Caterpillar Cat 320D2 Excavator (Prefix WBF) Service Repair Manual Instant Download
Please open the website below to get the complete manualnn//
Download Presentation
Please find below an Image/Link to download the presentation.
The content on the website is provided AS IS for your information and personal use only. It may not be sold, licensed, or shared on other websites without obtaining consent from the author. Download presentation by click this link. If you encounter any issues during the download, it is possible that the publisher has removed the file from their server.
E N D
Presentation Transcript
Service Repair Manual Models 320D2 and320D2L Excavator
w 1/3(W) Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320D2 L EXCAVATOR WBF Configuration: 320D2 & 320D2 L Excavators WBF00001-UP (MACHINE) POWERED BY C7.1 Engine Disassembly and Assembly C7.1 (Mech) Engines for Caterpillar Built Machines Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017 i04780443 Flywheel - Remove SMCS - 1156-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty Guide Stud 1/2 inch - UNF by 4 inch A - 2 Start By: a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/1/9
w 2/3(W) Illustration 1 g01336668 Typical example 1. Remove bolts from Position (X) from flywheel (1). 2. Install Tooling (A) in Position (X) to flywheel (1). 3. Install a suitable lifting device onto flywheel (1). Support the weight of the flywheel. The flywheel can weigh 71 kg (156 lb). 4. If necessary, remove bolts (2) that secure the housing for pilot bearing (3) to flywheel (1). Remove the housing for pilot bearing (3). 5. Remove remaining bolts (4). 6. Use the lifting device to remove the flywheel from the engine. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/1/9
https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com
w 3/3(W) Illustration 2 g01336669 Typical example 7. Inspect flywheel (1) and ring gear (5) for wear and damage. Replace any worn components or damaged components. 8. To remove flywheel ring gear (5), follow Step 8.a through Step 8.b. a. Place the flywheel assembly on a suitable support. b. Use a hammer and a punch in order to remove ring gear (5) from flywheel (1). Note: Identify the orientation of the teeth on the flywheel ring gear. Copyright 1993 - 2020 Caterpillar Inc. Thu Jan 9 23:13:37 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/1/9
w 1/4(W) Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320D2 L EXCAVATOR WBF Configuration: 320D2 & 320D2 L Excavators WBF00001-UP (MACHINE) POWERED BY C7.1 Engine Disassembly and Assembly C7.1 (Mech) Engines for Caterpillar Built Machines Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017 i04780442 Flywheel - Install SMCS - 1156-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty Guide Stud 1/2 inch - UNF by 4 inch A - 2 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/1/9
w 2/4(W) Illustration 1 g01336671 Typical example Always wear protective gloves when handling parts that have been heated. 1. If the flywheel ring gear was removed, follow Step 1.a through Step 1.c in order to install ring gear (5) to flywheel (1). a. Identify the orientation of teeth (6) on new ring gear (5). Note: The chamfered side of ring gear teeth (6) must face toward the starting motor when the flywheel is installed. The chamfered side of ring gear teeth ensures the correct engagement of the starting motor. b. Heat flywheel ring gear (5) in an oven to a maximum temperature of 250 C (482 F) prior to installation. Note: Do not use a torch to heat the ring gear. c. Ensure that the orientation of ring gear (5) is correct and quickly install the ring gear onto flywheel (1). 2. Inspect the crankshaft rear seal for leaks. If there are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install" for the correct procedure. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/1/9
w 3/4(W) Illustration 2 g01336668 Typical example 3. Install a suitable lifting device onto flywheel (1). The flywheel can weigh 71 kg (156 lb). 4. Install Tooling (A) in Position (X) on the crankshaft. 5. Use the lifting device to position flywheel (1) onto Tooling (A). 6. If necessary, install pilot bearing (3) and bolts (2) to flywheel (1). 7. Install bolts (4) to flywheel (1). 8. Remove Tooling (A) and install remaining bolts (4) to flywheel (1). 9. Use a suitable tool to prevent the flywheel from rotating. Tighten bolts (2) and (4) to a torque of 140 N m (103 lb ft). 10. Remove the lifting device from flywheel (1). 11. Check the run out of the flywheel. Refer to Specifications, "Flywheel" for further information. End By: a. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/1/9
