BOBCAT 753 LOADER Service Repair Manual Instant Download

? Service Manual ? ? Melroe Company 1990 6720326 (8 90) Printed in U.S.A.

MAINTENANCE SAFETY Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Operator s Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow instructions can cause injury or death. WARNING W-2003-0903 Safety Alert Symbol: This symbol with a warning statement, means: Warning, be alert! Your safety is involved! Carefully read the message that follows. CORRECT CORRECT CORRECT B-10731a B-12365 B-7469 Never service the Bobcat Skid- Steer Loader without instructions. Use the correct procedure to lift or lower operator cab. Cleaning and maintenance are required daily. WRONG WRONG WRONG B-11799 B-15231 B-15280 Have good ventilation when welding or grinding painted parts. Wear dust mask when grinding painted parts. Toxic dust and gas can be produced. Avoid exhaust fume leaks which can kill without warning. Exhaust system must be tightly sealed. Disconnecting or loosening any hydraulic tubeline, hose, fitting, component or a part failure can cause lift arms to drop. Do not go under lift arms when raised unless supported approved lift arm support device. Replace it if damaged. Never work on loader with lift arms up unless lift arms are held by an approved lift arm support device. Replace if damaged. Never modify equipment or add attachments not approved by Bobcat Company. by an WRONG WRONG WRONG B-6580 B-6589 B-6590 B-16102 B-16102 Stop, cool and clean engine of flammable materials checking fluids. Never service or adjust loader with the engine running unless instructed to do so in the manual. Avoid contact hydraulic fluid or diesel fuel under pressure. It can penetrate the skin or eyes. Never fill fuel tank with engine running, while smoking or when near open flame. Maintenance procedures which are given in the Operation & Maintenance Manual can be performed by the owner/ operator without any specific technical training. Maintenance procedures which are not in the Operation & Maintenance Manual must be performed ONLY BY QUALIFIED BOBCAT SERVICE PERSONNEL. Always use genuine Bobcat replacement parts. The Service Safety Training Course is available from your Bobcat dealer. Keep body, jewelry and clothing away from electrical contact, hot parts and exhaust. Wear eye protection to guard from battery acid, compressed springs, fluids under pressure and flying debris when engines are running or tools are used. Use eye protection approved for type of welding. Keep rear door closed except for service. Close and latch door before operating the loader. Lead-acid flammable and explosive gases. Keep arcs, sparks, flames and lighted tobacco batteries. Batteries contain acid which burns eyes or skin on contact. Wear protective clothing. If acid contacts body, flush well with water. For eye contact flush well and get immediate attention. batteries produce before moving parts, away from with leaking medical MSW01-0805

FOREWORD This manual is for the Bobcat loader mechanic. It provides necessary servicing and adjustment procedures for the Bobcat loader and its component parts and systems. Refer to the Operation & Maintenance Manual for operating instructions, starting procedure, daily checks, etc. A general inspection of the following items must be made after the loader has had service or repair: 1. Check that the ROPS/FOPS (Including sidescreens) is in good condition and is not modified. 9. Enclosure door latches must open and close freely. 2. Check that ROPS mounting hardware is tightened and is Melroe approved. 10. Bob Tach wedges and linkages must function correctly and be in good condition. 3. The seat belt must be correctly installed, functional and in good condition. 11. Safety treads must in good condition. 4. The seat bar and pedal interlocks must be correctly adjusted, clean and lubricated. 12. Check for correct function of indicator lamps (Optional on some models). 5. Machine signs must be legible and in the correct location. 13. Check hydraulic fluid level, engine oil level and fuel supply. 6. Steering levers and foot pedals must return to neutral. 14. Inspect for fuel, oil or hydraulic fluid leaks. 7. Check for correct function of the work lights and travel lights. 15. Lubricate the loader. 8. The parking brake must function correctly. 16. Check the condition of the battery and cables. 750 Series Loader Service Manual Revised Dec. 92 3

17. Inspect the air cleaner for damage or leaks. Check the condition of the element. 18. Check the electrical charging system. 19. Check tires for wear and pressure. 20. Inspect for loose or broken parts or connections. 21. Operate the loader and check all functions. 22. Check for any field modification not completed. Recommend to the owner that all necessary corrections be made before the machine is returned to service. 750 Series Loader Service Manual Revised Dec. 92 2

