CASE 821F XR Wheel Loader Service Repair Manual Instant Download

SERVICE MANUAL 821F 921F 821F 921F Stage IV Wheel Loader Wheel Loader 1/2 SERVICE MANUAL Part number 47969425 Part number 47969425 English November 2015 2015 CNH Industrial Italia S.p.A. All Rights Reserved.

SERVICE MANUAL 821F XR 821F ZBAR 921F XR 921F ZBAR 47969425_EN 29/01/2016 EN

Link Product / Engine Product Market Product Europe Engine 821F XR WHEEL LOADER TIER 4B 821F ZBAR WHEEL LOADER TIER 4B 921F XR WHEEL LOADER TIER 4B 921F ZBAR WHEEL LOADER TIER 4B F4HFE613S*B004 Europe F4HFE613S*B004 Europe F4HFE613R*B006 Europe F4HFE613R*B006 47969425_EN 29/01/2016

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com

Contents INTRODUCTION Engine....................................................................................... 10 [10.001] Engine and crankcase ............................................................. 10.1 [10.202] Air cleaners and lines .............................................................. 10.2 [10.500] Selective Catalytic Reduction (SCR) exhaust treatment........................... 10.3 [10.400] Engine cooling system ............................................................. 10.4 [10.414] Fan and drive ...................................................................... 10.5 [10.310] Aftercooler.......................................................................... 10.6 [10.304] Engine lubrication system.......................................................... 10.7 Transmission.............................................................................. 21 [21.113] Powershift transmission ............................................................ 21.1 [21.155] Powershift transmission internal components...................................... 21.2 [21.700] Torque converter ................................................................... 21.3 Four-Wheel Drive (4WD) system .................................................. 23 [23.314] Drive shaft.......................................................................... 23.1 Front axle system ....................................................................... 25 [25.100] Powered front axle ................................................................. 25.1 [25.102] Front bevel gear set and differential ............................................... 25.2 [25.108] Final drive hub, steering knuckles, and shafts ..................................... 25.3 Rear axle system........................................................................ 27 [27.100] Powered rear axle.................................................................. 27.1 [27.106] Rear bevel gear set and differential................................................ 27.2 [27.120] Planetary and final drives .......................................................... 27.3 Brakes and controls .................................................................... 33 [33.202] Hydraulic service brakes ........................................................... 33.1 [33.110] Parking brake or parking lock ...................................................... 33.2 47969425_EN 29/01/2016

Hydraulic systems....................................................................... 35 [35.000] Hydraulic systems.................................................................. 35.1 [35.300] Reservoir, cooler, and filters........................................................ 35.2 [35.106] Variable displacement pump ....................................................... 35.3 [35.357] Pilot system ........................................................................ 35.4 [35.752] Hydraulic fan drive cooling system................................................. 35.5 [35.355] Hydraulic hand control ............................................................. 35.6 [35.724] Front loader hydraulic system control.............................................. 35.7 [35.701] Front loader arm hydraulic system................................................. 35.8 [35.723] Front loader bucket hydraulic system.............................................. 35.9 [35.734] Tool quick coupler hydraulic system ............................................. 35.10 Frames and ballasting................................................................. 39 [39.100] Frame .............................................................................. 39.1 Steering..................................................................................... 41 [41.101] Steering control .................................................................... 41.1 [41.200] Hydraulic control components...................................................... 41.2 [41.216] Cylinders ........................................................................... 41.3 [41.910] Auxiliary steering................................................................... 41.4 Wheels...................................................................................... 44 [44.511] Front wheels........................................................................ 44.1 [44.520] Rear wheels........................................................................ 44.2 Cab climate control..................................................................... 50 [50.200] Air conditioning..................................................................... 50.1 Electrical systems....................................................................... 55 [55.100] Harnesses and connectors......................................................... 55.1 [55.301] Alternator........................................................................... 55.2 [55.302] Battery.............................................................................. 55.3 47969425_EN 29/01/2016