w 1/2(W) Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320D2 L EXCAVATOR WBF Configuration: 320D2 & 320D2 L Excavators WBF00001-UP (MACHINE) POWERED BY C7.1 Engine Disassembly and Assembly C7.1 (Mech) Engines for Caterpillar Built Machines Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017 i04780405 Crankshaft Rear Seal - Remove SMCS - 1161-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 227-4389 E10 Torx Socket 1 Start By: a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/1/9
w 2/2(W) Dispose of all fluids according to local regulations and mandates. Note: The crankshaft rear seal and the housing are manufactured as a one-piece assembly. The assembly is not serviceable. If the crankshaft rear seal is removed, the assembly must be replaced. Illustration 1 g02711971 1. Use Tooling (A) in order to remove torx screws (1) from crankshaft rear seal (2). 2. Remove crankshaft rear seal (2) from the cylinder block. Discard the crankshaft rear seal. Copyright 1993 - 2020 Caterpillar Inc. Thu Jan 9 23:15:29 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/1/9
w 1/4(W) Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320D2 L EXCAVATOR WBF Configuration: 320D2 & 320D2 L Excavators WBF00001-UP (MACHINE) POWERED BY C7.1 Engine Disassembly and Assembly C7.1 (Mech) Engines for Caterpillar Built Machines Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017 i04780403 Crankshaft Rear Seal - Install SMCS - 1161-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 227-4389 E10 Torx Socket 1 B FT-2806 Alignment Tool 1 Note: The crankshaft rear seal and the housing are manufactured as a one-piece assembly. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/1/9
w 2/4(W) Illustration 1 g02717043 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/1/9
w 3/4(W) Illustration 2 g02717045 1. Ensure that crankshaft flange (1) is clean, dry, and free from damage. 2. Ensure that the face of the cylinder block and the bridge piece are clean and dry. 3. A new crankshaft rear seal is supplied with a plastic sleeve (3). Ensure that the plastic sleeve is squarely installed within crankshaft rear seal (2). Note: The plastic sleeve is included in order to protect the lip of the seal as the seal is pushed over the crankshaft flange. Note: Do not lubricate the crankshaft rear seal or the crankshaft flange. The crankshaft rear seal must be installed dry. 4. Align plastic sleeve (3) with crankshaft flange (1). Ensure that the plastic sleeve is engaged onto the crankshaft flange. Push new crankshaft rear seal (2) squarely onto the crankshaft flange. During this process, the plastic sleeve will be forced out of the crankshaft rear seal. Discard the plastic sleeve. 5. Ensure that crankshaft rear seal (2) is seated against the cylinder block. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/1/9
w 4/4(W) Illustration 3 g02717046 6. Install torx screws (4) finger tight. Note: Do not install torx screws to Positions (X) at this stage. 7. Install Tooling (B) to crankshaft rear seal (2) and to crankshaft flange (1). Use Tooling (B) to align crankshaft rear seal (2) with crankshaft flange (1). 8. Use Tooling (A) in order to tighten torx screws (4) to a torque of 22 N m (195 lb in). Tighten torx screws (4) in the sequence that is shown in Illustration 3. 9. Remove Tooling (B). 10. Install remaining torx screws (4) to Positions (X). Use Tooling (A) in order to tighten the torx screws to a torque of 22 N m (195 lb in). Refer to Illustration 3. End By: a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install". Copyright 1993 - 2020 Caterpillar Inc. Thu Jan 9 23:16:25 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/1/9