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com

CONTENTS PREVENTIVE MAINTENANCE SAFETY INSTRUCTIONS SERIAL NUMBER LOCATIONS DELIVERY REPORT BOBCAT LOADER IDENTIFICATION PREVENTIVE MAINTENANCE HYDRAULIC SYSTEM HYDROSTATIC SYSTEM DRIVE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MAIN FRAME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ELECTRICAL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ENGINE SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i ii iii iii HYDRAULIC SYSTEM 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 HYDROSTATIC SYSTEM DRIVE SYSTEM MAIN FRAME ELECTRICAL SYSTEM ENGINE SERVICE SPECIFICATIONS 750 Series Loader Service Manual 1

Both new and rebuilt starters are available from Melroe. Available at your local Bobcat Dealer. 750 Series Loader Service Manual 0

SAFETY INSTRUCTIONS Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow instructions can cause injury or death. W 2003 0299 The following publications provide information on the safe use and maintenance of the loader and attachments: 1. The Delivery Report is used to assure that complete instructions have been given to the new owner and that the machine is in safe operating condition. 2. The Operation & Maintenance Manual delivered with the loader gives operating information as well as routine maintenance and service procedures. It is a part of the loader and must stay with the machine when it is sold. 3. The loader has machine signs (decals) which instruct on the safe care and operation. The signs and their locations are shown in the Operation & Maintenance Manual. Replacement signs are available from your Bobcat loader dealers. 4. The FIEI Manual delivered with the loader gives general safety information. 5. The Service Manual and Parts Manual are available from Bobcat loader dealers for use by mechanics to do shop type service and repair work. Warnings on the machine and in the manuals are for your safety. Failure to obey warnings can cause injury or death. This notice identifies procedures which must be followed to avoid damage to the machine. I 2019 0284 W 2044 1285 Safety Alert Symbol: This Safety Symbol is used for important safety messages. When you see this symbol follow the safety message to avoid personal injury. Wear tight fitting clothing and any other required safety apparel when operating or servicing the loader. Wear safety glasses when maintaining or servicing the loader. Exhaust gases can kill, vent engine exhaust outdoors. Know where fire extinguishers and first aid kits are located and how to use them. Do not run the Bobcat loader where exhaust, arcs, sparks or hot components can contact flammable material, explosive dust or gases. Check fuel and hydraulic tubes, hoses and fittings for damage and leakage. Never use open flame or bare skin to check for leaks. Tighten or replace any parts that show leakage. Always clean fluid spills. DO NOT use gasoline or diesel fuel for cleaning parts. Use commercial nonflammable solvents. Clean the loader before doing any welding. Cover rubber hoses, battery and all other flammable parts. Keep a fire extinguisher near the loader when welding. Have good ventilation when welding or grinding painted parts. Wear a dust mask when grinding painted parts. Toxic dust or gas can be produced. Stop the engine and let it cool before adding fuel. No smoking! Use the procedure in this manual for connecting battery. Use the procedure in this manual for cleaning the spark arrestor muffler after each 100 hours of operation. 750 Series Loader Service Manual i

SERIAL NUMBER LOCATIONS A Always use the serial number of the loader when requesting service information or when ordering parts. Early or later models (identification made by serial number) may use different parts, or it may be necessary to use a different procedure in doing a specific service operation. LOADER SERIAL NUMBER The loader serial number plate is located on the inside of the left upright, above the grill [A]. Explanation of loader Serial Number: XXXXX XXXX CD 06862 Production Sequence (Series) B Model, Engine Version ENGINE SERIAL NUMBER LOCATION The serial number is near the fuel injection pump on the engine block [B]. CD 06863 C DELIVERY REPORT The Delivery Report must be filled out by the dealer and signed by the owner or operator when the Bobcat loader is delivered. An explanation of the form must be given to the owner. Make sure it is filled out completely [C]. 750 Series Loader Service Manual ii