[55.011] Fuel tank system ................................................................... 55.4 [55.988] Selective Catalytic Reduction (SCR) electrical system ............................ 55.5 [55.989] Exhaust Gas Recirculation (EGR) electrical system ............................... 55.6 [55.012] Engine cooling system ............................................................. 55.7 [55.519] Cab brake controls ................................................................. 55.8 [55.030] Service brake electrical system .................................................... 55.9 [55.031] Parking brake electrical system.................................................. 55.10 [55.512] Cab controls...................................................................... 55.11 [55.051] Cab Heating, Ventilation, and Air-Conditioning (HVAC) controls................. 55.12 [55.050] Heating, Ventilation, and Air-Conditioning (HVAC) control system............... 55.13 [55.047] Steering control system .......................................................... 55.14 [55.530] Camera........................................................................... 55.15 [55.518] Wiper and washer system........................................................ 55.16 [55.514] Cab lighting ...................................................................... 55.17 [55.408] Warning indicators, alarms, and instruments .................................... 55.18 [55.DTC] FAULT CODES.................................................................. 55.19 Front loader and bucket............................................................... 82 [82.300] Bucket.............................................................................. 82.1 Platform, cab, bodywork, and decals............................................. 90 [90.150] Cab................................................................................. 90.1 [90.156] Cab glazing ........................................................................ 90.2 [90.114] Operator protections ............................................................... 90.3 47969425_EN 29/01/2016

INTRODUCTION 47969425_EN 29/01/2016 1

INTRODUCTION Safety rules Personal safety This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible death or injury. Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in- structions. These precautions are intended for the personal safety of you and those working with you. Read and understand all the safety messages in this manual before you operate or service the machine. DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury. WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury. CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury. FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT IN DEATH OR SERIOUS INJURY. Machine safety NOTICE: Notice indicates a situation that, if not avoided, could result in machine or property damage. Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or property damage. The word Notice is used to address practices not related to personal safety. Information NOTE: Note indicates additional information that clarifies steps, procedures, or other information in this manual. Throughout this manual you will find the word Note followed by additional information about a step, procedure, or other information in the manual. The word Note is not intended to address personal safety or property damage. 47969425_EN 29/01/2016 3

INTRODUCTION Personal safety Carefully read this Manual before proceeding with main- tenance, repairs, refuelling or other machine operations. Repairs have to be carried out only by authorized and in- structed staff; specific precautions have to be taken when grinding, welding or when using mallets or heavy ham- mers. Non-authorized persons are not allowed to repair or carry out maintenance on this machine. Do not carry out any work on the equipment without prior authorization. Ask your employer about the safety instructions in force and safety equipment. 1 TULI12WEX2004AA Nobody should be allowed in the cab during machine maintenance unless he is a qualified operator helping with the maintenance work. If it is necessary to move the equipment to carry out re- pairs or maintenance, do not lift or lower the equipment from any other position than the operator s seat. Never carry out any operation on the machine when the engine is running, except when specifically indicated. Stop the engine and ensure that all pressure is relieved from hydraulic circuits before removing caps, covers, valves, etc. All repair and maintenance operations should be carried out with the greatest care and attention. Service stairs and platforms used in a workshop or in the field should be built in compliance with the safety rules in force. 2 TULI12WEX2005AA Any functional disorders, especially those affecting the safety of the machine, should therefore be rectified im- mediately. DANGER Unexpected movement! Make sure parking brake is applied. Secure machine with wheel chocks. Failuretocomplywillresultindeathorserious injury. D0013A Before performing any work on the machine, attach a maintenance in progress tag. This tag can be applied on the left-hand control lever, safety lever or cab door. 47969425_EN 29/01/2016 4

INTRODUCTION Product identification 1 LEIL15WHL0056FA 1. Bucket 2. Loader lift arms (Z-bar version) 3. Driving lights 4. Roll Over Protection System (ROPS) cab 5. Precleaner 6. Engine and Selective Catalyst Reduction (SCR) system 7. Counterweight 8. Electric master switch and battery jump post (optional) 9. Steps 47969425_EN 29/01/2016 24

INTRODUCTION 2 LEIL13WHL0214FA 5. Bucket cylinder 6. Front frame 7. Rear frame 8. Steps 1. Diesel Exhaust Fluid (DEF) fill tank 2. Sliding access panel 3. Fuse access door 4. Cab air filter 47969425_EN 29/01/2016 25