w 1/7(W) Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320D2 L EXCAVATOR WBF Configuration: 320D2 & 320D2 L Excavators WBF00001-UP (MACHINE) POWERED BY C7.1 Engine Disassembly and Assembly C7.1 (Mech) Engines for Caterpillar Built Machines Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017 i04780445 Flywheel Housing - Remove and Install - Standard Housing SMCS - 1157-010 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty Guide Stud M10 by 100 mm A - 2 Start By: a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove" for the correct procedure. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/1/9
w 2/7(W) Illustration 1 g02227473 Typical example https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/1/9
w 3/7(W) Illustration 2 g02227474 Typical example 1. Remove bolts (3) from Position (X) from flywheel housing (1). 2. Install Tooling (A) into Position (X) on flywheel housing (1). 3. Install a suitable lifting device onto the flywheel housing in order to support the flywheel housing. The weight of the flywheel housing is approximately 40 kg (88 lb). 4. Remove bolts (2) and remaining bolts (3) from flywheel housing (1). 5. Use a suitable lifting device in order to remove flywheel housing (1) from the cylinder block. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/1/9
w 4/7(W) Illustration 3 g01983533 Typical example 6. Remove dust seal (5). 7. If necessary, remove dowels (4) from the cylinder block. Installation Procedure (Standard Housing) Table 2 Required Tools Tool Part Number Part Description Qty Guide Stud M10 by 100 mm A - 2 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/1/9
w 5/7(W) 1. Ensure that the flywheel housing is clean and free from damage. If necessary, replace the flywheel housing. Illustration 4 g01983535 Typical example 2. Inspect crankshaft rear seal (6) for leaks. If there are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" and refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install" for the correct procedure. 3. Clean the rear face of the cylinder block. If necessary, install dowels (4) to the cylinder block. 4. Install Tooling (A) to the cylinder block. 5. Install dust seal (5). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/1/9
w 6/7(W) Illustration 5 g02227475 Typical example 6. Install a suitable lifting device onto the flywheel housing. The weight of the flywheel housing is approximately 40 kg (88 lb). 7. Use the lifting device to align flywheel housing (1) with Tooling (A). Install the flywheel housing to the cylinder block. 8. Install bolts (2) and bolts (3). 9. Remove Tooling (A). Install remaining bolts (3). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/1/9
w 7/7(W) Illustration 6 g01984554 Identification of the bolt Grade. 10. When 8.8 Graded bolts are installed, follow Step 10.a through Step 10.b. a. Tighten bolts (3) to a torque of 63 N m (46 lb ft). b. Tighten bolts (2) to a torque of 78 N m (58 lb ft). 11. When 10.9 Graded bolts are installed follow Step 11.a through Step 11.b. a. Tighten bolts (3) to a torque of 115 N m (85 lb ft). b. Tighten bolts (2) to a torque of 190 N m (140 lb ft). 12. Check the alignment of flywheel housing (1) with the crankshaft. Refer to System Operation, Testing and Adjusting, "Flywheel Housing - Inspect" for more information. End By: a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install" for the correct procedure. Copyright 1993 - 2020 Caterpillar Inc. Thu Jan 9 23:17:21 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/1/9
Suggest: If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading
w 1/3(W) Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320D2 L EXCAVATOR WBF Configuration: 320D2 & 320D2 L Excavators WBF00001-UP (MACHINE) POWERED BY C7.1 Engine Disassembly and Assembly C7.1 (Mech) Engines for Caterpillar Built Machines Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017 i05909468 Vibration Damper and Pulley - Remove SMCS - 1205-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty Guide Stud M14 x 1.5 by 100 mm A - 1 B 227-4393 E18 Torx Socket 1 Start By: A. Remove the alternator belt. Refer to Disassembly and Assembly, "V- Belts - Remove and Install" for the correct procedure. Note: The weight of the assembly of the crankshaft pulley, the vibration damper, and the crankshaft adapter is approximately 22 kg (48 lb). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/1/9
https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com