V. BOBCAT LOADER IDENTIFICATION 843, 843B Service Manual #6566091 Contents Section FRONT LIGHTS OPERATOR SEAT GRAB HANDLES STEERNG LEVER REAR AUXILIARY QUICK COUPLERS (OPT.) SEAT BELT TILT CYLINDER FRONT AUXILIARY QUICK COUPLERS BUCKET ? SAFETY TREAD BUCKET STEPS OPERATOR CAB (ROPS & FOPS)? SEAT BAR REAR GRILL LIFT ARM SUPPORT DEVICE TAIL LIGHT LIFT ARM LIFT CYLINDER REAR LIGHT REAR DOOR B 12555 B 12556 TIRES* * TIRES Flotation tires are shown. The Bobcat loader is base equipped with standard tires. ? BUCKET Several different buckets and other attachments are available for the Bobcat loader. ? ROPS, FOPS Roll Over Protective Structure, Falling Object Protective Structure, per SAE J1040 and SAE J1043. The Bobcat loader is base equipped with standard operator cab as shown. 750 Series Loader Service Manual iii Revised Dec. 92

Melroe has engine oil blended to our specifications which meet or exceed the highest demands of your engine. Available at your local Bobcat Dealer. 750 Series Loader Service Manual iv

PREVENTIVE MAINTENANCE PREVENTIVE MAINTENANCE Page Number AIR CLEANER Replacement of the Filter Element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 7 ALTERNATOR BELT Adjusting the Alternator Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 15 DIAGNOSTIC TOOL Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 26 DRIVE BELT Adjustment Drive Belt Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 21 1 22 ENGINE COOLING SYSTEM Cleaning the Cooling System Coolant Level Removing Coolant from the Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 13 1 13 1 14 . . . . . . . . . . . . . . . . . . . . . . ENGINE LUBRICATION SYSTEM Checking Engine Oil Replacement of Oil and Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 11 1 11 FAN GEARBOX Checking Grease Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 20 FINAL DRIVE TRANSMISSION (CHAINCASE) Checking and Adding Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 20 FUEL SYSTEM Filling the Fuel Tank Fuel Filter Fuel Specifications Removing Air from the Fuel System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 9 1 9 1 9 1 10 HYDRAULIC/HYDROSTATIC SYSTEM Checking and Adding Fluid Hydraulic/Hydrostatic Filter Replacement Hydraulic Reservoir Breater Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 17 1 17 1 17 LIFT ARM SUPPORT DEVICE To Disengage Lift Arm Support Device To Engage Lift Arm Support Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 4 1 4 LIFTING AND BLOCKING THE LOADER Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 LIFTING THE LOADER Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3 LUBRICATION OF THE LOADER Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 23 MONITOR SERVICE CODES Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 27 OPERATOR CAB Description Lowering the Operator Cab Raising the Operator Cab Lowering the Operator Cab (W/Hand Controls) Raising the Operator Cab (W/Hand Controls) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 5 1 5 1 5 1 5b 1 5a . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 750 Series Loader Service Manual 1 1

PREVENTIVE MAINTENANCE (Contd) Page Number REMOTE START SWITCH Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 25 SEAT BAR SYSTEM Description Seat Bar Inspection Seat Bar Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 6 1 6 1 6 SENDER AND SENSORS Service Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 26 SERVICE CODES Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 28 SERVICE SCHEDULE Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 SPARK ARRESTOR MUFFLER Cleaning Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 18 TIRE MAINTENANCE Tire Inflation Tire Rotation Wheel Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 19 1 19 1 19 TRANSPORTING THE LOADER Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3 TROUBLESHOOTING THE B.O.S.S. & L.C.D. DISPLAY Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 30 USING AN BOOSTER BATTERY (JUMP STARTING) Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 16 750 Series Loader Service Manual 1 0