SERVICE MANUAL Engine 821F XR 821F ZBAR 921F XR 921F ZBAR 47969425_EN 29/01/2016 10

Engine - Engine and crankcase Engine - General specification Engine with 4 Speed Transmission A. Low idle Alternate low idle Alternate Accelerated Idle B. Maximum No Load RPM C. Converter Stall D. Hydraulic Stall E. Converter & Hydraulic Stall Temperature of the torque converter oil Temperature of the hydraulic oil 870 RPM to 930 RPM 670 RPM to 730 RPM 1270 RPM to 1330 RPM 2065 RPM to 2185 RPM 1855 RPM to 2055 RPM 2065 RPM to 2265 RPM 1550 RPM to 1750 RPM 82 - 104 C (180 - 219 F) 54 - 57 C (129 - 135 F) Engine with 5 Speed Transmission A. Low idle Alternate low idle Alternate Accelerated Idle B. Maximum No Load RPM C. Converter Stall D. Hydraulic Stall E. Converter & Hydraulic Stall Temperature of the torque converter oil Temperature of the hydraulic oil 870 RPM to 930 RPM 670 RPM to 730 RPM 1270 RPM to 1330 RPM 2065 RPM to 2185 RPM 1912 RPM to 2112 RPM 2070 RPM to 2270 RPM 1590 RPM to 1790 RPM 82 - 104 C (180 - 219 F) 54 - 57 C (129 - 135 F) NOTE: Hydraulic Stall and Converter & Hydraulic Stall RPM values are read while the lift arms are rising with the bucket held rolled back and the engine at Wide Open Throttle (WOT) in max power mode with transmission in manual mode and in 3rd gear. Engine - General specification Engine with 4 Speed Transmission A. Low idle Alternate low idle Alternate Accelerated Idle B. Maximum No Load RPM C. Converter Stall D. Hydraulic Stall E. Converter & Hydraulic Stall Temperature of the torque converter oil Temperature of the hydraulic oil 870 RPM to 930 RPM 670 RPM to 730 RPM 1270 RPM to 1330 RPM 2115 RPM to 2200 RPM 1835 RPM to 2035 RPM 2075 RPM to 2275 RPM 1560 RPM to 1760 RPM 82 - 104 C (180 - 219 F) 54 - 57 C (129 - 135 F) Engine with 5 Speed Transmission A. Low idle Alternate low idle Alternate Accelerated Idle B. Maximum No Load RPM C. Converter Stall D. Hydraulic Stall E. Converter & Hydraulic Stall Temperature of the torque converter oil Temperature of the hydraulic oil 870 RPM to 930 RPM 670 RPM to 730 RPM 2170 RPM to 1330 RPM 2115 RPM to 2200 RPM 1837 RPM to 2037 RPM 2127 RPM to 2327 RPM 1560 RPM to 1760 RPM 82 - 104 C (180 - 219 F) 54 - 57 C (129 - 135 F) NOTE: Hydraulic Stall and Converter & Hydraulic Stall RPM values are read while the lift arms are rising with the bucket held rolled back and the engine at Wide Open Throttle (WOT) in max power mode with transmission in manual mode and in 3rd gear. 47969425_EN 29/01/2016 10.1 [10.001] / 3

Engine - Engine and crankcase Engine - General specification Engine Service Manual The table below lists the part numbers of the Engine FPT F4HFE613 Service Manual. The part numbers of the Eu- ropean languages related to this manual are reported. See the Engine Service Manual for more details about the engine overhaul. Language English French German Italian Spanish Engine Service Manual P/N 47606122 47606125 47606126 47606127 47606130 47969425_EN 29/01/2016 10.1 [10.001] / 4

Engine - Engine and crankcase Engine - Remove NOTE: Emissions sensors mounted in the exhaust stream are sensitive to extreme vibrations. Use of tools that gen- erate extreme vibrations, such as impact wrenches and hammers, will result in damage to emission sensors. Avoid using these tools during any service procedure in close proximity of emission sensors. If the use of these tools cannot be avoided, remove the sensors using extreme caution prior to performing any service procedure. 1. Park machine on a level surface and lower the bucket to the ground. Put articulation lock in LOCKED position and stop the engine. 1 RCPH10WHL063BAL 2. Actuate the brake pedal several times to discharge brake accumulators. 2 RCPH10WHL435AAH 3. Put key switch in ON position. Pilot control switch must be in the ON position and then move loader control lever(s) back and forth at least 30 times to release any pressure from hydraulic circuit. Put key switch in OFF position. 3 RCPH10WHL119BAL 47969425_EN 29/01/2016 10.1 [10.001] / 5

Engine - Engine and crankcase 4. Raise grill located above the cooler box just behind the cab. Then slowly loosen the hydraulic reservoir filler cap to release pressure in the reservoir. 4 RCPH10WHL099BAL 5. Locate the master and hood raise switch by the battery box. Then raise the hood and put the master discon- nect switch in the OFF position. 5 RCPH10WHL106AAH 6. Unhook the rubber T-handle (1) and raise the upper panel (2). Make sure that the security levers are blocked. 6 LEIL13WHL0137AB 7. Raise both side panels (1). Then remove the thumb screws (2) and inner fender panels (3). NOTE: right-hand side of the machine is shown. The op- eration is similar for the left side. 7 LEIL13WHL0612AB 47969425_EN 29/01/2016 10.1 [10.001] / 6

