Bobcat S510 Skid Steer Loader Service Repair Manual Instant Download (SN ALNW11001 and Above, SN B42S11001 and Above)

MAINTENANCE SAFETY Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Operator s Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow instructions can cause injury or death. WARNING W-2003-0807 Safety Alert Symbol: This symbol with a warning statement, means: Warning, be alert! Your safety is involved! Carefully read the message that follows. CORRECT CORRECT CORRECT P-90216 NA1204 NA1193 Cleaning and maintenance are required daily. Never service the Bobcat Skid- Steer Loader without instructions. Use the correct procedure to lift or lower operator cab. WRONG WRONG WRONG NA1192 NA1205 NA1206 Have good ventilation when welding or grinding painted parts. Wear dust mask when grinding painted parts. Toxic dust and gas can be produced. Avoid exhaust fume leaks which can kill without warning. Exhaust system must be tightly sealed. Disconnecting or loosening any hydraulic tubeline, hose, fitting, component or a part failure can cause lift arms to drop. Do not go under lift arms when raised unless supported approved lift arm support device. Replace it if damaged. Never work on loader with lift arms up unless lift arms are held by an approved lift arm support device. Replace if damaged. Never modify equipment or add attachments not approved by Bobcat Company. by an WRONG WRONG WRONG NA1191 B-6589 NA1200 Stop, cool and clean engine of flammable materials checking fluids. Never service or adjust loader with the engine running unless instructed to do so in the manual. Avoid contact hydraulic fluid or diesel fuel under pressure. It can penetrate the skin or eyes. Never fill fuel tank with engine running, while smoking or when near open flame. Maintenance procedures which are given in the Operation & Maintenance Manual can be performed by the owner/ operator without any specific technical training. Maintenance procedures which are not in the Operation & Maintenance Manual must be performed ONLY BY QUALIFIED BOBCAT SERVICE PERSONNEL. Always use genuine Bobcat replacement parts. The Service Safety Training Course is available from your Bobcat dealer. Keep body, jewelry and clothing away from moving electrical contact, hot parts and exhaust. Wear eye protection to guard from battery acid, compressed springs, fluids under pressure and flying debris when engines are running or tools are used. Use eye protection approved for type of welding. Keep rear door closed except for service. Close and latch door before operating the loader. Lead-acid flammable and explosive gases. Keep arcs, sparks, flames and lighted tobacco batteries. Batteries contain acid which burns eyes or skin on contact. Wear protective clothing. If acid contacts body, flush well with water. For eye contact flush well and get immediate attention. batteries produce before parts, away from with leaking medical MSW35-0409 1-1 S510 Service Manual

CONTENTS SAFETY AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-01 HYDRAULIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-01 HYDROSTATIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-01 DRIVE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-01 MAINFRAME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-01 ELECTRICAL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60-01 ENGINE SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70-01 HEATING AND VENTILATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80-01 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPEC-01 ALPHABETICAL INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .INDEX-01 1-3 S510 Service Manual

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com

FOREWORD FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7 SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9 FIRE PREVENTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11 Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11 Hydraulic System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11 Fueling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11 Spark Arrester Exhaust System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11 Welding And Grinding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12 Fire Extinguishers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12 SERIAL NUMBER LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13 Loader Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13 Engine Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13 DELIVERY REPORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14 LOADER IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15 1-5 S510 Service Manual

SAFETY FOREWORD This manual is for the Bobcat loader mechanic. It provides necessary servicing and adjustment procedures for the Bobcat loader and its component parts and systems. Refer to the Operation & Maintenance Manual for operating instructions, starting procedure, daily checks, etc. A general inspection of the following items must be made after the loader has had service or repair: 1. Check that the ROPS/FOPS (Including side screens) is in good condition and is not modified. 9. The parking brake must function correctly. 2. Check that ROPS mounting hardware is tightened and is Bobcat approved. 10. Enclosure door latches must open and close freely. 3. The seat belt must be correctly installed, functional and in good condition. 11. Bob-Tach linkages correctly and be in good condition. wedges must and function 4. The correctly adjusted, clean and lubricated. seat bar must be 12. Safety treads must be in good condition. SERVICE 5. Check lift arm support device, replace if damaged. 13. Check for correct function of indicator lamps. 6. Machine signs (decals) must be legible and in the correct location. 14. Check levels. all machine fluid 7. Steering levers, hand controls and foot pedals must return to neutral (as applicable). 15. Inspect hydraulic fluid leaks. for fuel, oil or 8. Check for correct function of the work lights. 16. Lubricate the loader. FW SSL-0617 SM 1-7 S510 Service Manual