SERVICE SCHEDULE Maintenance work must be done at regular intervals. Failure to do so will result in excessive wear and early failures. The service schedule is a guide for correct maintenance of the Bobcat loader. Instructions are necessary before operating or servicing machine. Read Operation & Maintenance Manual, Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Failure to follow instructions can cause injury or death. WARNING W 2003 1289 SERVICE SCHEDULE HOURS ? ITEM SERVICE REQUIRED 8 10 50 100 250 1000 Engine Oil Air Cleaner Engine Cooling System Check the oil level & add oil as needed. Check display. Service only when required. Clean debris from oil cooler, radiator & grill. Check coolant level cold in recovery tank. Add 50/50 ethylene glycol & water as needed. Lubricate with multi purpose lithium based grease (20 places). Lift Arms. Cyl., Bob Tach Pivot Pins & Wedges Engine Air System Tires Seat Belt, Seat Bar & Pedal Interlocks Safety Signs & Safety Check for leaks & damaged components. Check for damaged tires & correct air pressure. Check the condition of seat belt. Check the seat bar & pedal interlocks correct operation. Clean dirt & debris from moving parts. Check for damaged signs (decals) & safety tread. Replace any signs or safety treads that are damaged or worn. Check the fastening bolts, washers & nuts. Check the condition of cab. Remove the trapped water. Check fluid level & add as needed. Check for damage & leaks. Repair & replace as needed. Check oil level. Operator Cab Fuel Filter Hyd. Fluid, Hoses & Tubelines Final Drive Trans. (Chaincase) Battery Control Pedals & Steering Wheel Nuts Check cables & electrolite level. Check for correct operation. Repair or adjust as needed. ? Check for loose wheel nuts & tighten to 105 115 ft. lbs. (142 156 Nm) torque. Check operation & adjust as needed. Check tension & adjust as needed. Replace oil & filter. Clean the spark chamber. ? Check for wear or damage. Make adjustment as needed. Replace filter element. Grease pivots as needed. Grease two fittings. ? Replace the filter element. Replace the reservoir breather cap. Check gear lube level. Replace the oil in the chaincase. Replace the fluid. Replace the filters. Parking Brake Alternator Belt Engine Oil & Filter Spark Arrestor Muffler Engine/Hydro. Drive Belt Fuel Filter Seat Bar Steering Shaft Hyd./Hydro. Filter Hyd. Reservoir Breather Cap Fan Drive Gearbox Final Drive Trans. Hyd. Reservoir Case Drain Filters ?Check wheel nut torque every 8 hours for the first 24 hours. ? Also replace hydraulic/hydrostatic filter element when the transmission warning light comes ON . ? Or Every 12 Months. ?Inspect the new belt after first 50 hours. 750 Series Loader Service Manual 1 1 Revised Dec. 92

1 PREVENTIVE MAINTENANCE A Instructions are necessary before operating or servicing machine. Maintenance Manual, Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Failure to follow instructions can cause injury or death. Read Operation & W 2003 0797 LIFTING AND BLOCKING THE LOADER B 07023 Procedure Always park the loader on a level surface. Put jackstands under the front axles and rear corners of the frame before running the engine for service. Failure to use jackstands can allow the machine to fall or move and cause injury or death. B W 2017 0286 Put floor jack under the rear of the loader [B]. Lift the rear of the loader and install jackstands [B]. CD 09027 Put the floor jack under the front of the loader [C]. C Lift the front of the loader and put jackstands under the axle tubes [C]. NOTE: Make sure the jackstands do not touch the tires. CD 09028 750 Series Loader Service Manual 1 2

TRANSPORTING THE LOADER A Procedure Adequately designed ramps of sufficient strength are needed to support the weight of the machine when loading onto a transport vehicle. Wood ramps can break and cause personal injury. W 2058 0494 MC 01241 A loader with an empty bucket or no attachment must be loaded backward onto the transport vehicle [A]. B Use the following procedure to fasten the Bobcat loader to the transport vehicle to prevent the loader from moving during sudden stops or when going up or down slopes [B]: 1. Lower the bucket or attachment to the floor. Stop the engine. 2. Engage the parking brake. 3. Install chains at the front and rear of the loader. CD 11165 CD 11166 LIFTING THE LOADER Procedure MC 01242 C AVOID INJURY OR DEATH Before lifting, check fasteners on four point lift. Never allow riders in the cab or bystanders within 15 feet (5 meters) while lifting the machine. W 2160 0694 The loader can be lifted with the four point lift which is available as a kit from your Bobcat loader dealer. Install the lift eyes in the kit as shown in Fig. [C]. MC 01434 750 Series Loader Service Manual 1 3 Revised Mar. 91