Engine - Engine and crankcase 8. Place a suitable container below radiator drain, remove radiator cap and coolant drain plug (arrow) to drain en- gine coolant. Then reinstall drain plug and radiator cap after coolant has drained. NOTE: See machine specifications for cooling system vol- ume. 8 RCPH10WHL054BAL 9. Place a suitable container below engine oil drain. Re- move drain plug and drain oil into container. Then re- install drain plug. NOTE: See machine specifications for engine oil sump vol- ume. 9 RCPH10WHL054BAL 10. After oil drains, disconnect drain hose from frame by removing jam nut (1). Then pull hose from frame in preparation for engine removal. (2) 10 RAPH12WEL0598AA 11. Double up a nylon lifting strap and slide through the exhaust stack (1) on the hood. 11 LEIL13WHL0552AB 47969425_EN 29/01/2016 10.1 [10.001] / 7

Engine - Engine and crankcase 12. Place a bar or pipe through the strap loop inside the hood and attach the strap to a suitable lifting device. Then raise the hood with the strap to release tension on the lifting motor. 12 RAPH12WEL0600AA 13. Tag and disconnect the rearview camera wire harness (if machine is equipped with a rearview camera). 13 RAPH12WEL0601AA 14. Cut wire ties and remove rearview camera wire har- ness from hood. Then place it off to the side in a safe location. (If machine is equipped with a rearview cam- era.) 14 LEIL13WHL0140AB 15. Remove hood wire harness clamp (1) from the cooler housing. Then tag and remove the hood ground wire (2) from cooler housing. 15 LEIL13WHL0149AB 47969425_EN 29/01/2016 10.1 [10.001] / 8

Engine - Engine and crankcase 16. Taganddisconnecthoodwiringharnessconnector(1) from rear chassis wiring harness connector. Remove hood wire harness clamp (2) from the fan shroud. 16 LEIL13WHL0150AB 17. Have another person to balance the hood and LOOSEN the hood hinge mounting bolts (arrows) from the cooler frame. NOTE: Do not remove the hood hinge mounting bolts at this time. 17 LEIL13WHL0142AB 18. Remove the pin from the bottom of the lifting motor cylinder where it attaches to the loader frame. 18 RAPH12WEL0606AA 19. Put the master disconnect switch in the ON position. Then, retract the lifting motor cylinder (2), replace pin and disconnect wiring harness (1). 19 RAPH12WEL0062AA 47969425_EN 29/01/2016 10.1 [10.001] / 9

Engine - Engine and crankcase 20. Put master disconnect switch (1) in OFF position. Re- move the battery cover and disconnect ground lead from the batteries (2). You may replace battery cover if desired to give you a place to stand. 20 RAPH12WEL0608AA 21. Have another person to balance the hood and re- move the hood hinge mounting bolts (arrows) from the cooler frame. 21 LEIL13WHL0142AB 22. Carefully raise and remove hood from loader. Lower hood onto suitable platform and disconnect lifting equipment from exhaust stack (1) . NOTE: Radiator overflow hose may interfere with left hand hood hinge movement and hood removal. 22 LEIL13WHL0552AB 23. Tag and disconnect engine wiring harness connector from air filter restriction switch. 23 RAPH12WEL0610AA 47969425_EN 29/01/2016 10.1 [10.001] / 10

Engine - Engine and crankcase 24. Tag and disconnect engine wiring harness connector from air inlet humidity sensor (1). 24 LEIL13WHL0143AB 25. Loosen clamp (1) on the crankcase ventilation hose (2) and disconnect hose. 25 LEIL13WHL0144AB 26. Loosen clamps on turbocharger and air filter hous- ing. Then remove the intake air hose (1) . Cover tur- bocharger inlet to prevent debris entry. 26 LEIL13WHL0145AB 27. Loosen the clamp from the elbow connected to the turbocharger. 27 LEIL14WHL0203AB 47969425_EN 29/01/2016 10.1 [10.001] / 11

Engine - Engine and crankcase 28. Loosen the clamp on the hose at the after cooler inlet and remove the tube. 28 LEIL13WHL0147AB 29. Loosenclampontheairinlethoseattheairfilterhous- ing. 29 LEIL13WHL0148AB 30. Loosen the clamp (1) on the air inlet hose (2) at the exhaust support bracket. Remove the air inlet hose (2). 30 LEIL13WHL0151AB 31. Remove the four bolts securing the air filter housing to the mounting support bracket. Then remove the air filter housing. 31 LEIL13WHL0153AB 47969425_EN 29/01/2016 10.1 [10.001] / 12