17. Check the condition of the battery and cables. 23. Operate the machine and check all functions. 18. Inspect the air cleaner for damage or leaks. Check the condition of the element. 24. Check for correct function of the Bobcat Interlock Control System (BICS ) before the machine is returned to the customer. 25. Check for proper function of front horn and back-up alarm (if equipped). 19. Check the electrical charging system. 20. Check tires for wear and pressure. Check tracks for wear and tension. Use only approved tires or tracks. 26. Check function or condition of all equipped options and accessories (examples: fire extinguisher, rotating beacon, lift kits, etc.). 27. Recommend to the owner that all necessary corrections be made before the machine is returned to service. 21. Inspect for loose or broken parts or connections. 22. Check modification not completed. for any field CALIFORNIA PROPOSITION 65 WARNING Diesel engine exhaust and some of its constituents are known to the state of California to cause cancer, birth defects and other reproductive harm. FW SSL-0617 SM 1-8 S510 Service Manual

SAFETY INSTRUCTIONS The following publications provide information on the safe use and maintenance of the Bobcat machine and attachments: Safety Alert Symbol The Delivery Report is used to assure that complete instructions have been given to the new owner and that the machine is in safe operating condition. This symbol with a warning statement means: Warning, be alert! Your safety is involved! Carefully read the message that follows. The Operation & Maintenance Manual delivered with the machine or attachment contains operating information as well as routine maintenance and service procedures. It is a part of the machine and can be stored in a container provided on the machine. Replacement Operation & Maintenance Manuals can be ordered from your Bobcat dealer. WARNING AVOID INJ URY OR DEATH Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow instructions can cause injury or death. Machine signs (decals) instruct on the safe operation and care of your Bobcat machine or attachment. The signs and their locations are shown in the Operation & Maintenance Manual. Replacement signs are available from your Bobcat dealer. Manual, Operator s An Operator s Handbook fastened to the operator cab. It s brief instructions are convenient to the operator. The handbook is available from your dealer in an English edition or one of many other languages. See your Bobcat dealer for more information on translated versions. W-2003-0807 IMPORTANT The AEM Safety Manual delivered with the machine gives general safety information. This notice identifies procedures which must be followed to avoid damage to the machine. The Service Manual and Parts Manual are available from your dealer for use by mechanics to do shop- type service and repair work. I-2019-0284 The Skid-Steer Loader Operator Training Course is available through your local dealer or at Bobcat.com/ training or Bobcat.com. This course is intended to provide rules and practices of correct operation of the skid-steer loader. The course is available in English and Spanish versions. DANGER The signal word DANGER on the machine and in the manuals indicates a hazardous situation which, if not avoided, will result in death or serious injury. Service Safety Training Courses are available from your Bobcat dealer or at Bobcat.com/training or Bobcat.com. They provide information for safe and correct service procedures. D-1002-1107 The Skid-Steer Loader Safety Video is available from your Bobcat dealer or at Bobcat.com/training or Bobcat.com. WARNING The signal word WARNING on the machine and in the manuals indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. W-2044-1107 SI SSL-1016 SM 1-9 S510 Service Manual

