The machine is designed and produced exclusively for agricultural use. OPERATOR PROTECTIVE STRUCTURE WARNING Your machine is equipped with an operator Protective Structure, Protective Structure (ROPS) or Falling Object ProtectiveStructure(FOPS)orCabwith ROPS.A ROPS may be a cab frame or a two-posted or four-posted structure used for the protection of the operator to minimize the possibility of serious injury. The mounting structure and fasteners forming the mounting connection with the machine are part of the ROPS. such as: a Rollover All other use will be considered to be contrary to the usespecifiedbyCNHAMERICALLC,whocannotbe held liable for damage to property or the machine, or for personal injuries which may result. Personswhoriskimproperusewillthereforeassume the responsibility for any consequences arising from such use. Compliance maintenance and repairs described in this manual, are the essential preconditions for the use specified by CNH AMERICA LLC. with the instructions for use, The Protective Structure is a special safety component of your machine. DO NOT attach any device to the Protective Structure for pulling purposes. DO NOT drill holes to the Protective Structure. Themachinemustonlybeused,servicedorrepaired bypersonneltrainedintherelevantworkingmethods and safety regulations authorized to work on the machine. The Protective Structure and interconnecting components area certifiedsystem. Anydamage, fire, corrosion or modification will weaken the structure and reduce your protection. If this occurs, the Protective Structure MUST be replaced so that it will provide the same protection as a new Contact your dealer for Protective Structure inspection and replacement. and who have been The user must also observe the rules concerning generalsafetyandaccidentprevention,includingthe Highway Code when driving on public highways. Protective Structure. Any arbitrary modifications made to this machine will release CNH AMERICA LLC from any liability resulting from damage or injury. After an accident, fire, tip or roll over, the following MUST be performed by a qualified technician before returning the machine to field or job site operation: CNH organizations, inclusive of, but not restricted to, national,regionalorlocaldistributors,cannot beheld liable for damage resulting from the malfunction of parts and/or components not approved by CNH AMERICA LLC. AMERICA LLC and all its distribution The Protective Structure MUST be replaced. The mounting or Protective Structure, suspension, seat belts components and wiring within the operator s protective system inspected for damage. All damaged parts MUST be replaced. suspension operator for the and seat mounting and Under no circumstances will a guarantee be issued for products made or sold by CNH AMERICA LLC that are damaged as a result of the malfunction of parts and/or components not approved by CNH AMERICA LLC. MUST be carefully DO NOT WELD, DRILL HOLES, ATTEMPT TO STRAIGHTEN OR REPAIR THE PROTECTIVE STRUCTURE. MODIFICATION IN ANY WAY CAN REDUCETHESTRUCTURALINTEGRITY OFTHE STRUCTURE WHICH COULD CAUSE DEATH OR SERIOUS INJURY IN THE EVENT OF FIRE, TIP, ROLLOVER, COLLISION OR ACCIDENT. 1-7

SECTION 1 - GENERAL INFORMATION AND SAFETY WORKING SAFELY 1. During the manufacturing of this tractor, every step has been taken to ensure safe operation. However, the best way to avoid accidents is to exercise caution at all times. Once the accident has already happened it is too late to remember what steps should have been taken. 6. It is advisable to keep a first aid kit on hand. 7. The tractor must only be used by responsible personnel, trained intractor useand authorizedto operate the machine. 8. Do not alter the injection system calibration in an attempt to increase maximum engine speed. 2. ReadthisManualcarefullybeforestarting,using, carrying out maintenance, refuelling or perform- ing any other type of operation on the tractor. 3. The time spent reading this Manualwillallowyou to get to know your tractor, thereby saving time and effort. This will also help prevent accidents from taking place. 4. Read all the safety decals on the machine and follow the instructions thereon before starting, operating, refuelling or carrying out maintenance on the machine. Promptly replace any decals that are damaged, lost or illegible. Clean the decals if they are covered by mud or debris. 9 5. Remember designed for agricultural use. Any other use will require prior authorization from CNH America LLC. that the tractor is exclusively 9. Do not wear loose clothing that may be trapped in moving parts. Check that all rotating parts connected to the power take-off are correctly protected. 10. Do not alter the calibration of the pressure relief valves in the various hydraulic circuits (hydro- static steering, hydraulic lift, auxiliary control valves, etc.). 1-8

SECTION 1 - GENERAL INFORMATION AND SAFETY 11. Avoid using the tractor in unsuitable physical conditions, stop work instead. 17. Never start or maneuver the tractor unless seated in the driving position. 12. Enter and leave the tractor using the steps and handlesprovided.Keepthesefittingsfreeofmud and debris. 13. Always operate with the cab or roll bar correctly and securely fitted on the tractor: periodically check that the fittings are not loose and that all parts of the structure are free from any damage and deformation. Do not modify the roll bar by welding parts, drilling holes, etc., as this could adversely affect the rigidity of the structure. 24135 STARTING THE TRACTOR 14. Before starting the engine, check that the hand brake is onand thatthe gearsand powertake-off are disengaged, even if the tractor is fitted with a start-up safety device. Never disconnect the start-upsafetyswitch.Iftheswitchdoesnotwork correctly, contact your local dealer for eventual repair operations. 10 18. Before moving the tractor, always check that the area is free of persons or obstacles. 15. Before starting the engine, make sure that all attached implements are lowered to the ground. 16. Before starting the engine, check that all covers andguardsarecorrectlyinposition(rollbar,hood side panels, power take-off guard, front axle transmission shaft cover, etc.). 24134 11 19. Never run the engine in a closed space without ensuring adequate ventilation. Exhaust fumes are damaging to the health and can be lethal. 1-9