Engine - Engine and crankcase 32. Remove the four mounting bolts from the belt cover. Then remove the cover. NOTE: After removing the belt cover, remove the cover mounting bracket from the left rear side of machine frame. 32 LEIL13WHL0154AB 33. Remove the drive belt from the engine. 33 LEIL13WHL0155AB 34. If machine is equipped with the air conditioning sys- tem, identify, tag, and disconnect the engine wiring harness connectors from air compressor clutch con- nector (1) and high pressure switch (2). Then remove the three mounting bolts (3) for the compressor and carefully set it on the left battery cover. 34 LEIL13WHL0156AB 35. Tag and disconnect the wiring from the alternator. 35 RAPH12WEL0622AA 47969425_EN 29/01/2016 10.1 [10.001] / 13

Engine - Engine and crankcase 36. Remove the return line of the SCR coolant. 36 RAPH12WEL0623AA 37. Tag and remove the wires from the starter solenoid (1), the ground cable (2), and ground strap (3) from the starter. NOTE: Move the starter cables away from the engine. 37 RAPH12WEL0624AA 38. Remove the bolts securing the wiring harness clamps to the engine. 38 RAPH12WEL0625AA 47969425_EN 29/01/2016 10.1 [10.001] / 14

Engine - Engine and crankcase 39. Remove the ground wires from the engine. NOTE: Move the wiring harness away from the engine. 39 RAPH12WEL0625AA 40. If the machine is so equipped, unplug the engine block heater and set it aside. 40 LEIL15WHL0016AB 41. Loosen the clamp (see the arrow in figure) and dis- connect the pipe. 41 LEIL15WHL0015AB 42. Loosen the clamps and remove the lower coolant hose from the engine. 42 RAPH12WEL0629AA 47969425_EN 29/01/2016 10.1 [10.001] / 15

Engine - Engine and crankcase 43. Remove the radiator hose from the engine. 43 LEIL13WHL0159AB 44. Remove the return radiator hose (1) and the engine coolant vent hose from the top of the radiator. 44 LEIL13WHL0141AB 45. Remove the overflow tank of the engine coolant. 45 RAPH12WEL0633AA 46. Remove the bracket of the overflow tank. 46 RAPH12WEL0634AA 47969425_EN 29/01/2016 10.1 [10.001] / 16

Engine - Engine and crankcase 47. Remove the cooling fan screen. 47 LEIL13WHL0160AB 48. Loosen the clamp (1) on the intake manifold for the output hose of the after cooler. Loosen the clamp (2) from the body of the DEF/ADBLUE tank vent filter. 48 LEIL13WHL0613AA 49. Loosen the clamp on the after cooler, and remove the output hose of the after cooler from the machine. 49 LEIL13WHL0162AB 50. Tag and disconnect the fuel filter heater wire (1) and the water sensor (2). Then drain fuel filter and discon- nect the inlet (3) and outlet (4) fuel lines from the fuel filter head. Plug the lines and cap the fittings. Remove the ground wire and the attachment bolt (5) of the fuel filter head. 50 LEIL13WHL0163AB 47969425_EN 29/01/2016 10.1 [10.001] / 17

Engine - Engine and crankcase 51. Tag and remove the grid heater cable (1). NOTE: Hold the rear nut with a second wrench to prevent grid heater damage. 51 LEIL13WHL0164AB 52. Remove wire harness support clamp. 52 RAPH12WEL0064AA 53. RemovetheP-clampandcutthecabletiesbythesup- ply module. Disconnect the end of the jumper harness (near the supply module) from the DOC support. 53 LEIL15WHL0034AB 54. Tag and disconnect the NOx controller harness (1), the NH3 sensor connector (4) and the temperature sensor connector (5) . Then remove the screws (2) and (3) of the clamp. 54 LEIL13WHL0165AB 47969425_EN 29/01/2016 10.1 [10.001] / 18