LIFT ARM SUPPORT DEVICE A To Engage Lift Arm Support Device Never work on a machine with the lift arms up unless the lift arms are secured by an approved lift arm support device. Failure to use an approved lift arm support device can allow the lift arms or attachment to fall and cause injury or death. CD 08693 W 2059 0598 B Maintenance and service work can be done with the lift arms lowered. If the lift arms are raised, use the following procedure: Put jackstands under the rear corners of the loader. Disconnect the spring from the lift arm support device retaining pin, hold onto the support device and remove the retaining pin [A]. Lower the lift arm support device on top of the lift cylinder. Hook the free end of the spring to the lift arm support device so there will be no interference with the support device installation. With the operator in the seat, seat belt fastened and seat bar lowered, start the engine. CD 08694 C Raise the lift arms, until the lift arm support device drops onto the lift cylinder rod [B]. Lower the lift arms slowly until the support device is held between the lift arm and the lift cylinder. Stop the engine. Raise the seat bar and unfasten the seat belt. Install pin into the rear of the lift arm support device below the cylinder rod. CD 08695 To Disengage Lift Arm Support Device Remove the pin from the lift arm support device. Connect the spring from the lift arm support device to the retainer plate on the lift arms [C]. With the operator in the seat, seat belt fastened and seat bar lowered, start the engine. Raise the lift arms a small amount and the spring will lift the support device off the lift cylinder rod. Lower the lift arms. Stop the engine. Lift the support device into the storage position and install the retaining pin and connect the spring [A]. 750 Series Loader Service Manual 1 4 Revised Jan. 92

OPERATOR CAB A Description The Bobcat loader has an operator cab (ROPS and FOPS) as standard equipment to protect the operator from rollover and falling objects. Replace the operator cab if it has been damaged. Never modify operator cab by welding, grinding, drilling holes or adding attachments unless instructed to do so by Melroe Company. Changes to the cab can cause loss of operator protection from rollover and falling objects, and result in injury or death. PI 06875 B W 2069 1285 Raising the Operator Cab Stop the loader on a level surface. Lower the lift arms, if the lift arms must be up while raising the operator cab, install the lift arm support device (Page 1 4). PI 06876 Before the cab or the lift arms are raised for service, jackstands must be put under the rear corners of the frame. Failure to use jackstands can allow the machine to tip backward causing injury or death. C W 2014 0895 Loosen the nut (both sides) at the front corner of the operator cab [A]. Remove the nut and plate (both sides) [B]. Lift on the grab handle and bottom of the operator cab slowly until the cab latching mechanism engages and the cab is all the way up [C]. B 12687 D Lowering the Operator Cab Pull down on the bottom of the operator cab until it is stopped by the latching mechanism. Release the latching mechanism and pull the cab all the way down [D]. Install the nut and plate (both sides) [B]. Tighten the nuts to 40 50 ft. lbs. (54 68 Nm) torque. CD 07692 750 Series Loader Service Manual 1 5 Revised Jan. 92

OPERATOR CAB (Contd) A Raising the Operator Cab (W/Hand Controls) Stop the loader on a level surface. Lower the lift arms. Shut engine off. If the lift arms must be up while raising the operator cab, install the lift arm support device (Page 1 4). CD 11810 Before the cab or the lift arms are raised for service, jackstands must be put under the rear corners of the frame. Failure to use jackstands can allow the machine to tip backward causing injury or death. B W 2014 0895 Disconnect the control linkage joint from the bottom hole (work position) and move to the TOP hole on the control handle (both sides) [A]. Both control handles must be in the vertical position so there will be no cab interference with the steering levers when the operator cab is raised or lowered [B]. CD 11809 C AVOID INJURY OR DEATH Accidental movement of the loader, the lift arms or the attachment can occur if the lift or tilt control handles are not positioned correctly before lifting or lowering the cab. Move control linkage to top hole in handles as shown, so cab does not hit handles when being lifted or lowered. W 2157 0594 B 06875 Loosen the nut (both sides) at the front corner of the operator cab [C]. D Remove the nut and plate (both sides) [D]. B 06876 750 Series Loader Service Manual Revised Jan. 92 1 5a

OPERATOR CAB (Contd) A Lift on the grab handle and bottom of the loader cab slowly until the cab latching mechanism engages and the cab is all the way up [A]. B 12687 Lowering the Operator Cab (W/Hand Controls) B Pull down on the bottom of the operator cab until it stops at the latching mechanism. Release the latching mechanism and pull the cab all the way down [B]. CD 07692 C Install the plate and nut (both sides). Tighten the nuts to 40 50 ft. lbs. (54 68 Nm) torque [C]. PI 06875 D Move the control linkage from the top hole to the BOTTOM hole (work position) on the control handle (both sides) [D]. CD 11810 750 Series Loader Service Manual Added Sept. 91 1 5b