FIRE PREVENTION Hydraulic System Check hydraulic tubes, hoses and fittings for damage and leakage. Never use open flame or bare skin to check for leaks. Hydraulic tubes and hoses must be properly routed and have adequate support and secure clamps. Tighten or replace any parts that show leakage. Maintenance Always clean fluid spills. Do not use gasoline or diesel fuel for cleaning parts. Use commercial nonflammable solvents. The machine and some attachments have components that are at high temperatures under normal operating conditions. The primary source of high temperatures is the engine and exhaust system. The electrical system, if damaged or incorrectly maintained, can be a source of arcs or sparks. Fueling Flammable debris (leaves, straw, etc.) must be removed regularly. If flammable debris is allowed to accumulate, it can cause a fire hazard. Clean often to avoid this accumulation. Flammable compartment is a potential fire hazard. debris in the engine Stop the engine and let it cool before adding fuel. No smoking! Do not refuel a machine near open flames or sparks. Fill the fuel tank outdoors. The operator s area, engine compartment and engine cooling system must be inspected every day and cleaned if necessary to prevent fire hazards and overheating. Ultra Low Sulfur Diesel (ULSD) poses a greater static ignition hazard than earlier diesel formulations with higher Sulfur content. Avoid death or serious injury from fire or explosion. Consult with your fuel or fuel system supplier to ensure the delivery system is in compliance with fueling standards for proper grounding and bonding practices. All fuels, most lubricants and some coolants mixtures are flammable. Flammable fluids that are leaking or spilled onto hot surfaces or onto electrical components can cause a fire. Operation Starting Do not use the machine where exhaust, arcs, sparks or hot components can contact flammable material, explosive dust or gases. Do not use ether or starting fluids on any engine that has glow plugs or air intake heater. These starting aids can cause explosion and injure you or bystanders. Electrical Use the procedure in the Operation & Maintenance Manual for connecting the battery and for jump starting. Spark Arrester Exhaust System The spark arrester exhaust system is designed to control the emission of hot particles from the engine and exhaust system, but the muffler and the exhaust gases are still hot. Check all electrical wiring and connections for damage. Keep the battery terminals clean and tight. Repair or replace any damaged part or wires that are loose or frayed. Check the spark arrester exhaust system regularly to make sure it is maintained and working properly. Use the procedure in the Operation & Maintenance Manual for cleaning the spark arrester muffler (if equipped). Battery gas can explode and cause serious injury. Use the procedure in the Operation & Maintenance Manual for connecting the battery and for jump starting. Do not jump start or charge a frozen or damaged battery. Keep any open flames or sparks away from batteries. Do not smoke in battery charging area. SI SSL-1016 SM 1-11 S510 Service Manual

FIRE PREVENTION (CONTD) Welding And Grinding Always clean the machine and attachment, disconnect the battery, and disconnect the wiring from the Bobcat controllers before welding. Cover rubber hoses, battery and all other flammable parts. Keep a fire extinguisher near the machine when welding. Have good ventilation when grinding or welding painted parts. Wear dust mask when grinding painted parts. Toxic dust or gas can be produced. Dust generated from repairing nonmetallic parts such as hoods, fenders or covers can be flammable or explosive. Repair such components in a well ventilated area away from open flames or sparks. Fire Extinguishers Know where fire extinguishers and first aid kits are located and how to use them. Inspect the fire extinguisher and service the fire extinguisher regularly. Obey the recommendations on the instructions plate. SI SSL-1016 SM 1-12 S510 Service Manual

SERIAL NUMBER LOCATIONS Always use the serial number of the loader when requesting service information or when ordering parts. Earlier or later models (identification made by serial number) may use different parts, or there may be different procedures to follow when performing a specific service operation. Loader Serial Number Engine Serial Number Figure 1 Figure 3 1 1 P109031F P109660 The loader serial number plate (Item 1) [Figure 1] is located on the outside of the loader frame. The engine serial number (Item 1) [Figure 3] is located on the side of the engine next to the oil fill cap. Figure 2 Module 2 Production Sequence (Series) Module 1 Model / Engine Combination NA3095 Explanation of loader Serial Number [Figure 2]: 1. The four digit Model / Engine Combination Module number identifies the model number and engine combination. 2. The five digit Production Sequence Number identifies the order in which the loader is produced. 1-13 S510 Service Manual

DELIVERY REPORT Figure 4 NA3106 The delivery report [Figure 4] contains a list of items that must be explained or shown to the owner or operator by the dealer when the Bobcat loader is delivered. The delivery report must be reviewed and signed by the owner or operator and the dealer. 1-14 S510 Service Manual

LOADER IDENTIFICATION 2 1 20 11 3 12 19 4 5 18 13 10 14 6 9 7 8 15 16 17 NA5798 NA5799 ITEM DESCRIPTION ITEM DESCRIPTION Operation & Maintenance Manual and Operator s Handbook Front Lights Grab Handles Operator Seat with Seat Belt and Seat Bar Tilt Cylinders Lift Cylinder (Both Sides) 1 11 Rear Grille Back-up Alarm Rear Work Lights and Taillights Rear Door Rear Tie-down (Both Sides) Front Tie-down located behind Bucket Tires [C] Lift Arm Support Device Lift Arm Operator Cab (ROPS and FOPS) [B] 2 3 4 5 12 13 14 15 Bucket [A] 6 16 Bucket Steps Step Alternate Front Tie-down (Both Sides) Front Auxiliary Quick Couplers 7 8 9 10 17 18 19 20 [A] Bucket Several different buckets and other attachments are available for the Bobcat loader. [B] ROPS Roll-Over Protective Structure per ISO 3471 and FOPS Falling-Object Protective Structure per ISO 3449, Level I. Level II is available. [C] Tires Standard tires are shown. Several different tire styles and sizes are available for the Bobcat loader. 1-15 S510 Service Manual