Engine - Engine and crankcase 55. Loosen the clamp (1) on the Diesel Oxidation Catalyst (DOC). 55 LEIL13WHL0166AB 56. Tag and disconnect the connector (1). 56 LEIL13WHL0167AB 57. Tag and disconnect the wire harness of the tempera- ture sensor (1) for the Selective Catalytic Reduction muffler (SCR) and cut the connector wire clamps. Loosen the screws and remove the bar (2). 57 LEIL14WHL0213AB 58. Attach a suitable lifting straps to the Selective Cat- alytic Reduction (SCR) muffler support structure. Re- move the bolts securing the support structure at the front (1) and rear (2) part of the structure. Use a suitable lifting device and carefully lift the support structure of the Selective Catalytic Reduction (SCR) muffler from the machine. NOTE: Pay particular attention to the connection between the(SCR)mufflerandtheDieselOxidationCatalyst(DOC). 58 LEIL13WHL0169AB 47969425_EN 29/01/2016 10.1 [10.001] / 19

Engine - Engine and crankcase 59. Tag and disconnect the wire harness from the buzzer. Remove the bolts (1) securing the front support struc- ture of the (SCR) muffler and remove it. 59 LEIL13WHL0174AB 60. Tag and disconnect wire harness from primary fuel filter. 60 RAPH12WEL0068AA 61. Remove DEF/ADBLUE storage tank cover located on the right hand side of the machine. 61 LEIL13WHL0170AB 62. Tag and disconnect the wire harness and DEF/ ADBLUE supply and DEF/ADBLUE storage tank. Cap the supply lines. return lines from the 62 RAPH12WEL0070AA 47969425_EN 29/01/2016 10.1 [10.001] / 20

Engine - Engine and crankcase 63. Remove the support bracket of the hood lift cylinder. 63 RAPH12WEL0071AA 64. Remove the heater hose from the engine. 64 LEIL15WHL0009AB 65. Disconnect the main connector of the supply module. 65 LEIL13WHL0171AB 66. Attach suitable lifting straps to the support structure (1) of the Diesel Oxidation Catalyst (DOC). The sup- ply module and the coolant control valve are also at- tached to this support structure. 66 LEIL14WHL0212AB 47969425_EN 29/01/2016 10.1 [10.001] / 21

Engine - Engine and crankcase 67. Loosen the two haxagonal nuts of the sensors (3) and (4) and disconnect the sensors (3) and (4). Loosen the clamp (1) on the Diesel Oxidation Catalyst (DOC) and disconnect the exhaust pipe (2) from the Diesel Oxidation Catalyst (DOC). 67 LEIL13WHL0229AA 68. Remove the SCR coolant supply line from the engine. 68 LEIL15WHL0008AB 69. Remove the bolts that secure the support structure of the Diesel Oxidation Catalyst (DOC). Use a suitable lifting device and carefully lift the sup- port structure of the Diesel Oxidation Catalyst (DOC) (withSCRsystemcomponentsattached)fromthema- chine. 69 LEIL13WHL0173AB 70. Disconnect the wiring harness from the EDC17 con- troller. NOTE: Lifting up on the lever will release the connector from the controller. 70 LEIL13WHL0175AB 47969425_EN 29/01/2016 10.1 [10.001] / 22

Engine - Engine and crankcase 71. Remove the fuel line from the top of the primary fuel filter, plug the line and cap the fitting. NOTE: Make note on how fuel lines are routed. 71 LEIL13WHL0176AB 72. Remove the support clamp of the fuel line. NOTE: Make note on how fuel lines are routed. 72 LEIL13WHL0177AB NOTE: make note on how fuel lines are routed, for reference during the reassembly. 73 LEIL15WHL0017FB 47969425_EN 29/01/2016 10.1 [10.001] / 23

Engine - Engine and crankcase 73. Remove the upper and lower covers for the drive shaft. 74 RAPH12WEL0079AA 74. Remove the drive shaft bolts (1) from the flywheel. Move the drive shaft clear of the flywheel. 75 RAPH12WEL0080AA 75. Connect and turn on vacuum pump to hydraulic reser- voir. Tag and remove the hydraulic lines from the brake system pump (arrow), plug the lines and cap the fittings. 76 LEIL13WHL0178AB 47969425_EN 29/01/2016 10.1 [10.001] / 24

Suggest: If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading

Engine - Engine and crankcase 76. Connect suitable lifting equipment to engine lifting brackets. Take up all slack in lifting equipment. Re- move the engine mounting bolts. 77 RAPH12WEL0080AA 78 LEIL15WHL0036AA 77. Slowly raise engine from rear chassis. Be sure all wire harness connections and hoses have been dis- connected and are clear of the engine. Guide the oil drain hose from the frame as the engine is lifted. Re- move engine from machine. 47969425_EN 29/01/2016 10.1 [10.001] / 25

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com