SEAT BAR SYSTEM A Description The seat bar system has a pivoting seat bar with arm rests and has spring loaded interlocks for the lift and tilt control pedals. The operator controls the use of the seat bar. The seat bar in the down position helps to keep the operator in the seat, also the interlocks require the operator to lower the seat bar in order to operate the foot pedal controls. When the seat bar is up, the lift and tilt pedals are locked when returned to the neutral position. Clean & Lubricate B 07387 B AVOID INJURY OR DEATH The seat bar system must lock the lift and tilt control pedals in neutral when the seat bar is up. Service the system if pedals do not lock correctly. Clean W 2105 1285 Seat Bar Inspection Sit in the seat and fasten the seal belt. Engage the parking brake. Pull the seat bar all the way down. Start the engine. Operate each foot pedal to check both the lift and tilt functions. Raise the lift arms until the bucket is about 2 feet (600 mm) off the ground. P 01640 Raise the seat bar. Try to move each foot pedal. Pedals must be firmly locked in neutral position. There must be no motion of the lift arms or tilt (bucket) when the pedals are pushed. Pull the seat bar down, lower the lift arms and place the bucket flat on the ground. Stop the engine. Raise the seat bar and operate the foot pedals to be sure that the pedals are firmly locked in the neutral position. Un buckle the seat belt. Seat Bar Maintenance See the Service Schedule (Page 1 1) for the correct service interval. Clean any debris or dirt from the moving parts [A] & [B]. Inspect the linkage bolts and nuts for tightness. Use a general purpose grease to lubricate the seat bar pivot points on each side of the cab [A]. If the seat bar system does not function correctly, check for free movement of each linkage part. Check for excessive wear. Adjust pedal control linkage. Replace parts that are worn or damaged. Use only genuine Melroe replacement parts. 750 Series Loader Service Manual Revised Sept. 93 1 6

AIR CLEANER A Replacement of the Filter Element It is important to change the air filter element only when the service code (on the instrument panel) shows the symbol as shown in figure [A]. B 12914 B Service the air cleaner as follows: Remove the dust cover wing nut [B]. CD 08697 C Remove the dust cover [C]. CD 06877 D Remove the wing nut holding the large air filter element [D]. CD 08698 750 Series Loader Service Manual 1 7

AIR CLEANER (Contd) A Remove the large filter element [A]. NOTE: Make sure all sealing surfaces are free of dirt and debris. Install the new filter element and tighten the wing nut. Install the dust cover and tighten the wing nut. Check the air intake hose for damage. Check the air cleaner housing for damage. Check to make sure all connections are tight. CD 06878 B Only replace the inner filter element under the following conditions [B]: 1. Every third time the outer filter is replaced. 2. When the service code shows the symbol (Page 1 7, Figure [A]), only after the outer filter element has been changed and the engine speed is at full RPM. CD 06879 750 Series Loader Service Manual 1 8

FUEL SYSTEM A Fuel Specifications Use only clean, high quality fuel. Use Grade No. 2 fuel above 40 F (4 C). Use Grade No. 1 fuel at temperatures below 40 F (4 C). Filling the Fuel Tank CD 06880 Stop and cool the engine before adding fuel. NO SMOKING! Failure to obey warnings can cause an explosion or fire. B WRONG W 2063 0887 Remove the fuel fill cap [A]. Use a clean, approved safety container to add fuel of the correct specifications. Add fuel only in an area that has free movement of air and no open flames or sparks. NO SMOKING! [B]. Install and tighten the fuel fill cap [A]. B 13456 C Fuel Filter Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil. Failure to use care around combustibles can cause explosion or fire which can result in injury or death. CD 06881 W 2103 1285 D See the Service Schedule (Page 1 1) for the service interval when to remove the water from the fuel filter. Loosen the drain at the bottom of the filter element to drain the water from the filter [C]. See the Service Schedule (Page 1 1) for the service interval when to replace the fuel filter. Use a filter wrench to remove the filter element (Item 1) [D]. CD 06882 750 Series Loader Service Manual 1 9 Revised Mar. 91