SECTION 1 - GENERAL INFORMATION AND SAFETY USING THE TRACTOR 20. Select the most suitable wheel setting for the work in hand, i.e., the setting that provides the best stability. 22. When travelling downhill, keep the tractor in gear. Never release the clutch and never leave the gears in neutral. 23. When the tractor is moving, the operator must remain correctly seated in the driving position. 24. Nevergetonoroffthetractorwhileinmovement. 25. When using the brakes, press the pedal down slowly. 26. Avoid curving at high speeds. 27. Always use the tractor at a speed that will guarantee safe operation on the type of land being worked. When working on uneven ground, use maximum care to ensure proper stability. 24136 12 28. If you have to work with the tractor on a gradient, forexampleonhillsides,driveatmoderatespeed especially when taking curves. 21. Engage the clutch slowly: if engaged too quickly, especially when the tractor is getting out of a hole, ditch or operating on muddy ground or steep slopes, the tractor may overturn. Release the clutch immediately if the front wheels start to lift. 24137 14 29. Proceed with maximum caution when working with the wheels near the edge of ditches or slopes. 24223 13 30. When driving on public highways, observe the Highway Code. 1-10

SECTION 1 - GENERAL INFORMATION AND SAFETY 31. When driving, do not rest your feet on the brake or clutch pedals. 24139 16 38. When towing, do not negotiate bends with the differentiallockengagedasthismay preventyou from steering the tractor. 24138 15 32. Never carry passengers, not even inside the cab, unless the machine is fitted with an approved extra seat. USING IMPLEMENTS AND AGRICULTURAL MACHINERY 39. Do not connect implements or machinery that require more power than can be generated by your tractor model. 33. Whendrivingonroads,connectthebrakepedals using the plate provided. Braking when the pedalsare notconnected couldcause thetractor to skid. Avoid excessive wear on the brakes by using engine braking. 40. Never negotiate sharp bends with the power take-offunderaheavyload;thismaydamagethe universal joints on the transmission shaft connected to the power take-off. TOWING AND TRANSPORT 41. Never stand between the reversing tractor and the implement when hitching. 34. To guarantee tractor stability when moving, adjust the hitching device according to the trailer or implement to be used. 35. Driveslowlywhentowingextremelyheavyloads. 36. For your own safety, do not tow trailers that are not fitted with an independent braking system. 37. If the tractor is used to tow heavy loads, always use the hitching device and never hitch loads onto the lower arms or the top link of the three-point linkage. This may result in tipping or overturning. 1-11

Suggest: If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading

SECTION 1 - GENERAL INFORMATION AND SAFETY 42. When using implements that require the tractor tobestationarywiththeenginerunning,keepthe gear and range levers in the neutral position, apply the hand brake and use suitable wheel chocks. slopes, in addition to applying the hand brake, put the tractor in first gear when facing downhill. As an additional safety measure, use wheel chocks (available as an optional); this procedure iscompulsorywhenparkingwithatrailerhitched. CAUTION When using the Dual Command (2 Speed Power Shift) with the tractor parked and the engine switched off, the shuttle lever must be moved to the reverse position. 24143 17 43. Donotoperatemachinesconnectedtothepower take-off without first ensuring that the operating range of the machine is free of bystanders. Alsocheckthatallrotatingpartsconnectedtothe power take-off shaft are correctly protected. 24140 18 44. Add rear ballast when using lifting equipment fitted to the front of the tractor. SERVICING THE TRACTOR STOPPING THE TRACTOR CAUTION InthisManual,someillustrationsshowpanelsor covers removed in order to facilitate explana- tions. Never use the tractor without the panels or guards in place. 45. When the tractor is stationary, never leave connected implements in the raised position. All implements must be loweredbefore stoppingthe engine. 46. Before leaving the driving position, move the gear lever to the neutral position, disengage the power take-off, apply the hand brake, stop the engine and put the tractor in gear. 48. Do not work on the tires with unsuitable equipment or without the necessary experience. Incorrect tire fitting may put safety at risk. If in doubt, contact skilled personnel. Always remove the ignition key from the dashboard when leaving the tractor unattended. 49. When changing or storing tires, make sure they are stacked correctly and cannot roll or topple over causing personal injury. 47. Park on flat surfaces, where possible, put the tractor into gear and apply the hand brake. On 1-12

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com