SAFETY AND MAINTENANCE LIFTING AND BLOCKING THE LOADER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10-1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10-1 LIFT ARM SUPPORT DEVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-20-1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-20-1 Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-20-2 Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-20-3 OPERATOR CAB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-30-1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-30-1 Cab Door Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-30-1 Raising . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-30-2 Lowering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-30-3 Special Applications Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-30-4 Special Applications Kit Inspection And Maintenance . . . . . . . . . . . . . . . . . . . . . . . 10-30-4 Forestry Door And Window Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-30-5 Forestry Door And Window Kit Inspection And Maintenance . . . . . . . . . . . . . . . . . . 10-30-5 TRANSPORTING THE LOADER ON A TRAILER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-40-1 Loading And Unloading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-40-1 Fastening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-40-1 TOWING THE LOADER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-50-1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-50-1 REMOTE START TOOL KIT- MEL1563 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-60-1 Remote Start Tool - MEL1563 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-60-1 Service Tool Harness Communicator - MEL1566 . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-60-3 Remote Start Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-60-3 REMOTE START TOOL (SERVICE TOOL) KIT - 7217666 . . . . . . . . . . . . . . . . . . . . . . 10-61-1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-61-1 Remote Start Tool (Service Tool) - 7022042 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-61-2 Loader Service Tool Harness - 6689747 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-61-3 Computer Service Tool Harness - 6689746 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-61-4 Remote Start Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-61-5 SERVICE SCHEDULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-70-1 Maintenance Intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-70-1 ENGINE AIR CLEANER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-80-1 Replacing Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-80-1 ENGINE COOLING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-90-1 Maintenance Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-90-1 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-90-1 Checking And Adding Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-90-3 Removing And Replacing Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-90-4 10-01 S510 Service Manual

FUEL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-100-1 Fuel Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-100-1 Biodiesel Blend Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-100-1 Filling The Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-100-2 Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-100-3 Removing Air From The Fuel System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-100-5 ENGINE LUBRICATION SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-110-1 Checking And Adding Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-110-1 Engine Oil Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-110-1 Removing And Replacing Oil And Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-110-2 HYDRAULIC / HYDROSTATIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-120-1 Checking And Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-120-1 Hydraulic / Hydrostatic Fluid Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-120-1 Removing And Replacing Hydraulic Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-120-2 Removing And Replacing Hydraulic / Hydrostatic Filter . . . . . . . . . . . . . . . . . . . . . 10-120-4 Removing And Replacing Hydraulic Charge Filter . . . . . . . . . . . . . . . . . . . . . . . . . 10-120-5 Replacing Reservoir Breather Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-120-7 FINAL DRIVE TRANSMISSION (CHAINCASE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-130-1 Checking And Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-130-1 Removing And Replacing Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-130-1 BOB-TACH (HAND LEVER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-140-1 Inspection And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-140-1 BOB-TACH (POWER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-141-1 Inspection And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-141-1 LUBRICATING THE LOADER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-150-1 Lubrication Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-150-1 TIRE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-160-1 Wheel Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-160-1 Rotating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-160-1 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-160-2 PIVOT PINS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-170-1 Inspection And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-170-1 LOADER STORAGE AND RETURN TO SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-180-1 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-180-1 Return To Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-180-1 STOPPING THE ENGINE AND LEAVING THE LOADER . . . . . . . . . . . . . . . . . . . . . . 10-190-1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-190-1 10-02 S510 Service Manual

EMERGENCY EXIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-200-1 Rear Window Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-200-1 Rear Window Removal (Latches) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-200-1 Rear Window Removal (Rubber Cord) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-200-1 External Access (Rear Window With Latches) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-200-2 External Access (Rear Window With Rubber Cord) . . . . . . . . . . . . . . . . . . . . . . . . 10-200-2 Front Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-200-2 SEAT BELT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-210-1 Inspection And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-210-1 10-03 S510 Service Manual