FUEL SYSTEM (Contd) A Clean the area around the filter housing. Put oil on the seal of the new filter element. Install the fuel filter. Remove the air from the fuel system (See Below). Removing Air from the Fuel System After replacing the fuel filter element or when the fuel tank has run out of fuel, the air must be removed from the fuel system to start the engine. Open the vent on the fuel filter housing [A]. CD 10088 Operate the hand pump (priming bulb) until fuel flows from the vent with no air bubbles [B]. B Close the vent on the fuel filter housing [A]. CD 06884 C Open the vent on the fuel injection pump [C]. Operate the hand pump (priming bulb) until the pump feels solid [B]. Tighten the vent plug [C]. Start the engine. It may be necessary to open the vent plug (at the injection pump) briefly until the engine runs smoothly. CD 06883 Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil. Failure to use care around combustibles can cause explosion or fire which can result in injury or death. W 2103 1285 750 Series Loader Service Manual 1 10

ENGINE LUBRICATION SYSTEM A Checking Engine Oil Check the oil level every day. Before starting the engine for the work shift. Open the rear door. Remove the dipstick [A]. Keep the oil level between the marks on the dipstick. Use a good quality motor oil that meets API Service Classification of CC, CD or CE (See Oil Chart below). RECOMMENDED SAE VISCOSITY NUMBER (LUBRICATION OILS FOR ENGINE CRANKCASE) CD 06885 C 34 29 23 18 13 7 1 +4 +10 +15 +21 +27 +32 +38 +43 +49 +54 +60 B SAE 40 or 20W 50 SAE 10W 30 SAE 15W 40 SAE 5W 30 SAE 30W SAE 20W 20 SAE 10W F 30 20 10 0 +10 +20 +30 +40 +50 +60 +70 +80 +90 +100 +110 +120 +130+140 TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE (DIESEL: USE API CLASSIFICATION CC, CD OR CE) CD 06886 C Replacement of Oil and Filter See the Service Schedule (Page 1 1) for the service interval for replacing the engine oil and filter. 1. Run the engine until it is at operating temperature. Stop the engine. 2. Open the rear door. Remove the drain plug [B]. Drain the oil into a container. 3. Remove the oil filter [C]. 4. Clean the filter housing surface. Put clean oil on the new oil filter gasket. Install the filter and hand tighten only. CD 06887 5. Install and tighten the drain plug [B]. 750 Series Loader Service Manual 1 11 Revised Jan. 92

ENGINE LUBRICATION SYSTEM (Contd) A 6. Remove the filler cap from the valve cover [A]. CD 09371 B 7. Put 7.5 qts (7,1 L) of oil in the engine (See Oil Chart, Page 1 11) [B]. 8. Start the engine and let it run for several minutes. Stop the engine. Check for leaks and check the oil level. Add oil as needed if it is not at the top mark on the dipstick. Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil. Failure to use care around combustibles can cause explosion or fire which can result in injury or death. PI 06927 W 2103 1285 750 Series Loader Service Manual 1 12 Revised Apr. 91

MORE MANUALS: https://www.ebooklibonline.com/ Suggest: If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading

ENGINE COOLING SYSTEM A Cleaning the Cooling System Check the cooling system every day to prevent over heating, loss of performance or engine damage. Wear safety glasses to prevent eye injury when any of the following conditions exist: When fluids are under pressure. Flying debris or loose material is present. Engine is running. Tools are being used. CD 06888 B W 2019 1285 Raise the rear grill. Use air pressure or water pressure to clean the top of the oil cooler [A]. Raise the oil cooler and clean the top of the radiator [B]. Check the cooling system for leaks. CD 06889 C Coolant Level Open the rear door. Check the coolant level in the coolant recovery tank on the right side of the engine [C]. The coolant recovery tank must be 1/3 full. Add pre mixed coolant, 50% water and 50% ethylene glycol to the recovery tank if the coolant level is low. CD 06890 750 Series Loader Service Manual 1 13

https://www.ebooklibonline.com Hello dear friend! Thank you very much for reading. Enter the link into your browser. The full manual is available for immediate download. https://www.ebooklibonline.com