LIFTING AND BLOCKING THE LOADER Figure 10-10-2 Procedure Figure 10-10-1 P-90556 P-85425 Lift the rear of the loader and install jackstands in the notched area of the frame [Figure 10-10-2]. B-7023A Figure 10-10-3 WARNING AVOID INJURY OR DEATH Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow instructions can cause injury or death. Manual, Operator s P-85985 W-2003-0807 Read the Removal And Installation, Disassembly And Assembly, etc. completely to become familiar with the procedure before beginning [Figure 10-10-1]. Lift the front of the loader and install jackstands under the axle tubes [Figure 10-10-3]. NOTE: Make sure the jackstands do not touch the tires. Make sure the tires clear the floor or any obstacles. Always park the loader on a level surface. WARNING NOTE: The lift arms are raised for photo clarity. MACHINE FALLING OR MOVING CAN CAUSE SERIOUS INJURY OR DEATH Put jackstands under the front and rear of the machine before running engine for service. W-2718-0208 10-10-1 S510 Service Manual

LIFT ARM SUPPORT DEVICE Description WARNING Never work on a machine with the lift arms up unless the lift arms are secured by an approved lift arm support device. Failure to use an approved lift arm support device can allow the lift arms or attachment to fall and cause injury or death. Service lift arm support device if damaged or if parts are missing. Using a damaged lift arm support or with missing parts can cause lift arms to drop causing injury or death. W-2572-0407 Figure 10-20-1 1 2 P109033 The lift arm support device (Item 1) [Figure 10-20-1] is used to support the lift arms while working on a machine with the lift arms up. A decal (Item 2) [Figure 10-20-1] located on the right side of the operator cab provides instructions for installing and removing the lift arm support device. The procedures are described in more detail on the following pages. (See Installing on Page 10-20-2.) and (See Removing on Page 10-20-3.) 10-20-1 S510 Service Manual

LIFT ARM SUPPORT DEVICE (CONTD) Figure 10-20-3 Installing DANGER 1 P109014 P-90328 AVOID DEATH Lower the lift arm support device to the top of the lift cylinder. Hook the free end of the spring (Item 1) [Figure 10-20-3] to the lift arm support device to prevent interference with lift arm support device engagement. Disconnecting or loosening any hydraulic tubeline, hose, fitting, component or a part failure can cause lift arms to drop. Keep out of this area when lift arms are raised unless supported by an approved lift arm support. Replace if damaged. Sit in the operator s seat, fasten the seat belt, and lower the seat bar. Start the engine. D-1009-0409 Figure 10-20-4 Remove attachment from the loader. Figure 10-20-2 2 2 1 1 3 P109015A P109016A Raise the lift arms until the lift arm support device drops onto the lift cylinder rod (Item 1) [Figure 10-20-4]. P107247A P109013 Lower the lift arms slowly until the lift arm support device is held between the lift arms and the lift cylinder. Put jackstands under the rear corners of the loader frame (Inset) [Figure 10-20-2]. Stop the engine, raise the seat bar, unbuckle the seat belt, and make sure lift and tilt functions are deactivated. Disconnect the spring (Item 3) from the lift arm support device retaining pin (Item 2). Support the lift arm support device (Item 1) [Figure 10-20-2] with your hand and remove the retaining pin. Install the retaining pin (Item 2) [Figure 10-20-4] into the rear of the lift arm support device below the lift cylinder rod. 10-20-2 S510 Service Manual

Suggest: If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading

LIFT ARM SUPPORT DEVICE (CONTD) Figure 10-20-6 Removing DANGER P109012 P-90328 AVOID DEATH Raise the lift arms a small amount. The spring will lift the lift arm support device off the lift cylinder rod [Figure 10- 20-6]. Fully lower the lift arms. Disconnecting or loosening any hydraulic tubeline, hose, fitting, component or a part failure can cause lift arms to drop. Keep out of this area when lift arms are raised unless supported by an approved lift arm support. Replace if damaged. Stop the engine, raise the seat bar, unbuckle the seat belt, and make sure lift and tilt functions are deactivated. D-1009-0409 Disconnect the spring from the bracket. Figure 10-20-5 Figure 10-20-7 1 1 2 2 3 P109017 P109013 Remove the retaining pin (Item 3) [Figure 10-20-5] from the lift arm support device. Raise the lift arm support device into the storage position and insert the retaining pin (Item 1) through the lift arm support device and the bracket. Hook the spring (Item 2) [Figure 10-20-7] to the retaining pin. Connect the spring (Item 1) from the lift arm support device to the bracket (Item 2) [Figure 10-20-5] on the bottom of the lift arm. Remove the jackstands. Sit in the operator s seat, fasten the seat belt, and lower the seat bar. Start the engine. 10-20-3 S510 Service Manual

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com